Dell Optiplex Xe Error Codes
Contents |
OptiPlex XE Small Form Factor Service manual Dell OptiPlex XE Small Form Factor Service Manual: Diagnostic Lights Hide thumbs 1 2 3 4 5 6 7 8 9 10 dell optiplex xe power light flashing 11 12 13 14 15 16 17 18 19 20 21 22 23 24 dell optiplex xe 1 and 3 flashing 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 3-3-2 Invalid NVRAM configuration 3-3-4 Video dell optiplex xe specs Memory Test failure 3-4-1 Screen initialization failure 3-4-2 Screen retrace failure 3-4-3 Search for video ROM failure 4-2-1 No timer tick 4-2-2 Shutdown failure 4-2-3 Gate A20 failure 4-2-4 Unexpected interrupt in protected mode 4-3-1 dell optiplex xe manual Memory failure above address 0FFFFh 4-3-3 Timer-chip counter 2 failure 4-3-4 Time-of-day clock stopped 4-4-1 Serial or parallel port test failure 4-4-2 Failure to decompress code to shadowed memory 4-4-3 Math-coprocessor test failure 4-4-4 Cache test failure Diagnostic Lights To help troubleshoot a problem, your computer has four lights labeled 1, 2, 3, and 4 on the bank panel. When the computer starts normally, the lights flash before turning off. If the
Dell Optiplex Xe Bios
computer malfunctions, the sequence of the lights help to identify the problem. NOTE: After the computer completes POST, all four lights turn off before booting to the operating system. Light Pattern Problem Description The computer is in a normal off condition or a possible pre-BIOS failure has occurred. The diagnostic lights are not lit after the computer successfully boots to the operating system. A possible processor failure has occurred. Memory modules are detected, but a memory failure has occurred. A possible graphics card failure has occurred. A possible floppy drive or hard drive failure has occurred. A possible USB failure has occurred. Reinstall all USB devices and check all cable connections. No memory modules are detected. Memory modules are detected, but a memory configuration or compatibility error has occurred. A possible expansion card failure has occurred. Another failure has occurred. Suggested Resolution Plug the computer into a working electrical outlet. l If the problem persists, contact Dell. l Reseat the processor (see Processor information for your computer). l If the problem persists, contact Dell. l If two or more memory modules are installed, remove the modules, then reinstall one module l and restart the computer. If the computer starts normally, continue to install additional memory modules (one at a
OptiPlex XE Service manual Dell OptiPlex XE Service Manual: Beep Codes Hide thumbs Also See for OptiPlex XE Service manual - 10 pagesSetup & features manual - 8 pagesConfiguration -
Dell Optiplex Xe Ram
6 pages 1 2 3 4 5 6 7 8 9 dell optiplex xe motherboard 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 dell optiplex xe review 31 32 33 34 35 36 37 38 39 40 41 42 43 2. If a problem is encountered during a test, a message appears with an error code and a description of https://www.manualslib.com/manual/553424/Dell-Optiplex-Xe-Small-Form-Factor.html?page=13 the problem. Write down the error code and problem description and follow the instructions on the screen. 3. If you run a test from the Custom Test or Symptom Tree option, click the applicable tab described in the following table for more information. Tab Function Results Displays the results of the test and any error conditions encountered. Errors Displays error conditions encountered, error codes, and the problem description. https://www.manualslib.com/manual/678398/Dell-Optiplex-Xe.html?page=12 Help Describes the test and may indicate requirements for running the test. Configuration Displays your hardware configuration for the selected device. The Dell Diagnostics obtains configuration information for all devices from system setup, memory, and various internal tests, and it displays the information in the device list in the left pane of the screen. The device list may not display the names of all the components installed on your computer or all devices attached to your computer. Parameters Allows you to customize the test by changing the test settings. 4. When the tests are completed, if you are running the Dell Diagnostics from the Drivers and Utilities disc, remove the disc. 5. Close the test screen to return to the Main Menu screen. To exit the Dell Diagnostics and restart the computer, close the Main Menu screen. Power Button Light Codes The diagnostic lights give much more information about the system state, but legacy power light states are also supported in your computer. The power light states are shown in following table. Power Light State Off Power is off, light is blank. Blinking Amber Initial state of light at power up. Indicates system has power, but the POWER_GOOD signal is not yet
& PowerVault Main Line http://tektip.blogspot.com/2010/04/dell-optiplex-light-code-and-beep-code.html 1800-0600-09 Thailand Toll-free (AIS & TOT Telco) 1800-060-157 Thailand Toll-free(CAT, True & DTAC Telco) dell optiplex 001-800-601-5623 Thailand Customer Care Toll Free 1800-006-006 Press: 2 & Press: 5 Local Landline Call dell optiplex xe 02-6707000 Press 2 & Press 1 Ext: 2133416 Technical Support จะถามอยู่ 3 คำถามคือ 1. ไฟ Power ติดสีอะไร และกระพริบหรือไม่ 2. ไฟ Diagnostic Light ติดที่หมายเลขอะไรบ้าง 3. ได้ยินเสียง Beep ด้วยหรือเปล่า System Lights Your power button light and hard-drive light may indicate a computer problem. Power Light Problem Description Suggested Resolution Solid greenPower is on, and the computer is operating normally. On the desktop computer, a solid green light indicates a network connection.No corrective action is required. Blinking greenThe computer is in a power-saving mode (Microsoft® Windows® XP).Press the power button, move the mouse, or press a key on the keyboard to wake the computer. Blinks green several times and then turns offA configuration error exists.Check the diagnostic lights to see if the specific problem is identified (see Diagnostic Lights). Solid yellowThe Dell Diagnostics is running a test, or a device on the system board may be faulty or incorrectly installed.If the Dell Diagnostics is running, allow the testing to complete. If the computer does not boot, contact Dell for technical assistance (see Contacting Dell). Blinking yellowA power supply or system board failure has