718 Error Dial Up
Contents |
POSSIBLE CAUSES: Poor phone line quality A problem dial up error 678 with the server at the ISP The wrong username and or password was entered. The dial up error 721 wrong phone number was dialled by the connection.. The server type settings maybe incorrect on the computer. The modem may need initialisation string to stabilise its operation. POSSIBLE RESOLUTIONS: If you
Error 718 The Connection Was Terminated
are using extension cords or faxes or any other similar device, disconnect them and try again Find out if Actrix is experiencing any server problems (0800-228749). Make sure the correct username and or password have been entered. Verify that the correct access number is being used, ie. 086722874. Make sure the server types in dial up networking is set to PPP, and TCP/IP box is ticked. Use a initialisation string such as +ms=v90 for smoother operation. Does this all sound a little complicated? Call the Actrix helpdesk for assistance (0800-228749).
Ethernet & T1 Service trueSTREAM Business Standard DSL Hosted Voice Service Website Hosting SUPPORT error 691 dial up SUPPORT Where are you? Support > Knowledge Base > DSL Support error 732 dial up > Dynamic IP > Windows XP PPPoE Client Error 718 Windows XP PPPoE Client Error 718 Print Windows XP PPPoE
Error 718 Vpn
Client Error 718Error 718 indicates a PPP timeout. This means that your computer began communicating with the ISP side server but disconnected before a response was given. This can be caused by a number http://editor.actrix.co.nz/byarticle/dune718.htm of things such as poor line quality, active LCP extensions, or ISP side server issues. To trouble shoot error 718 please follow the steps listed below.1. Next you will want to try isolating the line to improve line quality. To do this remove all phone devices from the line the DSL modem is on, and make sure there is no ADSL micro filter placed on the DSL Modem. https://www.dslextreme.com/support/kb/dsl-support/dynamic-ip/windows-xp-pppoe-client-error-718 After you have made sure that the DSL modem is the only phone device on that line attempt to connect again.2. Next reboot your computer and power cycle your modem. Power cycling is the act of turning the modem off for 10-15 seconds and then turning it back on. When the sync light on your DSL modem (normally labeled ready/sync/dsl/line) goes solid attempt to connect again.3. If you are still unable to connect try disabling any active LCP extensions. To do this first head into network connections. Right click on the broadband connection labeled dslextreme and select properties. Click on the networking tab, highlight internet protocol (TCP/IP) and then click on settings. Uncheck the box labeled LCP extensions and then select ok. Then select ok on the connection properties. Now attempt to connect again.If this error still persists call DSL technical support at 866-491-7221 to speak with a tech support representative about your issue. Created On: 10/25/2004 7:54:00 AM Last Modified On: 10/26/2010 2:41:00 PM Article ID: 10103 Viewed 12,721 times Search our Knowledge Base Do the links above not match what problem you're trying to solve or question you might have? With over 600 articles and growing our
Quick Init Reference • Error Message Fixes • Line Noise Tests • Virus Removal Guide http://www.modemhelp.net/dunerror/error_718.shtml • Articles • F.A.Q.'s • Basic AT Commands • Access Server Codes • Tech Humor • Links • FREE Error Scan • News Archive • http://windowsitpro.com/networking/solving-ras-718-error Search • Feedback • Survey • Legal • About Outdated DriversCan cause hardware related Errors. Check your PC Drivers now. Error 718 1. Reboot the dial up machine, verify your Username and Password, and try again. Check for realms, if in NT make sure you have nothing under domain, accept any auth including clear text is checked, and try unchecking Enable PPP LCP extensions. Make sure logon to network isn't checked. Make sure that nothing is typed in dial up error the DOMAIN field if this is NT. 2. This is often a POP problem. Try logging onto a different POP. 718 is usually on the ISP's end, but NOT ALWAYS. If there are multiple calls coming into the ISP's callcenter then they could see a problem, but if not, it is probably the user's computer. 3. Nuke the pwl files. 4. Have ISP reset the password. 5. Recreate connectoid. 6. Full uninstall and reinstall of connectoid, network, and DUN/RAS. 7. This can sometimes also be a communications problem caused by heavy line noise or modem problems. Try updating the modem drivers, inits, commas, etc...and have a line noise test performed. More info on error 718 can be found at: http://www.deja.com/[ST_rn=qs]/qs.xp?QRY=microsoft+718&OP=dnquery.xp&ST=QS&DBS=2 This page was last modified on Saturday, 05-Feb-2011 15:11:54 EST. This website is ©1999-Present Bradford Liedel DBA ModemHelp Networks and Web Services. Mason, MI 48854 USA. All rights reserved.
WindowsWindows 10 Windows Server 2012 Windows Server 2008 Windows Server 2003 Windows 8 Windows 7 Windows Vista Windows XP Exchange ServerExchange Server 2013 Exchange Server 2010 Exchange Server 2007 Exchange Server 2003 Outlook Unified Communications/Lync SharePoint Virtualization Cloud Systems ManagementSystem Center PowerShell & Scripting Active Directory & Group Policy Mobile Networking Storage TrainingOnline Training IT/Dev Connections Webcasts VIP Library Digital Magazine Archives InfoCentersIT Innovators Mobile Computing Business Now Desktop VDI All About Converged Architecture Advertisement Home > Systems Management > Networking > Solving a RAS 718 Error Solving a RAS 718 Error Sep 16, 2001 Sean Daily | Windows IT Pro EMAIL Tweet Comments 0 Advertisement I have a BDC in a remote office. I usually use a DSL-based VPN connection through my ISP to connect the BDC to my corporate network. When my DSL connection goes down, I want to use a dial-up connection to link my BDC through a PPTP-based VPN to my company's Windows NT 4.0 server (which functions as a RAS server and a BDC). However, I can't make this connection work. I can dial in to the RAS server through a direct-dial connection, but when I try to connect to the PPTP server, I get a RAS 718 error. Can you help me? First, make sure that all the servers are running NT 4.0 Service Pack 6a (SP6a), which fixed known problems that relate to the symptoms you describe. If the machines all run the most recent service pack, the problem might be a timeout on the PPTP session. Such a timeout can be a result of latency on the connection (for more information, see the Microsoft article "Troubleshooting PPTP Connectivity Issues in Windows NT 4.0" at http://support.microsoft.com/support/kb/articles/q162/8/47.asp). The solution is to increase the number of attempts that PPTP makes to transmit data over the connection. Locate the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters registry subkey. If the PPTP-TcpMaxDataRetransmissions value (of type REG_DWORD) doesn't exist under this subkey, add the value, which has a range of 0 to 0xFFFFFFFF and a default of 9h. The PPTPTcpMaxDataRetransmissions value controls the maximum number of times that the local system retransmits a PPTP packet when the remote host on the PPTP session doesn't acknowledge the packet. By design, this value's default is set higher than the default of