F21 Error Code Whirlpool Duet Sport
Contents |
Microwave Oven Repair FAQ Oven Repair FAQ Range Repair FAQ Refrigerator Repair FAQ Stove Repair FAQ Laundry Appliances Dryer Repair FAQ Washing Machine Repair FAQ Repair Forums Buy Parts Newsletter Email Us Whirlpool Duet Washer with F-21 Fault Code 9 Replies This problem is
Whirlpool Duet Sport F 21
a good illustration of how there's just no substitute for actual hand-to-hand combat with broken appliances. f21 error code whirlpool duet steam Here's an excerpt from the service manual on this fault code: EXPLANATION AND RECOMMENDED PROCEDURE F21 LONG DRAIN If the drain time exceeds
Whirlpool Duet Steam F21
8 minutes the water valves turn off. NOTES:After 4 minutes the “Sd” error will be displayed, then 4 minutes later the “F/21” error code will be displayed. Press PAUSE/CANCEL two times to clear the display. Possible Causes/Procedure 1. Check https://www.youtube.com/watch?v=reZnmpTPgew the drain hose and make sure it is not plugged or kinked. 2. Unplug washer or disconnect power. 3. Check the electrical connections at the pump and make sure the pump is running. 4. Check the drain pump filter for foreign objects. 5. Plug in washer or reconnect power. 6. If the above does not correct the problem, go to step 7. 7. Unplug washer or disconnect power. 8. Replace the pump. I've worked on dozens of these http://fixitnow.com/wp/2008/09/27/whirlpool-duet-washer-with-f-21-fault-code/ washers and have only found the above service manual solution to apply once or twice. The vast majority of the time, I'd arrive and all the washer would do is drain and flash F-21 in the display. I couldn't even get the control board to go into diagnostic mode. Using my keen Samurai Insight, I unplugged the washer and removed the molex connector from the water level switch (also called a pressure switch). To get to it, remove the top panel by taking out the three screws in the back of the washer. The pressure switch is right there on top, as seen in the picture below: Anyway, I plugged the washer back in and, lo!, the washer did enter diagnostic mode and the people did sing and the Lord did grin. And there was much rejoicing. Especially after I replaced the water level switch whereupon appliantological harmony was restored. To learn more about your washing machine, or to order parts, click here. This entry was posted in Washer Repair on September 27, 2008 by Samurai Appliance Repair Man. Post navigation ← Weird Timer Problems in a Whirlpool / Kenmore Dryer with Electronic Control Samurai Fixit Cam → 9 thoughts on “Whirlpool Duet Washer with F-21 Fault Code” sbrown April 1, 2010 at 4:25 pm OK, I have had the same problem as above. I took what I considered to be a conservat
help with any question. Credentials confirmed by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our http://www.justanswer.com/appliance/6enrw-whirlpool-duet-ht-washer-f21-error-code.html site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate http://www.shopyourway.com/questions/1098875 the answer you receive. Ask Mike Your Own Question Mike, Home Appliance Technician Category: Appliance Satisfied Customers: 17629 Experience: I have been repairing appliances for 25 years, I run my own appliance repair business. 22302088 Type Your Appliance Question Here... Mike is online now What does the error code F21 whirlpool duet mean? The meaning of the error code and the corrective actions are listed below.F21LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. NOTES: After 4 minutes the “Sd” error will be displayed, then 4 minutes later the “F/21” error code will be displayed. Press PAUSE/CANCEL two times to clear the display.1. Check the drain hose and make sure whirlpool duet sport it is not plugged or kinked. 2. Unplug washer or disconnect power. 3. Check the electrical connections at the pump and make sure the pump is running. 4. Check the drain pump filter for foreign objects. 5. Plug in washer or reconnect power. 6. If the above does not correct the problem, go to step 7. 7. Unplug washer or disconnect power. 8. Replace the pump.The likely problem is either a blocked drain filter or a bad pump.Take the panel out from under the door by removing the 3 screws along the bottom lip .Behind the panel you will see the pump and built into the pump you will see the drain filter. Unscrew the drain filter and pull it out (have some towels handy to mop up the water)Clean the drain filter.Once clear try the machine again, if you have the same problem replace the drain pump. Read full interaction below ยป Share this conversation Question My whirlpool duet HT washer is showing an f21 fault code. I also can detect a faint odor that smells electrical. Is this thing shot? Submitted: 4 years ago. Category:Appl
published, help is on its way! front loader washing machine whirlpool duet broken says "F21" Report This by Manage My Life November 23rd, 2010 my front loader whirlpool duet washing machine stopped working. it keeps blinking and saying F21 i think it got overloaded with too many clothes can't open door Share it! Get more answers from the people in your networks Tags Whirlpool Click to remove this tagging. Add your answer Sign in to answer a question 3 Answers from these members: Not having a working washer can be a big inconvenience, to help you I have attached a link below to manage my life where a expert answered a similar question that can be very helpful. Hope it helps! by Manage My Life November 23rd, 2010 Answered in 8 minutes Comment Give your feedback by voting on answers 0 votes Thank you for your question. The F21 error code indicates a long drain time on this type of washer. The door will not unlock if the washer control detects that water is still in the tub. To manually unlock the washer door, take these steps: Unplug the washer to completely disconnect electrical power. Remove the bottom front service panel as shown in the first image below. Carefully reach up through the bottom opening and pull the release tab on the bottom of the door lock assembly until it clicks. NOTE: Internal metal edges in the washer can be sharp. Protective gloves are recommended for this procedure. By pulling the manual release tab on the door lock assembly, you should be able to get the washer door open. After opening the door and removing the clothes, I recommend emptying any remaining water in the tub with a wet/dry vacuum (or bail it out). Since you already have the bottom front service panel off and the washer unplugged, you can arrange shallow pans and towels to catch any remaining water and pull the large item filter out of the drain pump assembly as shown in the second image below. You may find a clog in this area that is preventing your washer from draining properly. Clear any clog or debris from this area and reassemble the washer. Check your drain hose