Error In User Data Dvbviewer
Several functions may not work. Please re-enable javascript to access full functionality. DVBViewer 5.6.4 released / DVBViewer 5.6.4 veröffentlicht | Recording Service 1.33.1 released / Recording Service 1.33.1 veröffentlicht Error in Userdata! Started by `Henry` , Jan 22 2009 13:40 Please log in to reply 19 replies to this topic #1 `Henry` `Henry` Newbie Members 15 posts Posted 22 January 2009 - 13:40 I have just brought DVBViewer, it is great. However after watching a moment later a box popup said Error in Userdata! If I start recording it will pop up after a minute then DVBViewer quit itself ! I have also tried DVBViewer under Administrator and normal user, but same problem ! What the heck !? Attached Files dvbviewer.jpg 16.51KB 93 downloads Back to top #2 Lars_MQ Lars_MQ Board Inventar Board Inventar 26,375 posts Posted 22 January 2009 - 13:49 the entered userdata are not correct. try installing the DVBViewer again, this time make sure you enter the userdata correctly. Back to top #3 `Henry` `Henry` Newbie Members 15 posts Posted 22 January 2009 - 13:54 the entered userdata are not correct. try installing the DVBViewer again, this time make sure you enter the userdata correctly.I am new user, this is clean install.And I have also tried uninstall DVBViewer then install again.What's wrong with that ? Back to top #4 `Henry` `Henry` Newbie Members 15 posts Posted 23 January 2009 - 04:03 It is working now, tested over night. But my firewall keep report the program is sending and receiving data, what is that ? Back to top #5 npmak npmak Newbie Members 1 posts Posted 24 January 2009 - 17:12 It is working now, tested over night.But my firewall keep report the program is sending and receiving data, what is that ?I just install the DVBViewer and I have the "Error in Userdata" too. What have you "change" in "userdata" during installation to get rid of the error?Many thanks. Back to top #6 TeaTray TeaTray Newbie Members 7 posts Posted 07 February 2009 - 17:46 I just install the DVBViewer and I have the "Error in Userdata" too. What have you "change" in "userdata" during installation to get rid of the error?Many thanks....and I have had this error ever since the upgrade to version 4.0.0 Everything was fine, until then. At first, it was giving an error every 23 minutes or so (but a bit random), whether logged in as Administrator or user. Then, I logged in as Administrator and uninstalled/re-installed. I lost all my customization, but not the channels
DVBViewer Files Restricted User Accounts 3. Fundamental Operating Steps Display Controls Channel List Other Settings Recording The Teletext Window The EPG Window Plugins & Info 4. Display Adjustments Display Settings The DVBViewer OSD Zoom Adjustments Filter Settings 5. Recording and Playback Basic Information Media Playback Playback Using the Playlist Splitting of Video Files File Format Recording Timer Programming TimeShift 6. The Channel List Navigation Channel Editing Channel Sorting Channel Search Import and Export External Favourite Lists 7. The Options Window General Options Extended Options TV & Radio Options Recorder Options Network Streaming Input 8. Troubleshooting In the http://www.dvbviewer.tv/forum/topic/31944-error-in-userdata/ Correct Order Points for Diagnosis Known Problems 9. Tools and Links Informative Pages Conversion and Editing Filters and Other Tools 10. Small Filter Guide DirectShow Filters AC3 / Dolby digital Experiments System Interventions 11. Plugins Graphselector Plugin Audiorecorder Plugin TVgenial Plugin Videorecorder Plugin 12. Legal Notes Trademarks Submissions Disclaimer 1. Introduction to the DVBViewer Pro® This chapter presents the program with its most important features, http://www.dvbviewer.com/en/?page=manual&chapter=h&sub=h3 describes the software and hardware requirements and informs how to purchase the full version. Before beginning to use this manual, you should have a working knowledge of your computer and its operating system. Make sure that you know how to use the mouse and standard menus and commands, and also how to open, save, and close files. If you need to review these techniques, see the printed or online documentation included with your Windows® OS. About this Guide This guide describes the handling of the DVBViewer Pro. The DVBViewer Pro offers numerous additional and extended functions with enhanced ease of use compared to the bundled DVBViewer TE (TechniSat Edition). It can be ordered for Euro 20 at http://www.dvbviewer.com/. With the purchase of the DVBViewer Pro you are entitled to all coming updates. The DVBViewer is subject to ongoing change due to progress in research and development. Therefore this guide may lack in actuality, although it is updated in regular intervals. An updated edition can be downloaded freely at http://www.dvbviewer.com/. Besides the description of the functions and options this guide is designed to serve the following purposes: As documentation for potential customers, considering to purchase the SkyS
and antenna rotors. In most cases DiSEqC is used for switching between satellite positions. There are different DiSEqC levels. TransEdit supports DiSEqC up to level 1.2 (which means, up to 64 satellite sources http://www.dvbviewer.com/griga/TransEdit%20E/DiSEqC.html and motorized dishes), provided the DVB-S card and driver allow to send such DiSEqC commands. General Remarks | DiSEqC Selection | DiSEqC Editor | Positioner Console General Remarks Sometimes DiSEqC does not work as expected. There are several reasons for it: Microsoft has missed to define a clear unified method for sending DiSEqC commands via the BDA interfaces (Broadcast Driver Architecture). Therefore every vendor of error in DVB-S devices uses a different method, or with other words, DiSEqC has to be implemented vendor-specific in an application. Some vendors only provide very poor documentation about their „private“ DiSEqC interface, some not at all. Often enough user feedback, trial and error are the only means to solve resulting problems. DVBViewer and TransEdit can only support DiSEqC for a specific DVB-S device if the interface is error in user sufficiently known. The interface of some vendors is limited to the basic DiSEqC 1.0 Pos/Opt commands. In this case DVBViewer and TransEdit cannot support cascaded switches (DiSEqC 1.1) or a positioner (DiSEqC 1.2). There are devices (particularly TechniSat SkyStar2) that provide a DiSEqC 1.1/1.2 interface, but the driver blocks according commands in order to avoid damage caused by the high power consumption of motorized dishes. DVB-S cards must generate the voltage for supplying switches, LNBs and positioners from the voltages that are available in a PC, thus being not so powerful as receivers with a dedicated power supply. Additionally it is more difficult in a PC to achieve an accurate DiSEqC timing. That is why sometimes a receiver is able to perform switching without problems, but not a DVB-S card connected to the same antenna cable – it may depend on the type of DVB-S device, its driver and the tolerance of the switch. The situation is complicated even more by companies selling relabeled hardware of other companies, sometimes with modified drivers. If you are not sure which DiSEqC Level is supported by your DVB-S device or which device is suitable for your needs,