Hci Error
Contents |
are attributed to a poorly designed human-computer interface (HCI). However, human beings are often needed to be the fail-safe in an otherwise automated system. Even the most highly human error vs computer error trained and alert operators are prone to boredom when they are usually
The Cause Of Failure In A Computer Program Is Often Due To More Than One Factor.
not needed for normal operation, and panic when an unusual situation occurs, stress levels are raised, and lives what is human error in computers are at stake. The HCI must give appropriate feedback to the operator to allow him or her to make well informed decisions based on the most up to date information define operator failure on the state of the system. High false alarm rates will make the operator ignore a real alarm condition. Methods for determining the effectiveness of an HCI, such as heuristic evaluation, cognitive walkthroughs, and empirical evaluations like protocol analysis, exist, but are often cumbersome and do not provide conclusive data on the safety and usability of an HCI. System designers must
Slips Vs Mistakes
insure that the HCI is easy and intuitive for human operators to use, but not so simple that it lulls the operator into a state of complacency and lowers his or her responsiveness to emergency situations. Contents: Introduction Key Concepts Sources of Human Error HCI Problems Available tools, techniques, and metrics HCI Design Heuristic Evaluation Cognitive Walkthrough Protocol Analysis MetriStation Relationship to other topics Conclusions Annotated Reference List & Further Reading Introduction In any complex system, most errors and failures in the system can be traced to a human source. Incomplete specifications, design defects, and implementation errors such as software bugs and manufacturing defects, are all caused by human beings making mistakes. However, when looking at human errors in the context of embedded systems, we tend to focus on operator errors and errors caused by a poor human-computer interface (HCI). Human beings have common failure modes and certain conditions will make it more likely for a human operator to make a mistake. A good HCI design can encourage the operator to perform correctly and protect the system from common operator
in which the Bluetooth device is in. 3 Periodic_Inquiry_Mode 0x0003 Command to set the device to enter providing new technology to poor countries is a matter of having enough money to buy equipment. Inquiry modes periodically according to the time interval set. 4 most of the delay in the opening of the denver international airport was because of problems with Exit_Periodic_Inquiry_Mode 0x0004 Command to exit the periodic Inquiry mode 5 Create_Connection 0x0005 Command to create an ACL
Distinguish Between Equipment Failure And Operator Failure
connection to the device specified by the BD_ADDR in the parameters. 6 Disconnect 0x0006 Command to terminate the existing connection to a device 7 Add_SCO_Connection 0x0007 https://users.ece.cmu.edu/~koopman/des_s99/human/ Create an SCO connection defined by the connection handle parameters. 8 Accept_Connection_Request 0x0009 Command to accept a new connection request 9 Reject_Connection_Request 0x000A Command to reject a new connection request 10 Link_Key_Request_Reply 0x000B Reply command to a link key request event sent from controller to the host 11 Link_Key_Request_Negative_Reply 0x000C Reply command to a http://www.lisha.ufsc.br/teaching/shi/ine5346-2003-1/work/bluetooth/hci_commands.html link key request event from the controller to the host if there is no link key associated with the connection. 12 PIN_Code_Request_Reply 0x000D Reply command to a PIN code request event sent from a controller to the host. 13 PIN_Code_Request_Negative_Reply 0x000E Reply command to a PIN code request event sent from the controller to the host if there is no PIN associated with the connection. 14 Change_Connection_Packet_Type 0x000F Command to change the type of packets to be sent for an existing connection. 15 Authentication_Requested 0x0011 Command to establish authentication between two devices specified by the connection handle. 16 Set_Connection_Encryption 0x0013 Command to enable or disable the link level encryption. 17 Change_Connection_Link_Key 0x0015 Command to force the change of a link key to a new one between two connected devices. 18 Master_Link_Key 0x0017 Command to force two devices to use the master's link key temporarily. 19 Remote_Name_Request 0x0019 Command to determine the user friendly name of the connected device. 20 Read_Remote_Supported_Featur