Error Rangecheck Offendingcommand Fill
Contents |
solutions Often a corrupted image leads to this type or error. You can easily trace which image causes the problem from applications like QuarkXPress that allow you to print jobs without error undefined offending command stack the images. If the PostScript error doesn't occur then, you can start trying to
Error Rangecheck Offending Command Image
locate the bad image. Set half of your images to non-printing and try printing again. Again halve the amount of
Error Undefined Offending Command Stack Xerox
images and print again and keep doing this until you located the bad one. Updating your application and/or printer driver to the latest release could also solve issues with an offending command ‘Image' error.
Error Syntax Error Offending Command Stack
If the info below doesn't point to a more specific work-around, try the basic troubleshooting tips. PostScript error Limitcheck If you get a PostScript error ‘limitcheck' offending command ‘image', an image in your document is too large, its resolution is too high or it cannot be rotated. Reduce the size or resolution, rotate the image at a different angle or rotate it in an application like Photoshop. Some offending command nostringval older level 2 versions of PostScript RIPs as well as Acrobat Distiller 4.0 (and 4.05 and probably 3.x) cannot handle copydot files in which the number of pixels exceeds 32000 in either direction. Using such big copydot files (eg larger than about 33 centimeters for a 2400 dpi copydot) can lead to a PostScript error "limitcheck" offending command "image". If you get a PostScript error "limitcheck" offending command "image" when printing from InDesign 1.0, the document probably contains a multitone EPS (duotone, tritone,.. ) that uses a spot color. To get around the error, you can either perform the colour separation in InDesign itself (deselect "In-RIP" in the separations tab) or you should upgrade your RIP to Adobe PostScript version 3011 or later. PostScript error IOerror An ‘ioerror', offending command ‘image' or ‘colorimage' points to an incorrect amount of data in an image or it indicates that the printer's PS interpreter reads beyond the end of the job while rendering an image. Two possible solutions: Make sure that the channel used to connect the printer to your system is truly binary or try to change you printer driver's settings from binary to ASCII. In general, parallel (Centronics) interfaces do not support binary datatrans
command. Each term is linked to a page with more detailed information error unregistered offending command show and possible work-arounds. It may be worthwhile to check both error unregistered offending command xshow the error message and the command that caused the error to appear. If you are not pdf error 19 postscript error undefined entirely sure which PostScript error you encountered, first read this page. If you encountered an error that is not listed and managed to find more https://www.prepressure.com/postscript/troubleshooting/errors/image information about it, please add a comment about it to this page. Thanks! / 3.31 -4100 -8133 -8993 8BPS A A4tray addglyph AGMCORE_gstack aldusdict2 aload ashow awidthshow B banddevice bdef bitspercomponent buildchar C CCRun charpath clip colorimage configurationerror ct_cffdict cs(PDF) CT_T3HdrDICT currentpoint curveto D DCTdecodefilter def dict dictfull dictstackoverflow dictstackunderflow https://www.prepressure.com/postscript/troubleshooting/errors div do(PDF) E end endcidrange eoclip eofill EPS_Dict exch exec execstackoverflow F featurecleanup fhiscomposite fill filter filtered ruling findfont flxproc FMc FmPD FmPD2 FmPA fontsave forall framedevice G get getinterval gsave H handleerror havefont I image imagedistiller imagemask index inf interrupt invalidaccess invalidcontext invalidexit invalidfileaccess invalidfont invalidid invalidrestore interrupt ioerror ISOLatin1Encoding itransform K kshow L limitcheck Is2016andT32? lineto lipping M makeblendedfont makefont md mmxpr3 moveto MSTT
OFFENDING COMMAND: filter) - Adobe Acrobat Windows We are attempting to print off some rather large image files on a Xerox 340 and an HP Laserjet 4MV printer via http://www.justskins.com/forums/postscript-print-error-error-100990.html Adobe Acrobat 6. Smaller similar files print fine, but when we try to print some of the larger files we get a sheet with the following printed instead of the image: ------------------------------------------------ ERROR: rangecheck OFFENDING COMMAND: filter STACK: /CCITTFaxDecode -dictionary- -filestream- -filestream- -mark- /_Filters [1.0 0.0 ] /Decode 1 /BitsPerComponent [25386.0 0.0 0.0 -6552.0 0.0 6552.0 ] /ImageMatrix 6552 /Height offending command 25386 /Width 1 /ImageType -mark- -savelevel- ---------------------------------------------------- From searching the Adobe site, it sounds like the "ERROR: rangecheck" ... Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode May 12th,09:05 PM #1 Postscript Print error (ERROR: rangecheck; OFFENDING COMMAND: filter) We are attempting to print off some offending command stack rather large image files on a Xerox 340 and an HP Laserjet 4MV printer via Adobe Acrobat 6. Smaller similar files print fine, but when we try to print some of the larger files we get a sheet with the following printed instead of the image: ------------------------------------------------ ERROR: rangecheck OFFENDING COMMAND: filter STACK: /CCITTFaxDecode -dictionary- -filestream- -filestream- -mark- /_Filters [1.0 0.0 ] /Decode 1 /BitsPerComponent [25386.0 0.0 0.0 -6552.0 0.0 6552.0 ] /ImageMatrix 6552 /Height 25386 /Width 1 /ImageType -mark- -savelevel- ---------------------------------------------------- From searching the Adobe site, it sounds like the "ERROR: rangecheck" indicates there is a problem with "unintelligible PostScript code", however I cannot find any reference to what "OFFENDING COMMAND: filter" means or how to fix this problem. If anyone has any information or suggestions, I would love to hear from you. Thanks Darrell_J_Brown@adobeforums.com Guest May 13th,11:24 AM #2 Re: Postscript Print error (ERROR: rangecheck; OFFENDING COMMAND: filter) Looks like the rip on your pritners simply can't deal with the ps date it's being send. rangecheck noprmally means that a value is too large for the rip tooh