Dial Up Connection Error 718
Contents |
POSSIBLE CAUSES: Poor phone line quality A problem dialup error 718 with the server at the ISP The wrong username and or password was entered. The dsl error 718 wrong phone number was dialled by the connection.. The server type settings maybe incorrect on the computer. The modem may need initialisation string to stabilise its operation. POSSIBLE RESOLUTIONS: If you
Error 732 Dial Up
are using extension cords or faxes or any other similar device, disconnect them and try again Find out if Actrix is experiencing any server problems (0800-228749). Make sure the correct username and or password have been entered. Verify that the correct access number is being used, ie. 086722874. Make sure the server types in dial up networking is set to PPP, and TCP/IP box is ticked. Use a initialisation string such as +ms=v90 for smoother operation. Does this all sound a little complicated? Call the Actrix helpdesk for assistance (0800-228749).
not establish a connection to the Internet. The PPP prefix of the error is defined as "Point-to-Point Protocol" and it is a protocol (set of instructions) that are used between two computers over a serial interface, such as dial up.
Error 691 Dial Up
PPP is used in dial up to connect the computer to a server via means error 619 dial up of a serial modem. The error can occur for a variety of reasons, such as faulty drivers or a simple mistype of the error 721 dial up user name. What Causes PPP Error 718? The error message associated with this error is: Error 718: the computer you're dialing in to cannot establish a Dial-Up Networking connection. Check your password, and then try again. or Error http://editor.actrix.co.nz/byarticle/dune718.htm connecting to Connection Name: Verifying user name and password Error 718: Timed out waiting for a valid response from the remote PPP Peer These error messages are saying that the your computer is not receiving a response from a PPP server. Typically, this could be the result of: faulty drivers installed for your modem; incorrect login details or a faulty internet connection. With this error, you will not be able to access any internet related activites, http://www.personalcomputerfixes.com/general-errors/how-to-fix-ppp-error-718/ such as email or the world wide web. How To Fix PPP Error 718 Step 1 - Check Your Internet Connection Checking your internet connection should always be the first port of call with any internet related error. It distinguishs whether you have a problem with your system, or it is an error that has no substance. To check your internet connection: Click Start > Browsername (Where browser name is the name of your default browser) Type http://www.google.co.uk Google is always online so testing to see if it will load will be a good indicator for your internet connection. If it loads, you need not worry about the error. If it doesn't load, you will not be connected to the internet. You should check the phone line and other hardware, to see if they are configured correctly and plugged in. A simple cable that is unplugged or not plugged in correctly could lead to this error. If, after you have done this, the error is still present and you cannot connect to the internet, it may be the problem of your modem drivers. Step 2 - Upgrade Modem Driver An out of date modem driver or a corrupt modem driver will stop the device from functioning properly, causing the PPP 178 erro. You should visit the manufacturer of your modem to ensure you have the correct and
Centre Mobile & Data Internet & Email Landline Billing Tech In A Sec Home Help Internet & Data Internet Troubleshooting Error 718 - Connection timed out Personal Business HomeOpen https://www.spark.co.nz/help/internet-data/troubleshooting/error-718-connection-timed-out/ Shop Get more Help Contact HomeOpen Shop Work Smarter MySpark Help Contact Back http://windowsitpro.com/networking/solving-ras-718-error Error 718 - Connection timed out This problem is most likely caused by an incorrectly configured dialler, poor line quality or a problem with the server at the ISP, when trying to connect to the Internetin Windows. Error Message Error 718 - The connection timed out waiting for a valid response from the remote dial up computer To resolve Before you start, make a note of whether the connection was working before, if any changes were made by the user, and, the type of modem that was installed. Verify the user's account is active and authenticates Trash the customer from the Authentication Cache Delete their existing diallerand recreate it Restart the computer and modem if it's an external modem Slow the modem to dial up connection v34 Restart the computer and retry Try the alternative Spark dial-up numbers. If it is currently set to 087303030, try 087303031 or 087303032. If the same error occurs then revert to 087303030 and continue Contact Spark Faults (120) and request a NTS test on the line. If the NTS test reports a fault on the line, warm conference your customer to Spark Faults for a line fault repair technician booking. How helpful is this page? © Copyright Spark 2016 All rights reserved Help us improve this page How could we make this page better? 1000 characters Cancel send message Cancel send message Help improve this page Print this page Email this page Back to top Home Help Internet & Data Internet Troubleshooting Error 718 - Connection timed out Shop Mobile Internet Landline Get More Lightbox Spotify Free WiFi Security Free email Spark Thanks Help Tech in a Sec Internet Mobile Landline Billing MySpark Sign in Register My Mobile My Mobile Broadband My Internet My Landline Contact Store Finder Follow us Spark New Zealand | Spark Digital | Spark Ventures | Spark Foundation © Copyright Spark 2016 All rights reserved Legal disclaimer | Privacy Policy | Accessibility | Terms and Conditions
WindowsWindows 10 Windows Server 2012 Windows Server 2008 Windows Server 2003 Windows 8 Windows 7 Windows Vista Windows XP Exchange ServerExchange Server 2013 Exchange Server 2010 Exchange Server 2007 Exchange Server 2003 Outlook Unified Communications/Lync SharePoint Virtualization Cloud Systems ManagementSystem Center PowerShell & Scripting Active Directory & Group Policy Mobile Networking Storage TrainingOnline Training IT/Dev Connections Webcasts VIP Library Digital Magazine Archives InfoCentersIT Innovators Mobile Computing Business Now Desktop VDI All About Converged Architecture Advertisement Home > Systems Management > Networking > Solving a RAS 718 Error Solving a RAS 718 Error Sep 16, 2001 Sean Daily | Windows IT Pro EMAIL Tweet Comments 0 Advertisement I have a BDC in a remote office. I usually use a DSL-based VPN connection through my ISP to connect the BDC to my corporate network. When my DSL connection goes down, I want to use a dial-up connection to link my BDC through a PPTP-based VPN to my company's Windows NT 4.0 server (which functions as a RAS server and a BDC). However, I can't make this connection work. I can dial in to the RAS server through a direct-dial connection, but when I try to connect to the PPTP server, I get a RAS 718 error. Can you help me? First, make sure that all the servers are running NT 4.0 Service Pack 6a (SP6a), which fixed known problems that relate to the symptoms you describe. If the machines all run the most recent service pack, the problem might be a timeout on the PPTP session. Such a timeout can be a result of latency on the connection (for more information, see the Microsoft article "Troubleshooting PPTP Connectivity Issues in Windows NT 4.0" at http://support.microsoft.com/support/kb/articles/q162/8/47.asp). The solution is to increase the number of attempts that PPTP makes to transmit data over the connection. Locate the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters registry subkey. If the PPTP-TcpMaxDataRetransmissions value (of type REG_DWORD) doesn't exist under this subkey, add the value, which has a range of 0 to 0xFFFFFFFF and a default of 9h. The PP