Hp Laserjet 4050 Eio 2 Error
Contents |
R2 Deployment Straight in the Deep End - Learning SCCM 2012 R2 from Scratch and Deploying in a Production Environment. New office building and server room Planning new server room in a new building for one
Eio 2 Error Hp Laserjet 4200
of our clients. Server hardware refresh Remove old server hardware and virtualize the servers TECHNOLOGY IN eio accessory THIS DISCUSSION Join the Community! Creating your account only takes a few minutes. Join Now What could cause an HP LaserJet 4050tn printer
Eio Card
to display an "87.0007 EIO 2 Error"? It could be a co-incidence that this error began displaying a few days ago after I set Spiceworks to start doing scheduled inventory scans. I don't believe it is the result of 82.0180 eio 2 error hp 4050 a scheduled Spiceworks inventory scan because it doesn't happen when the rescan link for the device is clicked. Any thoughts? Reply Subscribe View Best Answer RELATED TOPICS: HP Laserjet 3015 Error 49.4C02 HP Laserjet 600 m602 error HP Laserjet 2200 getting error 40 EIO   4 Replies Cayenne OP Helpful Post SJLyons50 Aug 21, 2009 at 7:55 UTC Just checked with Google and found a similar problem on HP's IT Resources Center website, back in 2005. In hp laserjet 4000 eio 2 error this particular case, the problem was found to be caused by excessive SNMP network scan! Link to entry: http://forums11.itrc.hp.com/service/forums/questionanswer.do?admit=109447626+1250858300687+28353475&threadId=917513 Regards, Steve. 0 Ghost Chili OP Best Answer Curtis3363 Aug 21, 2009 at 8:02 UTC Turn off the printer. Turn on the printer. Reseat the EIO board. It might be possible to upgrade the EIO card firmware, although sometimes it is not possible to connect to it when the printer is in an error condition. Contact a network administrator. NOTE: If the steps listed in this document do not return the printer to a READY state, service may be required. Contact the HP Customer Care Center for more information. The EIO accessory in slot X has encountered a critical error as specified by YYYY. X Description: 1 = EIO slot 1 - The printer detected an error with the EIO card. 2 = EIO slot 2 - The printer detected an error with the EIO card. 6 = EIO slot 1 - The EIO card detected an error. 7 = EIO slot 2 - The EIO card detected an error. 0 Cayenne OP Richard Cranium Sep 1, 2009 at 3:14 UTC I would second that. Reseat the EIEIO cards and update the firmware. We have a few 4050's on the network and they run fine with spiceworks. If you find the card has gone bad,
by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you
82.0180 Eio 2 Error Hp Laserjet 4300
need to. 100% Satisfaction Guarantee Rate the answer you receive. Ask Wendell Huneycutt error 82.0180 hp 4000 Your Own Question Wendell Huneycutt, Technician Category: Printers Satisfied Customers: 111 Experience: All print technologies and almost all major
Hp Jetdirect 620n
manufacturers. HP Certified Professional and CompTIA PDI+ Certification. 62381604 Type Your Printers Question Here... Wendell Huneycutt is online now HP LaserJet 4000. Getting an 82.0180 EIo 2 Error. The Computer This https://community.spiceworks.com/topic/75479-laserjet-4050tn-87-0007-eio-2-error answer was rated: ★ ★ ★ ★ ★ HP LaserJet 4000. Getting an 82.0180 EIo 2 Error. The Computer indicates the printer is off line. Cannot find solution in manuel. Share this conversation Expert: Wendell Huneycutt replied4 years ago. Wendell Huneycutt : Hello, my name is XXXXX XXXXX I want to do everything possible to resolve your problems! Good Morninig! This error is http://www.justanswer.com/printers/5rp83-hp-laserjet-4000-getting-82-0180-eio-error-computer.html refering to a failure of the EIO device plugged into slot #2 on the back of your printer. Either a JetDirect card (NIC) or a hard drive. If you are using an Ethernet card, power off the printer and remove the device from slot 2 (they are marked) then power on and see if code is gone. If the code clears, then power off and put the card into slot 1 and repower on. If the code reappears, the card is bad and will need to be replaced. Special note: the JetDirect 615 card is notorius for failing. The best place to buy a new one (non 615) is Ebay. Please keep me informed and we will get your problem resolved! Thanks!!Wendell Huneycutt : Your positive feedback is exceedingly important to me. If you feel that you have received value for your money and a resolution for your problem I ask that you please select the green “ACCEPT” button. If I have not met your expectations or resolved your issue, PLEASE continue to work with me for the resolution and value you are looking for. I am a professional t
Hottest Threads / Posts Forum Rules What's New? Advanced Search Forum Technical Forums Fax & Printer Technical Discussion HP HP LaserJet 4200dtn network http://www.copytechnet.com/forums/hp/80325-hp-laserjet-4200dtn-network-error-82-0180-a.html error 82.0180 If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. Page 1 of 2 12 Last Jump to eio 2 page: Results 1 to 10 of 13 Thread: HP LaserJet 4200dtn network error 82.0180 Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode 08-14-2013 #1 wseyller View Profile View Forum Posts Private Message Field Supervisor 1,000+ Posts Join Date Sep 2012 Posts 1,106 Post Thanks / Like eio 2 error Thanks (Given) 2 Thanks (Received) 83 Likes (Given) 4 Likes (Received) 125 Dislikes (Given) 0 Dislikes (Received) 0 Rep Power 23 HP LaserJet 4200dtn network error 82.0180 This printer is at a bank and all their print drivers are installed on a server at a different location. All printers pull a reserved ip address from their dhcp server eveytime the network is initialized. Also ports are designated for each device. The office person was out and their computer was off so I could not personally try test prints. When I arrived to this printer it had a message saying Processing that it was stuck on. I rebooted and it got all the way to "Cartridge Installed" and it would not go away. Would not respond to key presses and shows a steady green Ready light. Removing the cartridge made no change but motor would cycle after closing door. 2nd reboot same thing except the Data light was steady green as well. Removed lan cable and all accessories and it would boot ok. Then after a few seconds of inserting