Protection Error 89
Username and Password to log in. If you have not yet registered, you can register here. Username: Password: Have you forgotten your login information? Board Rules · Mark all read Default Styleubbthreads_dark_blueubbthreads_dark_purpleubbthreads_divinity2ubbthreads_larianubbthreads_larian_darkubbthreads_light_blueubbthreads_old_larian_boards Contact Us · Larian Studios · Top Powered by UBB.threads™ PHP Forum Software 7.5.8
Conditioner KF-70DW/NA1 Technical & service manual Gree KF-70DW/NA1 Technical & Service Manual: Low Voltage Protection; Error Codes; Timer Off; Other Control Hide thumbs 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 If the above phenomenons existed, the unit cannot resume to run, E4 will be http://larian.com/forums/ubbthreads.php?ubb=showflat&Number=300540 display. Press ON/OFF button to turn off the unit, repress ON/OFF button return to run at the original running mode. 7.3.5 Indoor ultra high temperature protection In HEAT mode, when detected the evaporator tube temp. is too high, outdoor fan motor stop running; when evaporator tube temp. get right, outdoor fan motor start up. 7.3.6 Low voltage protection Compressor is turned on, http://www.manualslib.com/manual/1024526/Gree-Kf-70dw-Na1.html?page=16 if the current had been detected exceed 22A, the room ambient temp. achieved the setting temp., the unit will stop. When compressor had stopped 3min, it will automatically return to the original setting mode. When displaying E5, can not automatically return to the original running mode, that need to press ON/OFF button to turn off the unit, then repress the ON/OFF button to resume to work. 7.3.7 Error codes E1: Compressor high pressure protection E2: Indoor anti-freezing protection E3: Compressor low pressure protection E4: Air exhaust pipe high temp. protection E5: Low pressure protection 7.4 Functions of Sleep and Timer: 7.4.1 Sleep If controller is in COOL mode or DRY mode, after SLEEP operation run for 1hour, the presetting Tset will be increased 1 ℃, 2hours later, it will be increased 1 ℃ , i t ha s been decreased 2 ℃ wi thin 2hours in all, then it runs at the setting temp. If controller is in HEAT mode, after SLEEP operation run for 1hour, the presetting Tset will be decreased 1℃ 2 hours later it will be decreased 1℃, it has been decreased
then the RESPMSG parameter returns the description of the RESULT code. A value of 0 (zero) indicates that https://www.paypalobjects.com/en_US/vhelp/paypalmanager_help/result_values_for_transaction_declines_or_errors.htm no errors occurred and the transaction was approved. A value greater than zero indicates a decline or an error. RESULT RESPMSG and Explanation 0 Approved For Account Verification authorization transactions, RESULT=0 with RESPMSG=Verified. 1 User authentication failed. Error is caused by one or more of the following: Invalid Processor information entered. Contact merchant bank protection error to verify. "Allowed IP Address" security feature implemented. The transaction is coming from an unknown IP address. For more information, refer to Allowed IP Addresses. You are using a test (not active) account to submit a transaction to the live PayPal servers. Change the URL from pilot-payflowpro.paypal.com to payflowpro.paypal.com. 2 Invalid tender type. Your protection error 89 merchant bank account does not support the following credit card type that was submitted. 3 Invalid transaction type. Transaction type is not appropriate for this transaction. For example, you cannot credit an authorization-only transaction. 4 Invalid amount format. Use the format: “#####.##” Do not include currency symbols or commas. For processors that do not support Account Verification, you will receive this RESULT code if you process a $0 transaction. 5 Invalid merchant information. Processor does not recognize your merchant account information. Contact your bank account acquirer to resolve this problem. 6 Invalid or unsupported currency code 7 Field format error. Invalid information entered. See RESPMSG. 8 Not a transaction server 9 Too many parameters or invalid stream 10 Too many line items 11 Client time-out waiting for response 12 Declined. Check the credit card number, expiration date, and transaction information to make sure they were entered correctly. If this does not resolve the problem, have the customer call their card issuin