Adsl Error 678
Contents |
Ethernet & T1 Service trueSTREAM Business Standard DSL Hosted Voice Service Website Hosting SUPPORT SUPPORT Where are you? Support > Knowledge Base > DSL Support > Dynamic how to fix error 678 windows xp IP > Windows XP PPPoE Client Error 678 Windows XP PPPoE Client Error 678 Print error 678 reliance netconnect Windows XP PPPoE Client Error 678Error 678 is the error code that indicates the remote computer did not respond. This error code is rather difficult error 678 pppoe to troubleshoot since there can be many things that cause this error. Follow the instructions below to troubleshoot an error 678.1. Verify that the modem is in sync. The modems sync light (Ready/DSL/Line) should be solid green or solid amber (in the error 678 dial up case of a broadmax modem). If the modem is not in sync refer to the check sync knowledge base heading or call into tech support to troubleshoot the problem.2. Verify that there is a solid Ethernet connection between the computer and the modem. A solid connection is indicated by a green link light (labeled link/enet/LAN). Often the link light will blink when there is Ethernet activity between the modem and the PC. If the link light is not on then unplug both ends of
Error 678 The Remote Computer Did Not Respond
the cable and plug them back in, this will "reseat" the cable. If you are still unable to get a link light call into tech support at 866-491-7221 in order to receive further assistance with this issue.3. Make sure that there is no router involved. A router will cause this error every time. If you are using a router you do not need to use the windows XP PPPoE client, however you must set the router to PPPoE authentication. This is covered in the router setup knowledge base article.4. Turn the modem off for 10-15 seconds and t hen turn it back on. When the sync light (Ready/Line/DSL) is solid attempt to reconnect. If your modem does not have a power switch simply unplug the power cable.5. Ensure that the line is properly filtered. Make sure that all phone devices on the line have ADSL Micro Filters installed on them, make sure that there is no ADSL micro filter on the DSL modem. If all filters are correctly installed and you still receive this error the next step is to isolate the line. Do this by removing all phone devices from the line except for the DSL modem, and then attempt to reconnect.6. Are there any software firewalls enabled (Zone Alarm, Norton Internet Security, McAfee Personal Firewall)? Firewalls can cause the connection to fail. If you have any software firewalls enabled disable them and attempt to connect again.7. Recreating the PPPoE "dialer" can solve this error. Go to start>
631 - The port was disconnected by the user Error 633 - The port is already in use / not configured for Remote Access Error 645 - Internal Authentication Error Error 651 -
Error 678 Windows 7
Your modem has reported an error Error 678 - The computer you are dialling error 678 in bsnl broadband into is not answering Error 680 - No dial tone Error 691 - Access denied : username / password is invalid error 678 dial up windows 7 on the domain Error 797 - The modem or other connecting device failed Error 619 - The port was disconnected This error can be resolved by following these steps: · Restart your computer and https://www.dslextreme.com/support/kb/dsl-support/dynamic-ip/windows-xp-pppoe-client-error-678 wait until all applications have completely loaded before trying to reconnect. · Check your modem and phone cables are connected securely. · If your problem has still not been resolved uninstall and reinstall your Broadband modem. For information on how to do this please refer to the ADSL modem setup instructions or the installation cd that was provided with your modem Error 629 - The port was disconnected https://www.resource-utilities.com/adsl_common_errors.aspx by the local machine This can be resolved by following these steps: · Restart your computer and wait until all applications have completely loaded before trying to reconnect. · If your problem has still not been resolved uninstall and reinstall your Broadband modem. For information on how to do this please refer to the ADSL modem setup instructions or the installation cd that was provided with your modem Error 631 -The port was disconnected by the user Usually this is a one-off glitch which happens when the Connection Progress is interrupted by the user or another program on the PC. In order to resolve this: · Restart your computer and wait until all applications have completely loaded before trying to reconnect. Error 633 -The port is already in use / not configured for Remote Access Dialout This error can be best remedied by: · A restart of your computer tends to resolve 50% of cases with this error message · Disable any Firewall Software and try to connect again... · Try uninstalling and reinstalling the Modem. For information on how to do this please refer to the ADSL modem setup instructions or the installation cd that was provided with your modem. Error 645 -
IP isWhoisCalculatorTool PointsNewsNews tip?ForumsAll ForumsHot TopicsGalleryInfoHardwareAll FAQsSite FAQDSL FAQCable TechAboutcontactabout uscommunityISP FAQAdd ISPISP Ind. ForumsJoin Search similar:HVAC products - why no prices?2015 Q1 Subs down[Internet] Looking for advice with 25/10 problems[General] Earthlink DSL QuestionsBusiness Changing to Cablevision Part II[Speed Problem] AT&T merriment or cruelty ? Forums → US ISPs non-cable → Earthlink DSL → [Modem] Error 678 - Remote http://www.dslreports.com/forum/r20145786-Modem-Error-678-Remote-computer-does-not-respond computer does not respond uniqs10006 Share « Me Too - Earthlink you're fired!!! • Anyone having any problems on NYCMNY83.covad.net? » LadyMin@xo.net LadyMin Anon 2008-Mar-11 11:12 am [Modem] Error 678 - Remote computer does not respondI have had a mostly solid DSL line with Earthlink for 7 years. Last Monday I could not connect to the internet. I disconnected my router, UPS and filters and set up a direct connection and used XP's WinPoet error 678 to try to login. Now I get Error 678. I also tried a different phone jack, swapped out phone lead and ethernet cables, and even tried it with my notebook computer.Called Earthlink tech support. Told them all of the above, which they ignored. They had me doing the same troubleshooting again and again and again until finally Saturday they said it was a line problem and would have the phone company work on it. Yesterday error 678 windows they called me and said it was repaired and that it was something in the CO.It is not fixed. I still get Error 678. The tech now tells me it's my modem and that I need a new one. I'm not sure I believe them. How did I go from "the phone company fixed it" to "it's your modem". Plus past experience: They said my modem was bad 2 years ago and it ended up being a line problem. In addition, I have a backup modem (same model), which also gets error 678.My question is this: Is there a way to test the modem? I use a Speedstream 5260. (It's one that should be upgradeable to a 5660, but I have not been able to get it to ftp the upgrade firmware.) I can telnet into it, but I'm not sure how to interpret the results.I asked the earthlink tech if we could test the modem, and he said no, it was too old, the firmware was probably worn out. His exact words, "worn out". Then he went into a sales pitch on buying a new modem or signing a year contract. I will not do that so my options are to solve the problem myself or go with a different ISP.Any help is appreciated. I have run out of patience. Eight days