Pdf Printing Error Limitcheck
Contents |
CommunityCategoryBoardUsers turn on suggestions Auto-suggest helps you quickly narrow down your search results by suggesting possible error undefined offending command stack matches as you type. Showing results for Search instead for Do
Error Limitcheck Offending Command Save
you mean Reply Topic Options Subscribe to RSS Feed Mark Topic as New Mark Topic as
Error Limitcheck Offending Command Mac
Read Float this Topic to the Top Bookmark Subscribe Printer Friendly Page « Message Listing « Previous Topic Next Topic » beinformedsd New Member Posts: 2 Registered:
Error Limitcheck Offending Command Gsave
08-05-2011 ERROR: limitcheck OFFENDING COMMAND: Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 08-05-2011 02:16 AM Hi,I'm using a Xerox WorkCentre 7545 with the Postscript driver. Serveral users report that they get the message "ERROR: limitcheck OFFENDING COMMAND:" when printig a Word document. The error limitcheck offending command addglyph stack dictionary document has 50 pages and after page 10 the printer stops with the error message. I have tried to break up the document in pieces, but after 10 pages the printer stops. It doesn't matter if you print page 1-10 or 11-20 etc.The print spooler is on a Windowws 2003 server. The client is Windows 7 with Office 2007.Any ideas? Solved! Go to Solution. Message 1 of 7 (54,287 Views) Reply 0 Kudos Fabio Valued Advisor Posts: 1,557 Registered: 10-11-2010 Re: ERROR: limitcheck OFFENDING COMMAND: Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 08-05-2011 02:34 AM have you tried disabling : "advanced printing features" , you can find it if you open the printer properties, then the tab advanced, that at the bottom you can unchech that option Message 2 of 7 (54,286 Views) Reply 0 Kudos beinformedsd New Member Posts: 2 Registered: 08-05-2011 Re: ERROR: limitcheck OFFENDING COMMAND: Opti
solutions Often a corrupted image leads to this type or error. You can easily trace which image causes the problem from applications like QuarkXPress that allow you to print jobs without offending command nostringval the images. If the PostScript error doesn't occur then, you can start trying to xerox error undefined offending command stack locate the bad image. Set half of your images to non-printing and try printing again. Again halve the amount of error: limitcheck mac images and print again and keep doing this until you located the bad one. Updating your application and/or printer driver to the latest release could also solve issues with an offending command ‘Image' error. http://forum.support.xerox.com/t5/Printing/ERROR-limitcheck-OFFENDING-COMMAND/td-p/7530 If the info below doesn't point to a more specific work-around, try the basic troubleshooting tips. PostScript error Limitcheck If you get a PostScript error ‘limitcheck' offending command ‘image', an image in your document is too large, its resolution is too high or it cannot be rotated. Reduce the size or resolution, rotate the image at a different angle or rotate it in an application like Photoshop. Some https://www.prepressure.com/postscript/troubleshooting/errors/image older level 2 versions of PostScript RIPs as well as Acrobat Distiller 4.0 (and 4.05 and probably 3.x) cannot handle copydot files in which the number of pixels exceeds 32000 in either direction. Using such big copydot files (eg larger than about 33 centimeters for a 2400 dpi copydot) can lead to a PostScript error "limitcheck" offending command "image". If you get a PostScript error "limitcheck" offending command "image" when printing from InDesign 1.0, the document probably contains a multitone EPS (duotone, tritone,.. ) that uses a spot color. To get around the error, you can either perform the colour separation in InDesign itself (deselect "In-RIP" in the separations tab) or you should upgrade your RIP to Adobe PostScript version 3011 or later. PostScript error IOerror An ‘ioerror', offending command ‘image' or ‘colorimage' points to an incorrect amount of data in an image or it indicates that the printer's PS interpreter reads beyond the end of the job while rendering an image. Two possible solutions: Make sure that the channel used to connect the printer to your system is truly binary or try to change you printer driver's settings from binary to ASCII. In general, parallel (Centronics) interfaces do not support binary datatrans
a PostScript error Applies to : Illustrator InDesign PageMaker Photoshop PostScript printer drivers You can receive a PostScript error when sending a file to a PostScript interpreter (for example, a printer, https://helpx.adobe.com/x-productkb/global/troubleshoot-postscript-errors.html Acrobat Distiller). A PostScript error occurs when the PostScript interpreter can't read the file's PostScript code. An error can also occur if the file's PostScript code exceeds one or more of the limits in the PostScript page description language. If your PostScript interpreter appears to process data but then stops, a PostScript error could have occurred.A PostScript error message includes a PostScript error type, which offending command defines the type of error it is. It also includes an offending command, which usually indicates the specific part of the PostScript code that the interpreter couldn't read. The offending command usually indicates the command that caused the problem. Some PostScript errors point you right to the cause of the problem, and some get you looking in the right direction.Example of a PostScript error:%%[Error: ; OffendingCommand: error limitcheck offending ]%%For example, the PostScript error %%[Error: dictfull; OffendingCommand: def ]%% contains the PostScript error type "dictfull" and the offending command "def." The error type indicates that the dictionary contains the maximum number of entries. The offending command is the last command the PostScript interpreter tried to process, "def," which defines a new word in the dictionary. View or print a PostScript error message If you think a PostScript error has occurred, but it doesn't appear onscreen or in your printout, you can sometimes view or print the error message. Do one or more of the following:Use an error handler utility. For example, Adobe PageMaker has the Include PostScript Error Handler option in the Print Options dialog box.In Windows, configure the printer to print the error message:Note: In Windows NT, you cannot configure a printer to print an error message. Choose one of the following: Start > Settings > Printers (Windows 2000)Start > Printers And Faxes (Windows XP)Start > Control Panel > Printers (Windows Vista, Windows 7) Right-click the printer you are using, and then choose Printer Properties. Select the General tab, select Printing Preferences, and then click Advanced. Expand Document Options, and then expand PostScript Options