Eio Service Error
Contents |
/ Network card. 3, Replace Network card. 3. Replace the formatter board. HP LASER PRINTERS 1200, 2200, 3100, 3150 FAX, 3200 FAX, 4100 1. Temporary Printer error. Disconnect the power cable from the eio 2 error product, wait at lest 30 seconds, reconnect the power cable, and then wait for the eio 2 error hp laserjet 4100n product to initialize. 2. If error persists replace the formatter board. HP LASER PRINTER 2300, 2410, 2420, 2430 ERROR 8X.YYY EIO ERROR1. eio 2 error hp laserjet 4200 The EIO accessory card has encountered a critical error. X resents the error location, YYYY represents the error code. 2. Turn the printer power off, and then turn the printer power on.3. Turn the printer power
82.0180 Eio 2 Error 4200
off, reseat the EIO accessory in slot X, and then turn the printer on.4. Turn the printer power off, install it in a different EIO slot, and turn the printer power on.5. Replace the EIO accessory in slot X HP LASER PRINTER P3005, 3027M, 3035 ERROR 8X.YYYY1. The EIO accessory card has encountered a critical error.2. Turn the device off and then on.3. Upgrade the Jetdirect firmware.4. Try to determine whether the error occurs eio 1 error intermittently, while printing, or when turning on the device.5. If the error appears while printing, determine whether it occurs when printing from a specific computer, a specific application, or a specific file. If all other computers, applications, or files can print without the error, then the problem maybe only within one print job or computer. Make sure the computer has the most current printer drivers, or use a generic printer driver.6. If the error occurs when the device is first turned on, turn off the device, disconnect the LAN cable, and then turn on the device. This process will determine if errors occur from the network connection, If errors do not appear when the LAN cable is unplugged, it is possible traffic or signal on the network might be causing the error. Make sure to try all solutions suggested, especially upgrading the Jetdirect firmware.7. Disable the print server, For EIO print servers, remove the card. For embedded print servers, use the SERVICE menu.8. if the problem persists, contact HP Support. HP LASER PRINTER 3200 1. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize.2. If the error persists, replace the formatter. HP LASER PRINTER 4200, 4300, 4250, 4350 ERROR 8X.YYYY 1. The EIO
Printer Error Codes and Support Error: 80 SERVICE http://www.advancedlaser-hp-error-codes.com/error_80.htm (XXXX)EIO ERROR Error Description: A critical EIO failure has occurred. X indicates the slot number of the device. XXXX indicates the error type. Solution: https://www.orionmarket.com/product_error/8540/HP/HP-4550/80-service-xxxxeio-error/ 1. Turn the printer off and on to reset the printer. 2. Reseat the EIO card. 3. Replace the EIO card. Call for Assistance 877-755-5300 Home About Us Contact Us Search Site Map Printers Supplies Accessories Parts Error Codes Login Shopping Cart Return Policy Privacy Policy Orion Printers and Parts 6030 Marshalee Dr. #257 Elkridge, Maryland 21075 (410) 540-9090 (877) 755-5300 © 2016 Orion Contracting Services. All Rights Reserved.
Account Login Shopping Cart My Account Checkout Home Troubleshooting HP Error Codes Numeric Error Codes 20 - 49 (HP LaserJet) Email HP LaserJet Error Codes 20 - 49 Below are error codes for the HP LaserJet series, for codes ranging from 20-49. Please note the explanations are general descriptions for ALL http://www.printertechs.com/printer-troubleshooting/hp-error-codes/192-numeric-error-codes-20-49-hp-laserjet LaserJets, often more detailed info will be available if you search for a specific error https://www.cnet.com/forums/discussions/on-start-up-315144/ code on a specific model (e.g. "50.9 error LaserJet 3000") Have a question? Call us 608-831-2396 for more information. Message on printer displayWhat it meansWhat to do 20 INSUFFICIENT MEMORY The printer received more data than can fit in available memory. You may be trying to print a document that is too complex for the printer's capacity (too many macros, soft eio 2 fonts, or graphics). Pressing GO may print the transferred data, but data may be missing or skewed. If the file size of the print job exceeds printer's onboard memory capacity, try adding more memory. Sometimes mismatched software drivers over-inflate the size of a document and cause these errors; you may want to download/install a different driver. If all else fails, simplify the print job and print manageable segments at a time. 21 PAGE TOO COMPLEX The eio 2 error data (dense text, rules, raster or vector graphics) sent to the printer is too complex Pressing GO may print the transferred data; but some data may be missing or skewed. More memory may help. You can also try a different driver, or simplify the print job by breaking it up into manageable segments. 40 EIO x BAD TRANSMISSION The connection has been broken between the printer and the EIO card in the specified slot. (Data loss might occur in this situation.) 1. Press GO to clear the error message and continue printing. 2. Reseat the EIO card in slot corresponding to [X]. 3. Check cabling. 4. Replace the network card if needed. 5. Try a different software driver. 41.3 UNEXPECTED PAPER SIZE The printer detected a media size different from what it was expecting. This is typically caused if two or more sheets stick together in the printer or if the tray is not properly adjusted. 1. Reload the tray with the correct print media size. 2. Ensure that media in the tray is loaded under the front and back retaining tabs. 3. If you are printing from tray 1, verify that the correct paper size is selected in the control panel. 4. If you are printing from tray 2, 3, or 4, verify that any paper-size adjustments (length guide, width guide, size-selector switch) on the
Popular Forums Computer Help Computer Newbies Laptops Phones TVs & Home Theaters Networking & Wireless Windows 7 Windows 10 Cameras All Forums News Top Categories Apple Computers Crave Deals Google Internet Microsoft Mobile Photography Security Sci-Tech Tech Culture Tech Industry Photo Galleries Video Forums Video Top Categories Apple Byte Carfection CNET Top 5 CNET Update Googlicious How To Netpicks Next Big Thing News On Cars Phones Prizefight Tablets Tomorrow Daily CNET Podcasts How To Top Categories Appliances Computers Gaming Home Entertainment Internet Mobile Apps Phones Photography Security Smart Home Tablets Wearable Tech Forums Speed Test Smart Home Top Categories Tour CNET Smart Home Smart Home News Smart Home How To Best Smart Home Devices Cars Top Categories Car Reviews Best Cars New Cars Used Cars Deals Top Categories Cheapskate Best Tech Under $50 All Deals Tech Deals Non-Tech Deals Audio Deals Cell Phone Deals Desktop Deals Laptop Deals Hard Drive & Storage Deals Printer Deals Tablet Deals Camera Deals Monitor Deals Software Deals TV Deals Web Hosting VPN Services WordPress Hosting Domain Names Download Sign In / Join Sign In to CNET Join CNET Member Benefits My Profile Forums Sign Out US Other editions United Kingdom Australia China France Germany Japan Korea CNET en Español CNET Forums Windows Legacy OS On start-up Windows Legacy OS forum About This ForumCNET's Forum on Windows legacy operating systems, (XP, 2000/NT, ME, & Windows 95/98) is the best source for finding help or getting troubleshooting advice from a community of experts. Discussions cover Windows 2003 Server, Windows installation, adding and removing programs, driver problems, crashes, upgrading, and other OS-related questions.Real-Time ActivityMy Tracked DiscussionsFAQsPoliciesModerators General discussion On start-up by jims-in / November 4, 2008 9:12 PM PST When starting the pc when windows ?XP loads I get this messagestartservice cannot create a file when that file already existsI then click ok (that?s the only option) then I get this messageCan't Start Kernel Mode Driver ServiceIn Event Properties, I have this in systemEventDate 05/11/2008 Source: Service command managerTime: 12:35 Category: NoneType: Error Event: ID 7000User: N/ADesciptionThe EIO service failed to start due to the following error: Cannot create a file when that file already exists. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.I?m looking for an explanation and of course a fix to this plese.Thank yo