Authentication Error Occurred Printer
Contents |
of and possible solutions for the error messages that are printed on the error logs or reports. Message Cause Solution “84: Error” There is no work area available for image processing. In [Printer Features], under [System], set [Memory Usage] authentication error occurred samsung tablet to [Font Priority]. Decrease the number of files sent to the printer
Authentication Error Occurred Galaxy S5
or install the optional SDRAM module. For details about installing SDRAM module, see Installing the SDRAM module. “85: Error” The authentication error occurred wifi galaxy s3 specified graphics library is unavailable. Check that the data is valid. Decrease the number of files sent to the printer or install the optional SDRAM module. For details about installing SDRAM module, authentication error occurred note 2 see Installing the SDRAM module. “86: Error” Parameters of the control code are invalid. Check the print settings. “91: Error” Printing was canceled by the auto job cancel function due to a command error. Check that the data is valid. “92: Error” Printing was canceled because [Job Reset] or the [Suspended] key was selected on the printer's control panel. Perform the print operation again as
Authentication Error Occurred Wifi Android
necessary. “98: Error” The printer could not access the hard disk correctly. Turn the main power switch off and then back on again. If the message appears frequently, contact your service representative. “Address Book is currently in use by another function. Authentication has failed.” The printer currently cannot perform authentication because the Address Book is being used by another function. Wait a while, and then retry the operation. “Auto-registration of user information has failed.” Automatic registration of information for LDAP Authentication or Windows Authentication failed because the Address Book is full. For details about automatic registration of user information, see Security Guide. “Classification Code is incorrect.” The classification code has not been entered, or the classification code has been entered incorrectly. Enter the correct classification code. “Classification Code is incorrect.” The classification code is not supported by the printer driver. Select Optional for the classification code. For details about how to specify classification code settings, see Registering Classification Codes. “Collate has been cancelled.” Collate was canceled. Decrease the number of files sent to the printer or install the optional SDRAM module. For details about installing SDRAM module, see Installing the SDRAM mo
Start here for a quick overview of the site Help Center Detailed answers to any questions you might have Meta Discuss the workings and policies of this site About Us Learn more about Stack Overflow the company Business Learn more about hiring authentication error occurred wifi galaxy s2 developers or posting ads with us Ask Different Questions Tags Users Badges Unanswered Ask Question authentication error occurred while connecting to wifi _ Ask Different is a question and answer site for power users of Apple hardware and software. Join them; it only takes a minute:
Authentication Error Occurred Note 4
Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the top How to print to a Ricoh Aficio printer requiring authentication? up vote 1 down vote http://support.ricoh.com/bb_v1oi/pub_e/oi_view/0001045/0001045419/view/manual/int/0339.htm favorite 1 I'm trying to configure a lab of OS X workstations to print to a Ricoh Aficio MP C5000. The Aficio is configured to require user authentication (a 4-digit passcode) in order to print. In Mac OS X System Preferences, I've created a printer (LPD connection to the Aficio's IP address). When I print to it, OS X thinks the print job has completed successfully. The job shows up on the Aficio, but immediately has status "Cancelled", with the http://apple.stackexchange.com/questions/61669/how-to-print-to-a-ricoh-aficio-printer-requiring-authentication error log message "You do not have a privilege to use this function. This job has been cancelled". How can I tell OS X to authenticate before sending the print job? (I don't see any field for entering the passcode in the OS X printer settings.) I've already tried: Setting the "User ID" under "Job Log" in the Mac print dialog. Setting the "User Code" under "Job Log" in the Mac print dialog. Setting it up as a Windows printer but OS X is unable to connect to the Aficio using this protocol. Using the Gutenprint driver but that makes no difference. Using IPP instead of LPD, but that makes no difference. All of the above on both Lion and Mountain Lion; neither works. lion mountain-lion printing authentication share|improve this question edited Aug 16 '14 at 3:09 asked Aug 22 '12 at 20:54 smokris 4142612 Does the pin need to be entered on the printer itself? If so there's surely no way around that. –hellothere Aug 22 '12 at 23:44 No — the Windows driver has a field into which you can enter the pin, and print remotely without having to touch the device. I just haven't been able to find a similar setting with the OS X driver. –smokris Aug 22 '12 at 23:47 Does this help... It has something about a Job Log listed as a required step... m.wpi.edu/academics/CCC/Help/Softwa
Hardware Authentication on RICOH Printer + Post New Thread Results 1 to 5 of 5 Hardware Thread, Authentication on RICOH Printer in Technical; Anybody having success using Windows Authentication on a RICOH MFD? We have http://www.edugeek.net/forums/hardware/63927-authentication-ricoh-printer.html the RICOH Aficio MP C3000 that has just ... LinkBack LinkBack URL About LinkBacks Bookmark & Share Digg this Thread!Add Thread to del.icio.usBookmark in TechnoratiTweet this threadShare on Facebook!Reddit! Thread Tools Search Thread Advanced Search 12th October 2010,09:41 AM #1 detjo Join Date Feb 2008 Posts 424 Thank Post 14 Thanked 66 Times in 56 Posts Rep Power 38 Authentication on RICOH Printer Anybody having success using Windows Authentication authentication error on a RICOH MFD? We have the RICOH Aficio MP C3000 that has just been set up with Windows Authentication, and at least 50% of the time authentication fails when logging in at the console. Its on our Win2008 network. I have checked network connections and all is well. Suggestion, anyone? Send PM 12th October 2010,09:44 AM #2 TopBanana Join Date Jul 2010 Location Lowestoft Posts 281 Thank Post 112 Thanked authentication error occurred 32 Times in 28 Posts Rep Power 0 Originally Posted by detjo Anybody having success using Windows Authentication on a RICOH MFD? We have the RICOH Aficio MP C3000 that has just been set up with Windows Authentication, and at least 50% of the time authentication fails when logging in at the console. Its on our Win2008 network. I have checked network connections and all is well. Suggestion, anyone? have a chat with shane hes a member on here see below, he works for Richo tech support and should be able to help you, View Profile: mac_shinobi - EduGeek.net Thanks to TopBanana from: detjo(13th October 2010) 12th October 2010,11:06 AM #3 detjo Join Date Feb 2008 Posts 424 Thank Post 14 Thanked 66 Times in 56 Posts Rep Power 38 Thanks TopBanana! Send PM Thanks to detjo from: TopBanana(12th October 2010) 12th October 2010,06:17 PM #4 mac_shinobi Join Date Aug 2005 Posts 10,341 Thank Post 3,838 Thanked 1,176 Times in 1,069 Posts Rep Power 390 In comparison to the copiers 2008 uses NTLMv2 so maybe worth while - assuming you are ok with it and it is not a security risk change the authentication level to use NTLMv1 or NTLMv2 if negotiated through the security policy on the server ( c