Kyocera Error 3101
TECHNOLOGY IN THIS DISCUSSION Kyocera 84 Followers Follow Kyocera CS-3050 Join the Community! Creating your account only takes a few minutes. Join Now Here's a weird one. I have a Kyocera CS 3050ci configured to scan to email using a local Exchange server. The thing works fine except on a few occasions when it prints out an error that says "Error Type : Transfer" with no real details about the error. The funny thing is that the scan to email job sends through just fine. Has anyone seen this behavior before? Do you have a fix? We've ignored the error mostly, but it happens frequently enough that it's an annoyance (and waste of paper). Tags: Kyocera CS-3050Review it: (1) Reply Subscribe View Best Answer RELATED TOPICS: Kyocera 400ci Scan-to-email error 0x3101 Scan to email error Email Error Help??   15 Replies Serrano OP Dunec Mar 24, 2014 at 8:17 UTC Someone will have to catch the Code (4 Digit Number) displayed on the OP Panel when it beeps with the error message. For some reason Kyocera decided to not print that on the error sheet that prints out. Most likely the Server is responding with a message the Kyocera is interpreting as an error. Does it seem to matter if its an internal or external email address when the error occurs? 3 Poblano OP finalbowser Mar 24, 2014 at 8:30 UTC Gold Key Technology Solutions is an IT service provider. We're only using internal contacts with this device. 0 Serrano OP Best Answer Dunec Mar 24, 2014 at 8:37 UTC Looking over the error codes, I only saw one relating to "Transfer". Might try setting the Numeric IP for the SMTP server, or lengthening the timeout wait.Error CodeScan OperationExplanationCauseHow to correct2202SCAN TO EMAILError: network transfer with timeout Networ
Hottest Threads / Posts Forum Rules What's New? Advanced Search Forum Technical Forums Copier Technical Discussion Kyocera Mita, Copystar KM-5050 SMTP set up error If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. Page 1 of 2 12 Last Jump to page: Results 1 to 10 of 13 Thread: KM-5050 SMTP set up error https://community.spiceworks.com/topic/462515-kyocera-cs-3050ci-scan-to-email-error-but-it-still-wok Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode 02-11-2009 #1 sprout Guest KM-5050 SMTP set up error hi, I need to set up SMTP from a KM5050. I have made all the correct settings and have allowed the IP and username to relay on Exchange server (2003). However, when I click http://www.copytechnet.com/forums/kyocera-mita-copystar/17447-km-5050-smtp-set-up-error.html TEST on the http KM5050 Command Centre, it gives: "Error (0x3101)" I cannot find any info on this error code - can anyone help? Settings are: SMTP = ONPort = 25SMTP Server = exchangeserverNameSMTP Timeout = 180 secondsAuthentication Protocol = ONAuthenticate As = OTHERUser name = USERNAME (that has been allowed in relay)Password = ++++++++Please help! Cheers. Reply With Quote 02-11-2009 #2 aragul View Profile View Forum Posts Private Message Senior Tech 100+ Posts Join Date Dec 2007 Posts 130 Post Thanks / Like Thanks (Given) 0 Thanks (Received) 0 Likes (Given) 0 Likes (Received) 0 Dislikes (Given) 0 Dislikes (Received) 0 Rep Power 19 All of the send error codes are described in the Basic Operation Guide under Troubleshooting. 2101, 2102, 2103, 2201, 2202, 2203, 3101: The network cable is disconnected or the hub that it is connected to is not operating properly. Check the cable and the hub. Otherwise, the server name or the host name of the SMTP server is not set correctly. Use COMMAND CENTER and register the SMTP server name and the host name correctly. If you can print to the 5050, you know the network connection to the machine is fi
365 with Admin credentials2. Select Home3. Select Options http://dnet-km.com/eve/forums/a/tpc/f/6716013712/m/1463967077 under Outlook 4. Select Settings for POP, IMAP, and SMTP access... 5. Record kyocera error the SMTP Settings for your account Setup the MFP with your Office 365 account 1. Open the Command Center RX2. Login as Admin3. Advanced Tab > SMTP Generala. SMTP Port Number: kyocera error 3101 587b. SMTP Server Name: pod#####.outlook.com Note: Enter your Server Name from abovec. Authentication: Ond. Authenticate As: Othere. User Name and Password: Office 365 User Name and Passwordf. SMTP Security: STARTTLS 4. E-Mail Settingsa. Sender Address: Should be the same as the Login User Name in SMTP General 5. Click Submit6. Test Office 365 E-Mail Setup.pdf (500 KB) Was this article helpful? 1 out of 1 found this helpful Facebook Twitter LinkedIn Google+ Have more questions? Submit a request 0 Comments Please sign in to leave a comment. Powered by Zendesk
SearchSearch current forum only Advanced SearchNew Since your Last VisitActive Topics in this CategoryAdd to My FavoritesPrinter Friendly FormatHelpManage TopicManage Content in This TopicManage MembersOnline NowControl PanelSetup Google mail (Gmail) on Scan to emailLogin/JoinWelcome, [Logout]StephanSenior Member posted March 22, 2012 12:38 AMHi Struggling with the settings needed to set-up scan to Email using gmail server settings.wondering if anybody have successfully set-up a scan to Email using gmail.My client uses Google to host their Mail and website.Google needs ssl and authentication for the smtp.I used all the same settings found on MS outlook mail set-up. ssl, port, authentication, smtp server but no joy.I keep on getting send error 3101.If anybody got ideas please help.Thank you in advance."Imagination is more important than knowledge" Posts: 170|Location: South Africa|Registered: May 30, 2011 IP Todd A.Senior Member posted March 22, 2012 05:14 AMHide PostWhat model machine are you working on ?quote:Originally posted by Stephan:Hi Struggling with the settings needed to set-up scan to Email using gmail server settings.wondering if anybody have successfully set-up a scan to Email using gmail.My client uses Google to host their Mail and website.Google needs ssl and authentication for the smtp.I used all the same settings found on MS outlook mail set-up. ssl, port, authentication, smtp server but no joy.I keep on getting send error 3101.If anybody got ideas please help.Thank you in advance. Posts: 362|Location: CA|Registered: November 07, 2003 IP Ignored post by Todd A. posted March 22, 2012 05:14 AMShow PostStephanSenior Member posted March 22, 2012 09:19 AMHide PostThe Model is FS-1128."Imagination is more important than knowledge" Posts: 170|Location: South Africa|Registered: May 30, 2011 IP Ignored post by Stephan posted March 22, 2012 09:19 AMShow PostTodd A.Senior Member posted March 22, 2012 09:40 AMHide PostI dont think the 1128 has SSL,But I would have to look at one to be sure.I thought only the new taskalfa have SSL for emailquote:Originally posted by Stephan:The Model is FS-1128. Posts: 362|Location: CA|Registered: November 07, 2003 IP Ignor