Laserjet 4000 Eio 2 Error
Contents |
Creating your account only takes a few minutes. Join Now What could cause an HP LaserJet 4050tn printer to display an "87.0007 EIO 2 Error"? It could be a co-incidence that
Eio 2 Error Hp Laserjet 4200
this error began displaying a few days ago after I set Spiceworks to start doing eio accessory scheduled inventory scans. I don't believe it is the result of a scheduled Spiceworks inventory scan because it doesn't happen when the
Eio Card
rescan link for the device is clicked. Any thoughts? Reply Subscribe View Best Answer RELATED TOPICS: HP Laserjet 3015 Error 49.4C02 HP Laserjet 600 m602 error HP Laserjet 2200 getting error 40 EIO   4 Replies 82.0180 eio 2 error hp 4050 Cayenne OP Helpful Post SJLyons50 Aug 21, 2009 at 7:55 UTC Just checked with Google and found a similar problem on HP's IT Resources Center website, back in 2005. In this particular case, the problem was found to be caused by excessive SNMP network scan! Link to entry: http://forums11.itrc.hp.com/service/forums/questionanswer.do?admit=109447626+1250858300687+28353475&threadId=917513 Regards, Steve. 0 Ghost Chili OP Best Answer Curtis3363 Aug 21, 2009 at 8:02 UTC Turn off the printer. 82.0180 eio 2 error hp laserjet 4300 Turn on the printer. Reseat the EIO board. It might be possible to upgrade the EIO card firmware, although sometimes it is not possible to connect to it when the printer is in an error condition. Contact a network administrator. NOTE: If the steps listed in this document do not return the printer to a READY state, service may be required. Contact the HP Customer Care Center for more information. The EIO accessory in slot X has encountered a critical error as specified by YYYY. X Description: 1 = EIO slot 1 - The printer detected an error with the EIO card. 2 = EIO slot 2 - The printer detected an error with the EIO card. 6 = EIO slot 1 - The EIO card detected an error. 7 = EIO slot 2 - The EIO card detected an error. 0 Cayenne OP Richard Cranium Sep 1, 2009 at 3:14 UTC I would second that. Reseat the EIEIO cards and update the firmware. We have a few 4050's on the network and they run fine with spiceworks. If you find the card has gone bad, I recommend Depot America for replacement LJ Parts. 0 Ghost Chili OP Curtis3363 Sep 1, 2009 at 3:19 UTC If the cards are locked
by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask
Hp Laserjet 4000 Eio 2 Error
follow up questions if you need to. 100% Satisfaction Guarantee Rate error 82.0180 hp 4000 the answer you receive. Ask Ryan B. Your Own Question Ryan B., Support Specialist Category: Computer Satisfied Customers:
Hp Jetdirect 620n
1775 Experience: Comptia A+ Certified Technician , with 8+ years Experience 16548393 Type Your Computer Question Here... Ryan B. is online now Error message 82.0180 EIO 2. What is https://community.spiceworks.com/topic/75479-laserjet-4050tn-87-0007-eio-2-error this error and how can Customer Question Error message: 82.0180 EIO 2. What is this error and how can we fix it? Submitted: 5 years ago. Category:Computer Share this conversation Expert: Ryan B. replied5 years ago. Ryan B. : Hello and welcome to JustAnswer~! My name is Ryan and I would like to assist you with your question.Ryan http://www.justanswer.com/computer/4y211-error-message-82-0180-eio-2-error.html B. : Are you using a JetDirect?Ryan B. : I'm going to assume you are using one, you can try to Reseat the jetdirect card on a different slot and see whether the issue still persist. Chances are you may need to get a new JetDirect Card thoughRyan B. : What is the make/model of your device?JACUSTOMER-99s6rsxu- : Not sure if we're using a JetDirect or not. How do I reseat the jetdirect card?Ryan B. : what is the make/model of your device?JACUSTOMER-99s6rsxu- : It is a HP 4300 dtns Ryan B. : Turn off the printer, remove the HP Jetdirect print server, andturn the printer back on. If the error message disappears whenthe print server is removed, it is likely that the print serverwas causing the error. Replace the print server.Ryan B. : The following are sample images. Your printer may have the JetDirect network card in a different location.Full Size ImageRyan B. : Turn off the printer and disconnect the printer’s power cable. Locate where the network cable is a
Hottest Threads / Posts Forum Rules What's New? Advanced Search Forum Technical Forums Fax & Printer Technical Discussion HP HP LaserJet 4200dtn network error 82.0180 If this is your first visit, be sure to check out the FAQ by http://www.copytechnet.com/forums/hp/80325-hp-laserjet-4200dtn-network-error-82-0180-a.html clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. Page 1 of 2 12 Last Jump to page: Results 1 to 10 of 13 Thread: HP LaserJet 4200dtn network error 82.0180 Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… Display Linear Mode Switch to Hybrid Mode eio 2 Switch to Threaded Mode 08-14-2013 #1 wseyller View Profile View Forum Posts Private Message Field Supervisor 1,000+ Posts Join Date Sep 2012 Posts 1,107 Post Thanks / Like Thanks (Given) 2 Thanks (Received) 83 Likes (Given) 4 Likes (Received) 126 Dislikes (Given) 0 Dislikes (Received) 0 Rep Power 23 HP LaserJet 4200dtn network error 82.0180 This printer is at a bank and all their print drivers are installed on a server at a different location. All eio 2 error printers pull a reserved ip address from their dhcp server eveytime the network is initialized. Also ports are designated for each device. The office person was out and their computer was off so I could not personally try test prints. When I arrived to this printer it had a message saying Processing that it was stuck on. I rebooted and it got all the way to "Cartridge Installed" and it would not go away. Would not respond to key presses and shows a steady green Ready light. Removing the cartridge made no change but motor would cycle after closing door. 2nd reboot same thing except the Data light was steady green as well. Removed lan cable and all accessories and it would boot ok. Then after a few seconds of inserting lan cable it will show Processing forever. One time after booting without the network cable I tried to print a config page. 1st page came out then it was just stuck with the message "Printing Configuration". Other times this did not happen. Config page shows error 82.0180 which is a network error. Also I saw this error come up one time while I was there. Printer has 615N jetdirect card and I tried installing it from EIO 2 to 1. Printer will not boot all the way and get stuck on "***************". Put card back into slot