Connection Problem Error 678
Contents |
Ethernet & T1 Service trueSTREAM Business Standard DSL Hosted Voice Service Website Hosting SUPPORT SUPPORT Where are you? error 678 adsl connection problem xp Support > Knowledge Base > DSL Support > Dynamic IP > Windows XP PPPoE Client
Connection Failed With Error 678
Error 678 Windows XP PPPoE Client Error 678 Print Windows XP PPPoE Client Error 678Error 678 is the error code that indicates how to fix error 678 the remote computer did not respond. This error code is rather difficult to troubleshoot since there can be many things that cause this error. Follow the instructions below to troubleshoot an error 678.1. Verify that the modem error 678 verizon is in sync. The modems sync light (Ready/DSL/Line) should be solid green or solid amber (in the case of a broadmax modem). If the modem is not in sync refer to the check sync knowledge base heading or call into tech support to troubleshoot the problem.2. Verify that there is a solid Ethernet connection between the computer and the modem. A solid connection is indicated by a green link light (labeled link/enet/LAN). Often the link
Error 678 Dial Up
light will blink when there is Ethernet activity between the modem and the PC. If the link light is not on then unplug both ends of the cable and plug them back in, this will "reseat" the cable. If you are still unable to get a link light call into tech support at 866-491-7221 in order to receive further assistance with this issue.3. Make sure that there is no router involved. A router will cause this error every time. If you are using a router you do not need to use the windows XP PPPoE client, however you must set the router to PPPoE authentication. This is covered in the router setup knowledge base article.4. Turn the modem off for 10-15 seconds and t hen turn it back on. When the sync light (Ready/Line/DSL) is solid attempt to reconnect. If your modem does not have a power switch simply unplug the power cable.5. Ensure that the line is properly filtered. Make sure that all phone devices on the line have ADSL Micro Filters installed on them, make sure that there is no ADSL micro filter on the DSL modem. If all filters are correctly installed and you still receive this error the next step is to isolate the line. Do this by removing all phone devices from the line except for the DSL mod
not respond.” Broadband connections If this error occurs with a broadband connection, it could be because of the following reasons: The network cable to the machine may have been unplugged. The error 678 sprint modem connecting to the Internet may be disabled or its drivers may be corrupt. error 678 pppoe Spyware. The TCP/IP stack on the computer is corrupt and needs repair. A third party firewall software is erroneously preventing the user
Verizon Aircard Error 678
from connecting to the Internet. The options below will help users to get around this issue: Ensure that the network cable is correctly connected and that the cable is not damaged. Also ensure that the network https://www.dslextreme.com/support/kb/dsl-support/dynamic-ip/windows-xp-pppoe-client-error-678 adapter is enabled. To do this, click Start, Run and type ncpa.cpl, and click OK. After right clicking the Local Area Connection icon, click ‘Enable’ if it is available. Try restarting both the computer and the modem. After rebooting, wait until all applications and services have finished loading. After that, try the connection again. If using Windows XP, use the netsh command to reset the tcp/ip interfaces. Click Start then select Run. In http://www.tech-faq.com/error-678.html the box that appears, type ‘cmd’ and click the OK button. When the command window appears, type ‘netsh interface ip reset log.txt’ and hit the enter button. Type ‘exit’ at the command prompt and hit the enter button. Restart the computer and try again. Try reinstalling the modem and its drivers. Use a good anti-spyware tool to get rid of spyware and/or adware that may be hindering a good Internet experience. Powerful firewall programs such as ZoneAlarm can cause the Error 678 to appear during their operation. To try isolating the problem, uninstall the firewall program and test the machine. If the program is indeed causing the issue, contact its technical support for a solution. VPN Connections in Windows 2000 If using Windows 2000 and getting error 678 when opening a VPN connection, a hotfix is needed. Download the most recent service pack from Microsoft and install it. If the problem persists, contact Microsoft for support here. NOTE: Microsoft may charge for their assistance. Dial-up Systems Error 678 generally means that the line is ringing, but the remote system is not answering the call. Check the number being called and verify that the number is correct. If using an external modem, turn on the speaker to listen to the connection using the toggle switches on t
List Welcome Guide More BleepingComputer.com → Hardware → External Hardware Javascript Disabled Detected You currently have javascript disabled. Several functions may not work. Please re-enable javascript to http://www.bleepingcomputer.com/forums/t/529177/error-678-usb-external-20-modem/ access full functionality. Register a free account to unlock additional features at BleepingComputer.com Welcome to BleepingComputer, a free community where people like yourself come together to discuss and learn how to use their computers. Using the site is easy and fun. As a guest, you can browse and view the various discussions in the forums, but can not create a new error 678 topic or reply to an existing one unless you are logged in. Other benefits of registering an account are subscribing to topics and forums, creating a blog, and having no ads shown anywhere on the site. Click here to Register a free account now! or read our Welcome Guide to learn how to use this site. Error 678 USB external 2.0 connection problem error modem Started by thompson7712 , Mar 28 2014 10:05 PM Please log in to reply 4 replies to this topic #1 thompson7712 thompson7712 Members 3 posts OFFLINE Local time:10:13 PM Posted 28 March 2014 - 10:05 PM I am hoping you can help me. I set up my mothers new computer and unfortunately she lives in the boonies and still has dial up. Since the new computer only has a network card I bought the external USB modem for it due to high ratings and reviews but unfortunately I am unable to get online with it. The modem dials, goes through the tones etc but does not make connection with the remote computer.. I know the modem is working because I can input my cell number as a test to dial and it dials the call just fine. I called the internet provider but I'm not accepting that because just an hour before we were online with the old computer with a built in 56k modem. The new comp has Windows 8.1 on it, the user name/ pass and dial up