Error Could Not Bind Socket
Contents |
ease planning, as well. Free PRTG Download >> What is this? This knowledgebase contains questions and answers about PRTG Network Monitor and network monitoring in general. You are
Could Not Bind Socket To Port
invited to get involved by asking and answering questions! Learn more Top error binding socket addr='af_unix(/dev/log)' error='address already in use (98)' Tags 5732× prtg 1833× snmp 1463× sensor 933× wmi 622× notifications 463× maps View all Tags Netflow Sensor Error "could
Error Binding Socket Addr='af_inet
not bind socket..." Votes:0 Your Vote: Up Down I had setup netflow on our Cisco ASA and directed traffic to the PRTG server over UDP 2055. The sensor was up and running error binding socket (3420) for about five minutes, then it alarmed with the following error: "Could not bind socket. Address and Port are already in use." I have verified that the ASA is sounding packets with no errors using "sh flow-export counters" command. Running debug I do not see any errors on the ASA itself. I took a quick look at the forums and I did read that a reboot could not bind socket permission denied of the PRTG server may be necessary. I would like to avoid that if possible, we have about 3000 sensors running with no problems, it is just the Netflow sensor that is throwing the error. asa netflow socket-error Created on Sep 20, 2012 4:30:39 PM by mrjoshuaw (0) ●1 Permalink 4 Replies Votes:0 Your Vote: Up Down Hello, you can also restart the PRTG Probe Service, that should suffice as well (not a full restart of the entire machine), but will also cause a short gap in the monitoring. The other thing you can try is setting the port on which the Netflow Sensor listens to 2155 (for example) wait a few minutes, then set it back to 2055. Or pause the sensor for at least 5 minutes. best regards. Add comment Created on Sep 20, 2012 7:43:54 PM by Torsten Lindner [Paessler Support] Permalink Votes:0 Your Vote: Up Down I have the same issue for a customer of ours using PRTG v 12.2.2.2211. >> We created a NetFlow configuration on Cisco Nexus 7000. >> Wireshark on the PRTG server shows the flow packets arriving OK. >> we configured a v9 NetFlow sensor on the p
ease planning, as well. Free PRTG Download >> What is this? This knowledgebase contains questions and answers about PRTG Network Monitor and network monitoring in general.
Could Not Bind Socket On Address Pfsense
You are invited to get involved by asking and answering questions! Learn more prtg could not bind socket Top Tags 5732× prtg 1833× snmp 1463× sensor 933× wmi 622× notifications 463× maps View all Tags "could
Could Not Bind To Socket Php
not bind socket, address and port in use. Votes:0 Your Vote: Up Down so my probe for netflow is not collecting any data and I get the error"could not bind socket, address https://kb.paessler.com/en/topic/41413-netflow-sensor-error-could-not-bind-socket and port in use..I have switched between ports 9991, 2155 and 2055. If I select assign a port and use netlow tester, I get an error..but if I use the tester with a port that is unassigned in the probe, I do not get the error. when I assign the port that I just tested in the netlow 9 tester (without any errors) and https://kb.paessler.com/en/topic/54843-could-not-bind-socket-address-and-port-in-use test again I get the error.. netflow-v9 probes prtg-network-monitor Created on Jul 3, 2013 7:13:36 AM by vtk96 (0) ●1 Permalink 1 Reply Votes:0 Your Vote: Up Down Hello, thank you very much for your KB-Post. It's normal, that when you run the Netflow Tester and a Sensor, to listen on the same UDP Port, only one of them will work. Only one application can listen/bind a port. That's not our limitation, this is Windows. Which exact version of PRTG are you using? Please try restarting the PRTG Probe Service after using the Netflow Tester. Do the sensors then start working? best regards. Add comment Created on Jul 3, 2013 1:03:14 PM by Torsten Lindner [Paessler Support] Permalink Please log in or register to enter your reply. Disclaimer: The information in the Paessler Knowledge Base comes without warranty of any kind. Use at your own risk. Before applying any instructions please exercise proper system administrator housekeeping. You must make sure that a proper backup of all your data is available. © 1998 - 2016 Paessler AG Solutions • Imprint • Contact • Sitemap • Privacy Policy • Uninstall • Terms
you either log on to your computer or when you open X-Charge. Resolution You may see the following error when trying to open X-Charge from the File menu. To correct this could not issue and make sure the error does not reappear: Have all users exit out of X-Charge Open Task Manager, and End Process on all running XChrgSvr.exe processes (there may be several). Open Control Panel > could not bind Administrative Tools > Services Look for XCharge Server in the list, and verify that it is set to Automatic If it is not, right-click on it, and change the Startup Type to Automatic Start the service You should now be able to open X-Charge from all users without getting the error message. Submitted by Heath May 20, 2016 23:50 Was this article helpful? 0 out of 0 found this helpful Facebook Twitter LinkedIn Google+ Have more questions? Submit a request Comments Related articles Scheduler Settings How do I Add/Edit Users in X-Charge? Please stop by our website: GTSservices.com Powered by Zendesk