678 Error Pppoe
Contents |
Ethernet & T1 Service trueSTREAM Business Standard DSL Hosted Voice Service Website Hosting SUPPORT SUPPORT Where are you? Support > error 678 reliance netconnect Knowledge Base > DSL Support > Dynamic IP > Windows XP PPPoE Client Error 678
How To Fix Error 678 Windows Xp
Windows XP PPPoE Client Error 678 Print Windows XP PPPoE Client Error 678Error 678 is the error code that indicates the remote computer error 678 dial up did not respond. This error code is rather difficult to troubleshoot since there can be many things that cause this error. Follow the instructions below to troubleshoot an error 678.1. Verify that the modem is in sync. The error 678 the remote computer did not respond modems sync light (Ready/DSL/Line) should be solid green or solid amber (in the case of a broadmax modem). If the modem is not in sync refer to the check sync knowledge base heading or call into tech support to troubleshoot the problem.2. Verify that there is a solid Ethernet connection between the computer and the modem. A solid connection is indicated by a green link light (labeled link/enet/LAN). Often the link light will blink when there is Ethernet
Error 678 Windows 7
activity between the modem and the PC. If the link light is not on then unplug both ends of the cable and plug them back in, this will "reseat" the cable. If you are still unable to get a link light call into tech support at 866-491-7221 in order to receive further assistance with this issue.3. Make sure that there is no router involved. A router will cause this error every time. If you are using a router you do not need to use the windows XP PPPoE client, however you must set the router to PPPoE authentication. This is covered in the router setup knowledge base article.4. Turn the modem off for 10-15 seconds and t hen turn it back on. When the sync light (Ready/Line/DSL) is solid attempt to reconnect. If your modem does not have a power switch simply unplug the power cable.5. Ensure that the line is properly filtered. Make sure that all phone devices on the line have ADSL Micro Filters installed on them, make sure that there is no ADSL micro filter on the DSL modem. If all filters are correctly installed and you still receive this error the next step is to isolate the line. Do this by removing all phone devices from the line except for the DSL modem, and then attempt to reconnect.6. Are there any software firewalls enabled (Zone Al
Ethernet & T1 Service trueSTREAM Business Standard DSL Hosted Voice Service Website Hosting SUPPORT SUPPORT Where are you? Support > Knowledge Base > DSL Support > Dynamic IP error 678 in bsnl broadband > Windows XP PPPoE Client Error 678 Windows XP PPPoE Client Error 678 Print Windows error 678 tata photon XP PPPoE Client Error 678Error 678 is the error code that indicates the remote computer did not respond. This error code is rather difficult to troubleshoot
Error 678 Modem
since there can be many things that cause this error. Follow the instructions below to troubleshoot an error 678.1. Verify that the modem is in sync. The modems sync light (Ready/DSL/Line) should be solid green or solid amber (in the case of https://www.dslextreme.com/support/kb/dsl-support/dynamic-ip/windows-xp-pppoe-client-error-678 a broadmax modem). If the modem is not in sync refer to the check sync knowledge base heading or call into tech support to troubleshoot the problem.2. Verify that there is a solid Ethernet connection between the computer and the modem. A solid connection is indicated by a green link light (labeled link/enet/LAN). Often the link light will blink when there is Ethernet activity between the modem and the PC. If the link light is not on then unplug both ends of the cable and https://www.dslextreme.com/support/kb/dsl-support/dynamic-ip/windows-xp-pppoe-client-error-678 plug them back in, this will "reseat" the cable. If you are still unable to get a link light call into tech support at 866-491-7221 in order to receive further assistance with this issue.3. Make sure that there is no router involved. A router will cause this error every time. If you are using a router you do not need to use the windows XP PPPoE client, however you must set the router to PPPoE authentication. This is covered in the router setup knowledge base article.4. Turn the modem off for 10-15 seconds and t hen turn it back on. When the sync light (Ready/Line/DSL) is solid attempt to reconnect. If your modem does not have a power switch simply unplug the power cable.5. Ensure that the line is properly filtered. Make sure that all phone devices on the line have ADSL Micro Filters installed on them, make sure that there is no ADSL micro filter on the DSL modem. If all filters are correctly installed and you still receive this error the next step is to isolate the line. Do this by removing all phone devices from the line except for the DSL modem, and then attempt to reconnect.6. Are there any software firewalls enabled (Zone Alarm, Norton Internet Security, McAfee Personal Firewall)? Firewalls can cause the connection to fail. If you have any software firewalls enabled disable them and attempt to connect again.7. Recreating the PPPoE "dialer" can solve this error. Go to start>control panel>network connections. In Network connections de
not respond.” Broadband connections If this error occurs with a broadband connection, it could be because of the following reasons: The http://www.tech-faq.com/error-678.html network cable to the machine may have been unplugged. The modem connecting http://forums.mozillazine.org/viewtopic.php?f=38&t=518107 to the Internet may be disabled or its drivers may be corrupt. Spyware. The TCP/IP stack on the computer is corrupt and needs repair. A third party firewall software is erroneously preventing the user from connecting to the Internet. The options below will help users to get around this issue: error 678 Ensure that the network cable is correctly connected and that the cable is not damaged. Also ensure that the network adapter is enabled. To do this, click Start, Run and type ncpa.cpl, and click OK. After right clicking the Local Area Connection icon, click ‘Enable’ if it is available. Try restarting both the computer and the modem. After rebooting, wait until all applications error 678 windows and services have finished loading. After that, try the connection again. If using Windows XP, use the netsh command to reset the tcp/ip interfaces. Click Start then select Run. In the box that appears, type ‘cmd’ and click the OK button. When the command window appears, type ‘netsh interface ip reset log.txt’ and hit the enter button. Type ‘exit’ at the command prompt and hit the enter button. Restart the computer and try again. Try reinstalling the modem and its drivers. Use a good anti-spyware tool to get rid of spyware and/or adware that may be hindering a good Internet experience. Powerful firewall programs such as ZoneAlarm can cause the Error 678 to appear during their operation. To try isolating the problem, uninstall the firewall program and test the machine. If the program is indeed causing the issue, contact its technical support for a solution. VPN Connections in Windows 2000 If using Windows 2000 and getting error 678 when opening a VPN connection, a hotfix is needed. Download the most recent service pack from Microsoft and install it. If the problem persists, contact Microsoft for support
mozillaZine is an independent Mozilla community and advocacy site. We're not affiliated or endorsed by the Mozilla Corporation but we love them just the same. Proudly Powered by phpBB © phpBB Group © 1998-2015 mozillaZine All Rights Reserved