Canon Pixma Mx870 Error 6502
Contents |
Unplug the printer. Remove the faulty Cartridge Plug in the printer and press and hold power button Keep it held down. Press Resume twice, and this should reset the fault. Solution 2: The last cartridge installed may be faulty. Install a new cartridge Solution 3: When error canon pixma mx870 error b200 is indicated, turn power switch off so green light is extinguished. Hold down resume button and hold
Canon Pixma Mx870 Error Code 6a80
down power button so both are held down at same time When green light comes on, continue holding down power button and let resume
Canon Pixma Mx870 Printer Error B200
button go, then press resume button twice. Let power button go. Press resume button four times, power button should be released before doing this. Wait until printer settles down, if power is off, turn on. If power will not come on,
Canon Pixma Mx870 Manual
remove power cord from back of printer, then wait 15 seconds before plugging back in again and turn power on. Solution 4 (thanks to Anniina for the tip !): Unplug the power cord. Remove all ink cartridges. Plug cord back in and turn the printer on. Replace all ink cartridges. Solution 4a (Thanks to Vis8): Lift the bottom part of the door (open) When the cartridge carriage comes to the center, remove all cartridges turn off the power Turn on the power After canon pixma mx870 ink the printer initialized, the cartridge carriage will come to the center again Replace the cartridges Close door Solution 5: Sometimes a waste ink pad reset solves the problem Libellés : Canon Pixma, Error code 22 comments: prestige said... Thanks alot. this method works!!! August 25, 2009 at 1:08 AM Edward Lorence said... Tried 10 times. Orange light is still flashing, printer will not work. Canon PG-5BK/CL-8 cartridge. Error mesaages 6502. I'm dead in the water. Never happened before. Have a stock of cartridges that I can't use. March 22, 2011 at 11:09 AM Mike Oncley said... I'm in the same boat as edward April 7, 2011 at 9:21 PM LEH said... Hi Mike and Edward,Two more solutions are added above.Good luck ! April 8, 2011 at 2:24 AM Unknown said... Where is the resume button on Canon MG6250? June 10, 2012 at 8:31 AM Anonymous said... Hahahaha... solution 3 is like the "secret cheat code" to make the printer work. If only it did.... November 21, 2012 at 11:11 PM Anniina said... None of these worked for me, but this is what did:1. Unplug the power cord.2. Remove all ink cartridges.3. Plug cord back in & turn printer on. 4. Put all ink cartridges in.That worked on mine; I hope it does on yours. January 22, 2013 at 12:53 PM Nguyên Phát Lê said... Hi guy, after several try, this is my conclusion:The printer head contact is dirty, try to clean it The "ink lev
6502 error message for iP4200/4300/4500 printers - how User Name Remember Me? Password Forum Home Register FAQ Today's Posts Search Search Forums Show Threads Show Posts canon pixma mx870 best buy Advanced Search Go to Page... Thread Tools Search this Thread Jan canon pixma mx870 driver mac 11, 2008, 12:43 AM #1 laikanuki Member Join Date: Jul 2005 Posts: 54 Sometimes the Canon canon pixma mx870 troubleshooting printers which use PG-5BK/CL-8 colour cartridges with chips will give error mesaages like 6502 or other types of error meaasge to do with the cartridges, which has the orange light http://fix-your-printer.blogspot.com/2009/03/error-code-6502-on-canon-printer.html flashing and the printer will not work. Follow this procedure which quite often resets the printer and allows it to resume printing. When error is indicated, turn power switch off so green light is extinguished. First hold down resume button and then hold down power button so both are held down at same time When green light comes on, continue http://forums.steves-digicams.com/photo-inkjet/135160-canon-6502-error-message-ip4200-4300-4500-printers-how.html holding down power button and let resume button go, then press resume button twice. Then let power button go. Then press resume button four times, power button should be releasedbefore doing this. Wait until printer settles down, if power is off, turn on. If power will not come on, remove power cord from back of printer, then wait 15 seconds before plugging back in again and turn power on. This normally solves the error problem - if not go through same procedure again. Incidentally, you may find that if the chips had previously been disabled,the low ink warnings are showing againand they will have to be disabled once more. This would indicate that the above procedure clears the firmware memory of the disabling of the chips, this may be usefull if you need some warranty work done on you printer after the chips had been disabled. Canon does warn that disabling the chips may result in the printer's warranty being voided Sponsored Links Jan 12, 2008, 9:29 AM #2 KnightCrawler Senior Member Join Dat
by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the http://www.justanswer.com/printers/5f2pe-mx870-printer-showing-error-message-6502-i-think.html answer you receive. Ask Andy Your Own Question Andy, Elec & Comp pro Category: Printers Satisfied Customers: 23538 Experience: 11yr exp, Comp Engg, Internet expert, Web developer, SEO 16465236 Type Your Printers Question Here... Andy is online now I have an mx870 printer showing an error message 6502. I think Resolved Question: I have an mx870 printer showing an error message 6502.I think the contacts for the ink cartridges might need cleaning. canon pixma How do I do this?thanks Submitted: 5 years ago. Category:Printers Share this conversation Expert: Andy replied5 years ago. Hello,Welcome to JustAnswer !! I am Andy and I will be glad to help you out with your issue today.The error 6502 is a "Ink tank position sensor error".Behind the cartridges, you will find a thin plastic tape going across left to right. Clean up that tape with a soft moist cloth.If that canon pixma mx870 does not resolve the issue, than the printer needs to be repaired.If not in warranty, it would be cheaper to buy a new printer.In some cases it also happens due to malfunctioning cartridges. So you will have to replace the cartridges to confirm that. Feel free to ask any question or concern you may have. I will be glad to help you.Please click "ACCEPT" so that I get paid.(You need to click ACCEPT even if you are a SUBSCRIPTION or TRIAL member)Positive Feedback and BONUS are always appreciated.Andy Andy, Elec & Comp pro Category: Printers Satisfied Customers: 23538 Experience:11yr exp, Comp Engg, Internet expert, Web developer, SEO Andy and 3 other Printers Specialists are ready to help you Ask your own question now Share this conversation JustAnswer in the News: Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com. JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance. Web sites like justanswer.com/legal...leave nothing to chance. Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.