No Disk Error Dvd
Contents |
What Do I Need to Clean a DVD Laser Lens? How to Clean the Laser Pickup Lens on your DVD Player How to Fix a Scratch on a PlayStation CD lg dvd player disc error message How to Unjam a CD Player How to Get an MP3 Player to Work dvd player not spinning When It Is Dead How to Fix a Philips CD Changer You've popped the popcorn, poured a glass of your
No Disc Error Cd Player
favorite beverage and settled in to watch a movie, but when you press "Play" on the remote control, the dreaded "NO DISC" error appears on your DVD player. If you're lucky, you may be
Dvd Laser Lens Cleaning Disc
able to correct the problem by just opening and closing the disc tray on the player and trying again. If you're really unlucky, your DVD player might be defective. However, more often than not, a scratched or smudged disc or a dirty laser lens in the player is usually the cause of the error, and is something you may be able to fix in a few minutes. dvd player in tv says no disc Correcting Common Disc Problems Press the "Eject" or "Open" button on the DVD player to disc tray to determine if it opens easily and does not appear jammed or hindered. If the disc tray appears to open slower than usual or fails to open, the disc may not sit flush in the tray or otherwise be seated properly. Use your hand to pull out the disc tray slowly if it does not open on its own and then reseat the disc. Close the disc tray and press "Play" on the DVD player again to see if reseating the disc in the tray corrects the "NO DISC" error. Power off the DVD player, then back on again. Attempt to play the DVD disc normally. Sometimes, an error in the DVD player firmware may prevent the device from reading discs properly. When this occurs, resetting the player often corrects "NO Disc" errors. Remove the disc from the DVD player. Use a lint-free cloth and some denatured alcohol or water to clean the disc and remove any dust or smudges that may prevent the player from reading it properly. Reinsert the disc into the player and press "Play" to see if cleaning the di
What Do I Need to Clean a DVD Laser Lens? How to Clean the Laser Pickup Lens on your DVD Player How to Fix a Scratch on a PlayStation CD How to Unjam a CD Player How to Get an MP3 Player to Work When It Is Dead How to Fix a Philips
Philips Portable Dvd Player Says No Disc
CD Changer You've popped the popcorn, poured a glass of your favorite beverage and settled in to dvd player wont read any disc watch a movie, but when you press "Play" on the remote control, the dreaded "NO DISC" error appears on your DVD player. If you're lucky, you may my magnavox dvd player says disc error be able to correct the problem by just opening and closing the disc tray on the player and trying again. If you're really unlucky, your DVD player might be defective. However, more often than not, a scratched or smudged disc or a dirty laser lens http://techin.oureverydaylife.com/fix-nodisc-error-dvd-player-1786.html in the player is usually the cause of the error, and is something you may be able to fix in a few minutes. Correcting Common Disc Problems Press the "Eject" or "Open" button on the DVD player to disc tray to determine if it opens easily and does not appear jammed or hindered. If the disc tray appears to open slower than usual or fails to open, the disc may not sit flush in the tray or otherwise be seated properly. Use your hand to pull out the disc tray http://techin.oureverydaylife.com/fix-nodisc-error-dvd-player-1786.html slowly if it does not open on its own and then reseat the disc. Close the disc tray and press "Play" on the DVD player again to see if reseating the disc in the tray corrects the "NO DISC" error. Power off the DVD player, then back on again. Attempt to play the DVD disc normally. Sometimes, an error in the DVD player firmware may prevent the device from reading discs properly. When this occurs, resetting the player often corrects "NO Disc" errors. Remove the disc from the DVD player. Use a lint-free cloth and some denatured alcohol or water to clean the disc and remove any dust or smudges that may prevent the player from reading it properly. Reinsert the disc into the player and press "Play" to see if cleaning the disc fixes the "NO DISC" error. Cleaning the DVD Laser Lens Power off the DVD player and disconnect all cables. Use your fingers to open the disc tray door slowly and gently. Alternatively, insert a pin or straightened paper clip into the small "Manual Eject" hole next to the disc tray if the unit has one. Use a can of compressed air to blow out the inner area of the DVD player exposed by opening the disc tray. Use short bursts of air from the can to clean out any dust or residue that may be covering the laser lens and preventing the player from reading discs. Allow any moisture created by the canned air to dry a few minutes before continuing. Reconnect all cables to the DVD player and power on the
Error on a DVD Player How to Fix a No-Disc Error on a DVD Player By eHow Electronics Editor eHow Contributor eHow Electronics Editor Follow Pin Share Tweet Share Email Save Tired of seeing the no-disc error every time you try to watch a movie? No-disc http://www.ehow.com/how_2036277_fix-error-dvd.html errors are usually caused when the DVD or the laser-lens pickup has become dirty and causes the http://fixitdvdplayerreadsnodisk.blogspot.com/ DVD player to not be able to read the DVD. Follow these steps to find out how to fix a no-disc error on a DVD player. Other People Are Reading How to Clean the Laser Pickup Lens on your DVD Player How to Clean DVD Heads Things You'll Need Isopropyl alcohol Lens cleaning disc Check the disc you're using for scratches and dirt. If the disc is damaged it dvd player won't play properly, regardless of the DVD player's ability to function. You can use a DVD repair device like the "Disc Doctor" to repair the DVD or purchase a new DVD. Make sure the discs you're using fit the correct format specified by your DVD player. For example, if your DVD player doesn't support home-burned DVD-R's, then you can't use a DVD that you made at home. You may need to upgrade to a newer model, most of which accept the latest DVD formats. Clean the laser says no disc lens with a DVD laser lens cleaning disc. DVD laser lens cleaning discs can be purchased at most electronics retailers or online. Insert the laser lens cleaning disc and follow the instructions. Insert a correctly-formatted, undamaged disc into your player. Listen to see if it begins to read the disc. If it continues to make no sound and gives you the same message, then the problem is probably that your disc is not spinning in the device. Turn the device off and unplug it. Take off the outer casing by removing the three or four screws and lifting the top piece off. This will allow you to see if anything is simply stuck or jammed. If this is the case, a simple nudge back to the correct position will fix the problem. Clean the lens while the DVD player is open. A dirty lens is most likely the cause of your no-disc error. The lens should be cleaned with isopropyl alcohol and a cotton swab. Take your DVD player to have it professionally fixed only when none of these other solutions solves the problem. A professional repair technician will be able to tell you if fixing your DVD player is worth the money. Tips & Warnings If you open the DVD player and find you don't know anything about what you see, it might be best to have a professional take a look at it instead. Always keep the DVD player unplugged when you open it up. If a DVD player's spindle or laser lens are damaged, it's us
can be cleaned with a clothe moistened with alcohol. A cotton bud will do also. Just gently wipe it on the lens. You probably would have to open the cover of the DVD player. Inside this unit you will find the mechanical loading disc tray. The one where disc is loaded that moves in and out when ejecting or inserting the disk. In the middle of the mechanical loading you will find a spindle motor and beside this is a small glass illuminating red when the unit is on. This is the lens. Clean it with a cotton bud moistened with alcohol. You may also need to check the ribbon wire. It is important, cause it's the one that connects the lens and the CPU. Replace it with a new one if possible. It is good to check then secure also the connectors from the board and to the mechanical system. These are the things to consider when a " No Disk " error appear on your DVD player when you load a playing DVD disk. Posted by Gadgetgeek at 11:46 PM 0 comments Email ThisBlogThis!Share to TwitterShare to FacebookShare to Pinterest Labels: DVD player Home Subscribe to: Posts (Atom) Fix It! DVD Player reads " no disk " Loading... About Me Gadgetgeek View my complete profile Blog Archive May (1) Support this Blog Total Pageviews There was an error in this gadget Amazon Contextual Product Ads Amazon Deals Picture Window template. Powered by Blogger.