Error Offending Command Timeout
Contents |
great a time gap between receiving two portions of the same job. This error seems to have disappeared now that slower connections such as serial error timeout offending command timeout stack or parallel lines are no longer used. Solutions An obvious solution is error timeout 0x0005 to try a different type of connection, if that is possible. If your printer is hooked up to error timeout offending command timeout hp a router, try connecting it directly to your computer. If it has multiple types of connections, try another one. Check out your driver settings - maybe a higher speed syntax error offending command or different communication settings solve the issue. Using binary encoding is a typical example of this. Some systems expect a Control-D or Control-Z character at the end of the print job to terminate it. Some drivers have an option to enable this. On some systems there are tools that allow you to change the timeout value of the
Syntax Error Offending Command Nostringval
RIP or printer. By making the device wait a little longer while receiving data, the PostScript error can be avoided. On some Lexmark printers for instance, adding the following to the beginning of the job: << /JobTimeout 0 >> setuserparams sets the job timeout value for that job to 0 which means that it should not timeout regardless of how long it takes. Her is another example, taken from a manual for a Xante printer: "The Timeout feature allows you to select the number of seconds the printer waits for additional data before cancelling a job and returning to the READY/IDLE state. Set Timeout from the MISC:TIMEOUT configuration menu. The factory default of 40 seconds (40 Sec) is an average setting. Set timeout according to the type of files you send. Use a low setting for small, simple files to prevent an indefinite tie-up on one job. Use the 300 or Never setting for large files, such as graphic intensive or CAD (Computer Aided Design) files, to allow enough processing time. With the N
COMMAND: timeoutSTACK:---It may print on error undefined offending command pscript_winnt_compat a separate sheet, or it may print at the top of a sheet, then print the https://www.prepressure.com/postscript/troubleshooting/errors/timeout rest of the content.Any suggestions?Thank youVictor Reinhart Respond to this 0 What Jetdirect card? If you have newer routers or upgraded servers, the issue may be throughput is too fast. Get a http://www.fixyourownprinter.com/posts/62478 620, or even the 10/100/1000. More printer memory may not help that much. by unknown on Jun 8, 2009 at 3:42pm Add comment Please sign in to comment 0 You also might want to try a different print driver. Like if using a PCL6 driver try a PCL5 or vise versa. by nivek on Jun 8, 2009 at 4:34pm Add comment Please sign in to comment Please sign in to comment HP DesignJet 100 Buy discount ink Buy this printer More HP questions © Copyright 2011-2016, FixYourOwnPrinter.com, Inc. Privacy Policy Terms of Use
Hired as an Part time Consultant to help them to migrate their old Server UPS With Network Shutdown Upgrade Install new APC UPS with network monitoring card & configure 5 devices https://community.spiceworks.com/topic/680595-printing-in-yosemite-prints-timeout-error-page-after-every-job to shutdown gracefully via APC PowerChute Network Edition utility. New Courthouse The Courts moved https://helpx.adobe.com/x-productkb/global/troubleshoot-postscript-errors.html from the top floor of our Police Station to a Consolidated Courthouse 5km away. Two strands of fibre connect the police station to the courthouse. TECHNOLOGY IN THIS DISCUSSION Join the Community! Creating your account only takes a few minutes. Join Now One of my users prints to an Oki C831 printer from his iMac, which offending command is running OS X Yosemite (10.10). The documents are printed successfully, but after every print job an error sheet is printed, which reads, verbatim: TextERROR: timeout OFFENDING COMMAND: timeout STACK: This happens every time a job is sent to the printer, and happens whether using the model-specific print driver from Oki or the generic driver in Yosemite. This problem does not occur with my Windows users, even when using PostScript drivers. I've error offending command already tried reinstalling the Oki drivers, running Oki's driver updater and using Repair Permissions on the OS disk in Disk Utility (for some reason the Yosemite upgrade messes up the printer library and the printers have the wrong permissions and group settings). While it's not such a big deal to remove the surplus sheets from the output tray, this error cumulatively wastes a lot of paper! Any advice would be much appreciated. Reply Subscribe View Best Answer   5 Replies Serrano OP Best Answer raycaruso Dec 10, 2014 at 1:09 UTC Do you have any other people printing from mac's with yosemite? I would say test with another machine, I had some issues with my Yosemite upgrade which forced me to do a clean install. 2 Cayenne OP Helpful Post macfixer Dec 10, 2014 at 2:21 UTC I would reset the printing system from within System Preferences. Then, set up the printer again. http://support.apple.com/en-us/HT201539 4 Thai Pepper OP skrysiak Dec 15, 2014 at 3:12 UTC raycaruso wrote: Do you have any other people printing from mac's with yosemite? I would say test with another machine, I had some issues with my Yosemite upgrade which forced me to do a clean install.Unfortunately I only have on
a PostScript error Applies to : Illustrator InDesign PageMaker Photoshop PostScript printer drivers You can receive a PostScript error when sending a file to a PostScript interpreter (for example, a printer, Acrobat Distiller). A PostScript error occurs when the PostScript interpreter can't read the file's PostScript code. An error can also occur if the file's PostScript code exceeds one or more of the limits in the PostScript page description language. If your PostScript interpreter appears to process data but then stops, a PostScript error could have occurred.A PostScript error message includes a PostScript error type, which defines the type of error it is. It also includes an offending command, which usually indicates the specific part of the PostScript code that the interpreter couldn't read. The offending command usually indicates the command that caused the problem. Some PostScript errors point you right to the cause of the problem, and some get you looking in the right direction.Example of a PostScript error:%%[Error: ; OffendingCommand: ]%%For example, the PostScript error %%[Error: dictfull; OffendingCommand: def ]%% contains the PostScript error type "dictfull" and the offending command "def." The error type indicates that the dictionary contains the maximum number of entries. The offending command is the last command the PostScript interpreter tried to process, "def," which defines a new word in the dictionary. View or print a PostScript error message If you think a PostScript error has occurred, but it doesn't appear onscreen or in your printout, you can sometimes view or print the error message. Do one or more of the following:Use an error handler utility. For example, Adobe PageMaker has the Include PostScript Error Handler option in the Print Options dialog box.In Windows, configure the printer to print the error message:Note: In Windows NT, you cannot configure a printer to print an error message. Choose one of the following: Start > Settings > Printers (Windows 2000)Start > Printers And Faxes (Windows XP)Start > Control Panel > Printers (Windows Vista, Windows 7) Right-click the printer you are using, and then choose Printer Properties. Select the General tab, select Printing Preferences, and then click Advanced. Expand Document Options, and then expand PostScript Options. Set Send PostScript Error Handler to Yes. If you do not see this option, your printer does not have a PostScript Error Handler. Note: If PostScript Options isn't visible, double-cl