Error Rangecheck Offending Command Image Stack Dictionary
Contents |
solutions Often a corrupted image leads to this type or error. You can easily trace which image causes the problem from applications like QuarkXPress that allow you to print jobs without the images. If the PostScript error doesn't error limitcheck offending command image occur then, you can start trying to locate the bad image. Set half of error undefined offending command stack your images to non-printing and try printing again. Again halve the amount of images and print again and keep doing this until you offending command nostringval located the bad one. Updating your application and/or printer driver to the latest release could also solve issues with an offending command ‘Image' error. If the info below doesn't point to a more specific work-around, try the error undefined offending command stack xerox basic troubleshooting tips. PostScript error Limitcheck If you get a PostScript error ‘limitcheck' offending command ‘image', an image in your document is too large, its resolution is too high or it cannot be rotated. Reduce the size or resolution, rotate the image at a different angle or rotate it in an application like Photoshop. Some older level 2 versions of PostScript RIPs as well as Acrobat Distiller 4.0 (and 4.05 and probably 3.x) cannot handle
Error Limitcheck Offending Command Save
copydot files in which the number of pixels exceeds 32000 in either direction. Using such big copydot files (eg larger than about 33 centimeters for a 2400 dpi copydot) can lead to a PostScript error "limitcheck" offending command "image". If you get a PostScript error "limitcheck" offending command "image" when printing from InDesign 1.0, the document probably contains a multitone EPS (duotone, tritone,.. ) that uses a spot color. To get around the error, you can either perform the colour separation in InDesign itself (deselect "In-RIP" in the separations tab) or you should upgrade your RIP to Adobe PostScript version 3011 or later. PostScript error IOerror An ‘ioerror', offending command ‘image' or ‘colorimage' points to an incorrect amount of data in an image or it indicates that the printer's PS interpreter reads beyond the end of the job while rendering an image. Two possible solutions: Make sure that the channel used to connect the printer to your system is truly binary or try to change you printer driver's settings from binary to ASCII. In general, parallel (Centronics) interfaces do not support binary datatransfer, serial and network interfaces do. Scan, edit or import the image again. PostScript error Typecheck or Rangecheck A PostScript error ‘typecheck' or ‘rangecheck' orrurs when you try printing a PostScript level 2 file to a PostScript level 1 d
CommunityCategoryBoardUsers turn on suggestions Auto-suggest helps you quickly narrow down your search results by
Error Syntax Error Offending Command Stack
suggesting possible matches as you type. Showing results for Search error limitcheck offending command mac instead for Do you mean Reply Topic Options Subscribe to RSS Feed Mark Topic as postscript errors New Mark Topic as Read Float this Topic to the Top Bookmark Subscribe Printer Friendly Page « Message Listing « Previous Topic Next Topic » beinformedsd https://www.prepressure.com/postscript/troubleshooting/errors/image New Member Posts: 2 Registered: 08-05-2011 ERROR: limitcheck OFFENDING COMMAND: Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 08-05-2011 02:16 AM Hi,I'm using a Xerox WorkCentre 7545 with the Postscript driver. Serveral users report that they get the message "ERROR: limitcheck http://forum.support.xerox.com/t5/Printing/ERROR-limitcheck-OFFENDING-COMMAND/td-p/7530 OFFENDING COMMAND:" when printig a Word document. The document has 50 pages and after page 10 the printer stops with the error message. I have tried to break up the document in pieces, but after 10 pages the printer stops. It doesn't matter if you print page 1-10 or 11-20 etc.The print spooler is on a Windowws 2003 server. The client is Windows 7 with Office 2007.Any ideas? Solved! Go to Solution. Message 1 of 7 (53,600 Views) Reply 0 Kudos Fabio Frequent Advisor Posts: 1,540 Registered: 10-11-2010 Re: ERROR: limitcheck OFFENDING COMMAND: Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 08-05-2011 02:34 AM have you tried disabling : "advanced printing features" , you can find it if you open the printer properties, then the tab advanced, that at the bottom you can unchech that option Message 2 of 7 (53,599 Views
Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Display and Touch  Notebook Hardware and Upgrade http://h30434.www3.hp.com/t5/LaserJet-Printing/quot-ERROR-limitcheck-OFFENDING-COMMAND-image-STACK-quot/td-p/2233513 Questions  Notebook Software and How To Questions  Business Notebooks  Printers sprocket  Inkjet Printing  LaserJet Printing  Printer Software and Drivers  DesignJet, Large Format Printers and Digital Press  HP Connected, Mobile Printing and Cloud Printing  Scanning, Faxing, and Copying  JetAdvantage, Printing Applications and Services  Desktops Desktop Operating Systems and Recovery  Desktop Boot and offending command Lockup  Desktop Wireless and Networking  Desktop Audio  Desktop Video, Display and Touch  Desktop Hardware and Upgrade Questions  Desktop Software and How To Questions  Sprout by HP  Business PCs, Workstations and Point of Sale Systems  Gaming Gaming Notebooks  Gaming Desktops  Gaming Accessories  Tablets and Mobile Devices Elite x3  Android  Windows  Calculators  Palm and error limitcheck offending WebOS  Software HP Workspace  HP Touchpoint Manager  HP Collaboration  Commercial PC Software  Archived Topics (Read Only) Notebooks Archive (Read Only)  Printers Archive (Read Only)  Desktops Archive (Read Only)  Tablets and Mobile Devices Archive (Read Only)  Software Archive (Ready Only)  Windows Beta and Previews Archive (Read Only)  Miscellaneous Topics (Read Only)  Your Voice Forum Feedback & Suggestions  HP Expert Portal Welcome to the HP Expert Program  Meet the Experts  News and Events  Blogs Open Menu Blogs Open Menu Best of the Community BlogMeet the ExpertsNews and EventsWelcome to the HP Expert Program Beware of fake HP Support Open Menu Beware of fake HP Support Open Menu Be alert for scammers who may be posing as HP representatives and only call numbers from people who have a label next to their screen name. If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inapprop