Error 0c0032 00000003
Contents |
TWI Documents Library Index Page HP Designjet 1000 Series Printers - TWI: System Error 0C0032 In this document: Parts required (part numbers are subject to change) Inspect and Clean the Drop Detect Sensor
Hp Designjet 5500 Error Codes
Service Station Calibration Calibrations backup Pen alignment Multi-Roll feeder disassembly Removing the Multi-Roll feeder hp designjet 1050c error codes left side cover Removing the Multi-Roll feeder right side cover Installation of covers Document number: BPP90149 Last Updated: 10-Jan-2003 Minimum skill hp designjet 5500 printhead reseat error level: 2This error indicates that Drop Detector is not calibrated for all printheads. Possible causes are the Drop Detector or Service Station being previously replaced and the necessary calibrations not being performed. Other causes can include
Hp Designjet 5500 Printhead Error Codes
a faulty Drop Detector or in rare circumstances the Electronics module. Follow the steps listed below to determine the actual cause of the failure and to replace the appropriate parts. NOTE: If the printer is installed on a Multi-Roll feeder accessory, some Multi-Roll disassembly is required to gain access to the printer. Instructions for Multi-Roll disassembly are listed at the bottom of this document for reference.Parts required (part numbers are subject
Hp Designjet 5500 Service Manual
to change) Part Description Models - C6074A, C6075A Models - C6074B, C6075B Drop Detector (Required) C6072-60400 C6072-60400 Electronics Module (Required) C6072-69146 C6074-60283 Electronics Module Fuse (Required) C6074-60467 C6074-60467 Trailing Cable (Optional) see note below C6074-60418 C6074-60418 Maintenance Kit (Optional) C6072-60395 C6072-60395 NOTE: If the printer is an "A" model,(i.e. - not a plus model) a Trailing cable must be sent with the rest of the parts listed. NOTE: The fuse being sent should be used if a poor Trailing cable connection or a shorted Trailing cable blows the fuse on the Electronics module. Make sure to properly connect the Trailing cable or replace a shorted Trailing cable before installing the new fuse. NOTE: If the system error code 0C0032 appeared after recent removal and replacement of an Electronics module (for `A' models) or Main PCA (for `B' models), then most likely, the calibrations backup has not been performed. If this is the case, proceed to Calibrations Backup and Pen Alignment sections listed below. If the system error persists, the service station calibration must be performed.Inspect and Clean the Drop Detect SensorIf any of the troubleshooting steps listed below solve the problem, attempt to verify printer functionality by printing several internal prints. If functionality is verified, no additional parts should be rep
He appears " error of sistema" in display of ploter. 0c0032 00000004.Anticipated thanks to the commentaries. Respond to this 0 I have no idea what you hp designjet 5500 error 1f50007 are talking about but the error indicates the drop detector isnt working
Hp 5500 Printhead Problems
properly which is a very common problem with this machine. Its on the left side of the service station and hp designjet 5000 service manual theres just a blue screw holding it inplace. You need to remove the right side cover and unplug it from the back and it comes right out. Just clean it up http://www.computercarefiles.com/TWI_Docs/bpp90149/default.html really good and remove the excess ink from it. Reinstall and run the service station calibration and you should be done. Ive only had to replace two, all the others Ive been able to clean out. by nivek on Jan 15, 2009 at 5:14pm Add comment Please sign in to comment 0 Ok, I am going to watch what you say to me. Thanks http://www.fixyourownprinter.com/posts/60146 for its indication. I will inform to him. And perhaps so that it is not understood well to me, it is that I am Spanish and I translate what I write here. Pardon by my English. by eriq on Jan 15, 2009 at 11:34pm Add comment Please sign in to comment 0 Hello. I have been going to see ploter, I comment to you. - When realising the calibration of injectors, appears the error in display 0c0032 00000004. The impression for the calibration of injectors, the black color prints defectively, almost does not print. - As I can see in the menu of ploter the section of the calibration of " SERVICE STATION" , because in the menu it is not that section.- The piece " DROP DETECTOR" , I realise a cleaning to him or the change. Thanks and a greeting. by eriq on Jan 16, 2009 at 7:41am Add comment Please sign in to comment 0 All the printheads need to be functioning to do the calibration if the black or any of the colors is failing you need to replace. Go into utilities menu under printer set
I.D./Label Equipment Lamination Equipment Monitors Paper Handling Equipment Phone Equipment/Equipment/Answering Plotters Scanners SoftwareTypewriters Supplies Toner & Toner Cartridges Inkjet Ink & Cartridges Ribbons/Rolls Consumables Multifunction Parts Large/Wide Format Parts Printer Parts Other http://www.theprinternetwork.com/showthread.php?5457-Designjet-1055cm-0C0032-Error Parts The Printer Network:Now Mobile-Ready! Register Help Remember Me? News Forum New Posts FAQ Calendar Forum Actions Mark Forums Read Quick Links Today's Posts Unanswered Posts View Site Leaders New Content Blogs Press Releases OMBE Stores Products for Sale Advanced Search Forum Ink Jet Printer Technical Discussions HP Designjet 1055cm 0C0032 Error If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before hp designjet you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. Results 1 to 2 of 2 Thread: Designjet 1055cm 0C0032 Error Thread Tools Show Printable Version Search Thread Advanced Search Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode 10-25-2011,07:27 PM #1 mrfuser View Profile View Forum Posts View Blog Entries View Articles Member Join Date Dec 2005 hp designjet 5500 Posts 38 Machine says ready, but prints blanks and then goes into the error 0C0032-00000004. Everything looks fine. Any ideas? First time working on this model for a client. Thanks Kelly Reply Reply With Quote 11-09-2011,08:11 PM #2 machinercylr View Profile View Forum Posts View Blog Entries View Articles Junior Member Join Date Sep 2006 Location Hayward,Ca Posts 5 Hi, we had the same pop up and this broke down to a communication error. These have a jet direct card for network. What we did was turn off power by unplugging the cord from the back of the plotter. then while the memory is clearing it's of the error code (30 seconds minimum) removing the JD card and plug it back in and out several time to insure the connections are making good contact. Then plugging it back and powering up. Also make sure that your firmware is up to date. Best Regards, MachineRcylr Best Regards, MachineRcylr Reply Reply With Quote Quick Navigation HP Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums Tips Tips Industry Issues Industry Issues Manufacturer Discussions Managed Print Services Managed Print Services Connectivity / Networking / Drivers Connectivity / Networking Drivers Dot Matrix / Impact Printer Technical Discussions Dot Matrix / Impact Ink Jet Printer Technical Discussions Brother Canon Epson HP Xerox Other - Ink Jets Large