Psecure Violation Error Detected Cisco
Contents |
SwitchingSpanning Tree ProtocolTroubleshoot and AlertsConfiguration Example and TechNotes Errdisable Port State Recovery on the show port security violations Cisco IOS Platforms Download Print Available Languages Download Options PDF
Errdisable Recovery Cause Psecure-violation
(143.8 KB) View with Adobe Reader on a variety of devices ePub (82.1 KB) View in cisco clear port security violation various apps on iPhone, iPad, Android, Sony Reader, or Windows Phone Mobi (Kindle) (87.6 KB) View on Kindle device or Kindle app on multiple devices %pm-4-err_disable: link-flap error detected Updated:Mar 23, 2016 Document ID:69980 ContentsIntroductionPrerequisitesRequirementsComponents UsedBackground InformationPlatforms That Use ErrdisableErrdisableFunction of ErrdisableCauses of ErrdisableDetermine If Ports Are in the Errdisabled StateDetermine the Reason for the Errdisabled State (Console Messages, Syslog, and the show errdisable recovery Command)Recover a Port from Errdisabled StateCorrect the Root ProblemReenable the Errdisabled PortsVerifyTroubleshootRelated Information Introduction This
Err-disabled Bpduguard
document defines the errdisabled state, describes how to recover from it, and provides examples of errdisable recovery. This document uses the terms errdisable and error disable interchangeably. Customers often contact Cisco Technical Support when they notice that one or more of their switch ports have become error disabled, which means that the ports have a status of errdisabled. These customers want to know why the error disablement happened and how they can restore the ports to normal. Note: The port status of err-disabled displays in the output of the show interfaces interface_number status command. Prerequisites Requirements There are no specific requirements for this document. Components Used In order to create the examples in this document, you need two Cisco Catalyst 4500/6500 Series Switches (or the equivalent) in a lab environment with cleared configurations. The switches should run Cisco IOS® Software and each switch should have two Fast Ethernet ports that are capab
Catalyst 3750 Series SwitchesConfigureConfiguration Examples and TechNotes Layer 2 Security Features on Cisco Catalyst Layer 3 Fixed p secure Configuration Switches Configuration Example Download Print Available Languages Download Options security violation error detected PDF (32.8 KB) View with Adobe Reader on a variety of devices Updated:Jan 17, 2007 Contents
Debug Port Security
Introduction Prerequisites Requirements Components Used Related Products Conventions Background Information Configure Network Diagram Port Security DHCP Snooping Dynamic ARP Inspection IP Source Guard Verify Troubleshoot Related Information http://www.cisco.com/c/en/us/support/docs/lan-switching/spanning-tree-protocol/69980-errdisable-recovery.html Introduction This document provides a sample configuration for some of the Layer 2 security features, such as port security, DHCP snooping, dynamic Address Resolution Protocol (ARP) inspection and IP source guard, that can be implemented on Cisco Catalyst Layer 3 fixed configuration switches. Prerequisites Requirements There are no specific requirements for this document. Components http://www.cisco.com/c/en/us/support/docs/switches/catalyst-3750-series-switches/72846-layer2-secftrs-catl3fixed.html Used The information in this document is based on the Cisco Catalyst 3750 Series Switch with version 12.2(25)SEC2. The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command. Related Products This configuration can also be used with these hardwares: Cisco Catalyst 3550 Series Switches Cisco Catalyst 3560 Series Switches Cisco Catalyst 3560-E Series Switches Cisco Catalyst 3750-E Series Switches Conventions Refer to Cisco Technical Tips Conventions for more information on document conventions. Background Information Similar to routers, both Layer 2 and Layer 3 switches have their own sets of network security requirements. Switches are susceptible to many of the same Layer 3 attacks as routers. However, switches and Layer 2 of the OSI reference model in general, are subject to network attacks in differ
Frame-Relay IP Routing RIP EIGRP OSPF BGP Multicast IPv6 Quality of Service Network Management Network Services Security MPLS Security Cisco ASA Firewall New Lessons Lesson Ideas Forum Lessons Discussion Cisco Networking Cisco Certifications General Discussion Support Log In Table of ContentsSwitchingUnit 1: Switching Basics How does a switch learn MAC Addresses Static MAC Address Table Entry CEF (Cisco Express Forwarding) Cisco SDM (Switching Database Manager) Troubleshooting Interfaces Unit 2: VLANs and Trunking Introduction to VLANs (Virtual LAN) How to configure VLANs 802.1Q Encapsulation How to configure a trunk between switches How to change the Native VLAN Cisco DTP (Dynamic Trunking Protocol) Negotiation 802.1Q Tunneling (Q-in-Q) Etherchannel over 802.1Q Tunneling Private VLANs (PVLAN) InterVLAN Routing Troubleshooting VLANs & Trunks Troubleshooting Inter-VLAN Routing Unit 3: VTP (VLAN Trunking Protocol) VTP (VLAN Trunking Protocol) VTP Version 3 Unit 4: Spanning-Tree Introduction to Spanning-Tree Spanning-Tree Cost Calculation PVST (Per VLAN Spanning Tree) Spanning-Tree Port States Spanning-Tree TCN (Topology Change Notification) Spanning-Tree Portfast Spanning-Tree UplinkFast Spanning-Tree Backbone Fast Rapid Spanning-Tree Rapid Spanning-Tree Configuration MST (Multiple Spanning-Tree) Spanning-Tree BPDUFilter Spanning-Tree BPDUGuard Spanning-Tree RootGuard Spanning-Tree LoopGuard and UDLD Troubleshooting Spanning-Tree FlexLinks Unit 5: Etherchannel Introduction to Etherchannel Layer 3 Etherchannel Troubleshooting Etherchannel Unit 6: Virtualization Cisco Switch Virtualization Cisco Stackwise Unit 7: Design Unicast Flooding due to Asymmetric Routing Unit 8: Security How to configure port-security on Cisco Switch Protected Port DHCP Snooping ARP Poisoning DAI (Dynamic ARP Inspection) Unit 9: Miscellaneous Cisco IOS SPAN and RSPAN Cisco Small Business Switch VLAN Configuration RMON Statistics Collection on Cisco Catalyst Switch You are here: Home » Switching How to configure port-security on Cisco Switch Posted on February 15, 2013 by Rene Molenaar in CCIE Routing & Switching, CCIE Routing & Switching Written, CCNA Routing & Switching, CCNP SWITCH, Switching 26 votes By default there is no limit to the number of MAC addresses a switch can learn on an interface and all MAC addresses are allowed. If we want we can change this behavior with port-security. Let’s take a look at the following situation: In the topology above someone connected a