Ios Error Windows 98
Contents |
initializing device IOS: Error: An I/O subsystem driver failed to load" at boot. Temporarily rename your autoexec.bat and config.sys by following the steps below: Boot the computer to an MS-DOS prompt. Once at the while initializing device ios windows protection error windows 95 DOS prompt type:C:
Windows Protection Error Windows 95 Virtualbox
Once the above has been successfully completed reboot the computer. Additional information about the autoexec.bat and config.sys can be found on our
Windows Protection Error Windows 98 Virtualbox
autoexec.bat and config.sys page. Issue with SMARTDRV.EXE or RMM.PDR The steps below can resolve any of the following errors: "Windows protection error", "IOS error", "While initializing device IOS: Windows protection error. You must restart your computer.",
Windows Protection Error You Need To Restart Your Computer 98
"While initializing IOS: Windows protection error. You need to restart your computer.", "Windows initializing device IOS: Windows protection error. IOS failed to initialize, please restart" or "Windows initializing device IOS: Windows protection error. You need to restart your computer" in Windows 95. Temporarily rename the SMARTDRV.EXE and the RMM.PDR by following the steps below. Boot the computer to an MS-DOS prompt. Once at the DOS prompt type:C:
Database CPUs Solaris Novell OpenVMS DOS Unix Mac Lounge Login» Register» Connect» Hardware & Devices ▼ General Hardware CPUs/Overclocking Networking See More... Software ▼ Security and windows 95 protection error startup Virus Office Software PC Gaming See More... Operating Systems ▼ Windows 10 Windows 8 windows protection error ndis Windows 7 Windows XP See More... Off-Topic Tags How-tos Drivers Ask a Question Computing.NetForumsWindows 95/98Installation Solved Win 95: Windows protection error after 13. non-system disk or disk error. replace and press any key when ready setup Tags:Microsoft Windows 95windows 95setup N7I2S5 May 7, 2011 at 12:08:39 Specs: Windows 95 & Windows 7, AMD Athlon II X2 250 3GHz / Host: 4 GB RAM, VM: 256MB RAM I am trying to http://www.computerhope.com/issues/ch000359.htm set up Windows 95 on a VM using Microsoft Virtual PC 2007 with a 8 GB VHD. Everything works fine until it finishes setup, but it when it tries to start Windows for the first time, it says, "While initializing device IOS: Windows protection error. You need to restart your computer." I have tried booting up in safe mode and have formatted the VHD and reinstalled it several times, but I can't http://www.computing.net/answers/windows-95/win-95-windows-protection-error-after-setup/170738.html figure out why it won't work. It worked fine once before, but the hard drive it was on went bad, so I have to set it up again. Thank you for any help/solutions. See More: Win 95: Windows protection error after setup Report • #1 T-R-A May 7, 2011 at 12:57:04 Just curious, is it Win95, Win95A, or Win95B/C you're trying to run? Sound's something like the old >350MHz AMD CPU error:http://www.computerhope.com/issues/...Just speculating here, but you may be able to change some of the settings in VPC2K7 to "allow" for a slower CPU speed (if that indeed is the problem). I've worked with VPC2K4, but not 2K7, so I don't for sure. You may also want to try a smaller VHD partition (2GB or less)."Channeling the spirit of jboy..." Report • #2 sdfox 7 May 8, 2011 at 11:47:57 If the above solutions don't work you can try bumping the VM down to between 128MB and 192MB; I routinely use 95 on my various systems with 64MB-128MB and don't know if it would even cache 256MB properly.http://sdfox7.comhttp://marcusct.com Report • #3 LoneCrusader May 9, 2011 at 22:27:38 ✔ Best AnswerAs stated above, you have encountered the well-documented >350MHz processor error with Windows 95. Another similar one exists at speeds >2.1GHz. Both issues can be fixe
[ DST ] Get VirtualBox Forum powered by phpBB © phpBB Group By any use of this Website, you agree to be bound by these Policies and Terms of Use Sponsored by