Protocol Driver Error Access Gateway Enterprise
| 69 found this helpful | Created:26 Mar 2014 | Modified:10 Oct 2016 Languages log in to start download LOGIN Don't have an account? Create one here. Or Continue As Guest Which best describes you: IT Admin Business User DOWNLOAD Symptoms or
Unable To Launch Your Application Cannot Connect To The Citrix Xenapp Server Protocol Driver Error
Error Few users will be able to launch applications successfully however one of the following socket operation on non-socket error errors occur for other users when launching the published applications:"Unable to launch your application. Contact your help desk with the following socket operation on non-socket citrix information: Cannot connect to the Citrix XenApp server. Socket operation on non-socket" Cannot connect to the Citrix XenApp server. SSL Error 4: The proxy denied access to XXXX port XXXX. Also 1030 error is
Unable To Launch Your Application Cannot Open The Citrix Receiver
reported when launching VDA. Solution Important! This article is intended for use by System Administrators. If you are experiencing this issue and you are not a System Administrator, contact your organization’s Help Desk for assistance and refer them to this article. User License Exhausted Verify if the license is exhausted on NetScaler Gateway. Navigate to NetScaler configuration utility > NetScaler Gateway > Virtual Server and examine the Maximum Users and Current
Cannot Connect To The Citrix Xenapp Server There Is No Citrix Xenapp Server On The Specified Address
Users. If you notice both values are the same then the NetScaler Gateway license is exhausted. Or navigate to NetScaler configuration utility > System > Licenses to confirm the number of NetScaler Gateway and ICA licenses. Complete one of the following steps to resolve this issue: Install an additional Universal License to accommodate more users. Adjust the maximum number of users to match the new number of total users by navigating to NetScaler Gateway > Global Settings > Change Authentication AAA settings > Maximum Number of Users. Note: Retain NetScaler Gateway virtual server in SmartAccess mode. NetScaler Gateway setting should match with the type of license that NetScaler Gateway has. Change the NetScaler Gateway virtual server mode from SmartAccess to Basic. If Basic mode is used under NetScaler Gateway virtual server (ICA Only checkbox checked in latest versions of NetScaler) then unlimited ICA users are allowed. Refer to CTX125567 - How to Configure NetScaler Gateway Appliance with Unlimited ICA Connections for more information. Secure Ticket Authority Not Specified Verify if NetScaler Gateway has Secure Ticket Authority (STA) specified under NetScaler Gateway > Virtual Server > Published Application. If not, add the STA under Published Applications on NetScaler Gateway to resolve this issue. For more information refer to Cit
to launch your application. Contact your help desk with the following information: Cannot connect to the Citrix XenApp server. Protocol Driver error" Problem You attempt to launch a XenDesktop 5.5 or citrix receiver unable to launch your application ssl error 61 5.6 desktop through an NetScaler VPX Access Gateway but receive the following error
Citrix Receiver Unable To Launch Your Application Ssl Error 4
message from the Citrix Receiver: Unable to launch your application. Contact your help desk with the following information: Cannot connect to cannot connect to the citrix xenapp server the socket is not already bound to an address the Citrix XenApp server.Protocol Driver error Solution While this error message can be caused by various reasons, the first to check should be the following KB: Case Study: The Protocol Driver Error is displayed http://support.citrix.com/article/CTX134940 when starting an Application through Access Gateway Enterprise Edition in the ICA Proxy Mode http://support.citrix.com/article/CTX125718 … to determine whether you have maxed out your concurrent user sessions configured on the Access Gateway as shown in the following: Access -> Gateway -> Change authentication settings Note that you can also check to see how many active user sessions there are by navigating to: Access Gateway -> Active user sessions ------------------------------------------------------------------------------------------------------------------------------------------------------------------- http://terenceluk.blogspot.com/2012/04/attempting-to-launch-xendesktop-55-or.html I've also come across the situation where the NetScaler had no active sessions but was still suing evaluation licenses so when I went ahead to put the permanent licenses on, the error went away. Posted by Terence Luk at 7:05 PM Email ThisBlogThis!Share to TwitterShare to FacebookShare to Pinterest Labels: Citrix, XenApp, XenDesktop 1 comment: Brandon Hudson said... Found very cool and unique info here in this blog. This is a great addition in my favorite blog list.Lenovo - 15.6" ThinkPad Notebook - 4 GB Memory - 320 GB Hard Drive - BlackLenovo - 15.6" Laptop - 4GB Memory - 500GB Hard Drive - Black Textured February 27, 2014 at 4:01 AM Post a Comment Newer Post Older Post Home Subscribe to: Post Comments (Atom) Terence Luk Search My Blog Blog Archive ► 2016 (56) ► October (1) ► September (2) ► August (1) ► July (5) ► June (4) ► May (8) ► April (6) ► March (4) ► February (11) ► January (14) ► 2015 (78) ► December (10) ► November (11) ► October (1) ► September (2) ► August (3) ► July (2) ► June (11) ► May (1) ► April (9) ► March (14) ► February (7) ► January (7) ►
a Question Ask for Help Receive Real-Time Help Create a Freelance Project Hire for a Full Time Job Ways to Get Help Ask a Question Ask for Help Receive Real-Time Help Create a Freelance Project https://www.experts-exchange.com/questions/26820499/Cannot-connect-to-the-Citrix-Xenapp-server-protocol-Driver-Error.html Hire for a Full Time Job Ways to Get Help Expand Search Submit Close Search Login Join Today Products BackProducts Gigs Live Courses Vendor Services Groups Careers Store Headlines Website Testing Experts Exchange > Questions > Cannot connect to the Citrix Xenapp server. protocol Driver Error) Want to Advertise Here? Solved Cannot connect to the Citrix Xenapp server. protocol Driver Error) Posted on unable to 2011-02-14 Citrix Windows Server 2008 Microsoft IIS Web Server 2 Verified Solutions 26 Comments 7,582 Views Last Modified: 2012-05-11 Having difficulties accessing accessing Citrix Server / launching applications from the outside thru firewall. I can get to the Cirtix Logon Screen from the outside but after inicial login / authentication when I try and launch application It does not function appropriatly. Cannot lauch any unable to launch applications. Receive this error. (Unable to lauch your application. Contact your heldesk with the following information. Cannot connect to the Citrix Xenapp server. protocol Driver Error) The Website/Citrix is also using SSL Cert for HTTPS. Having some issues setting this up correctly "Manage secure client access" in "Citrix Access Management Console". I can access the Citrix environment from inside the firewall on the local network and access / launch applications without any issues running Citrix Apps from internal. Issue is only coming from public side. Also only port 80 and 443 is open on our juniper firewall. The Server is running (Windows 2008 Server 64-Bit, Citrix XenApp 5.0 Advanced Edition. The Server is connected to local network 192.168.x.x all of the Cirtix Modules / Applications are running a on 1 single Server/Box. Example: Private IP Internal 192.168.x.x NATs to 170.2.2.2 0 Question by:Tech_Me_More Facebook Twitter LinkedIn Google Best Solution byTech_Me_More Hi CarlWebster - Thanks for all your input, but I finally broke down and paid Citrix (an arm and a leg) to help resolve the problem. You had me on the right track, but the link you sent