Error During Setting The Fuses. Flashing Of Firmware Aborted
Vendors Navigate Blogs Classifieds Places Search Go to Page... Remember Me Forgot Password? Aircraft - Electric - Multirotors Multirotor Talk Help! Please help! KK Blackboard firmware flashing Thread Tools Jun 16, 2011, 08:19 PM #1 bamm bamm Registered User Planet Jupiter Joined Jan 2005 1,746 Posts Help! Please help! KK Blackboard firmware flashing Hi all. I have built my quad and it's all ready to go but I can't flash the firmware onto my KK blackboard. I have never hooked ESC power to the quad, the first initial power I have ever applied was through the USB dongle. I have tried using the program I received in an email from the seller and it is called ProgISP. I have installed the driver for the USB dongle and verified it is working properly on my computer. I am following the instructions I received from the seller on how to flash the firmware to the Blackboard and everytime I get to a certain step in the process, I click "READ" and the USB dongle flashes a RED light then the Blackboard flashes it's blue light, Right away I get a message saying "CHIP ENABLE PROGRAM ERROR". I have also tonight tried installing KK MultiCopter flash tool and when I try flashing the board, the dongle flashes red, and the blackboard flashes blue. Then I get this message in the script; Flash the firmware from repository. C:\Documents and Settings\RCBamm\My Documents\My Pictures\QuadcopterKK\lib\avrdude\windows\avrdude. exe -C C:\Documents and Settings\RCBamm\My Documents\My Pictures\QuadcopterKK\lib\avrdude\windows\avrdude. conf -p m168 -P usb -c usbasp -B 8 -U lfuse:w:0xe2:m -U hfuse:w:0xde:m found 2 busses avrdude.exe: error: programm enable: target doesn't answer. 1 avrdude.exe: initialization failed, rc=-1 Double check connections and try again, or use -F to override this check. avrdude.exe done. Thank you. Error during setting the fuses. Flashing of firmware aborted. I have read alot so far, and I can't really get a straight explaination. I so want to fly my quad, I am just trying to flash the V1.7 Xcopter firmware to my board Sign up now to remove ads between posts Jun 16, 2011, 09:24 PM #2 pug398 pug398 Registered User VA Joined Nov 2009 2,814 Posts Depending on the programmer, it may or may not power the chip. Connect an esc to board and power it up so the bec will power the chip for sure. Sep 22, 2011, 08:41 AM #3 Jamesse007 Jamesse
the same error C:\Users\Daryl\Desktop\KK board\lib\avrdude\windows\avrdude.exe -C C:\Users\Daryl\Desktop\KK board\lib\avrdude\windows\avrdude.conf -p m168p -P usb -c usbasp -B 8 -e -U lfuse:w:0xe2:m -U hfuse:w:0xde:m avrdude.exe: error: could not find USB device with vid=0x16c0 pid=0x5dc vendor='www.fischl.de' product='USBasp' avrdude.exe done. Thank you. Error during setting the fuses. Flashing of firmware aborted. Ive gone through multiple support forums and followed every bit of instruction and followed driver instal instruction. It never works, it cant see the USBasp programer. One this I did differently from Davids instruction is plug the connector directly into the board because the new programmer now comes with a 6 pin header and its supposed to work with this programmer and kk board combo. I http://www.rcgroups.com/forums/showthread.php?t=1456741 believe this because the board does power up(flashes one red led once) and it provides power to my rx. Any help you guys can provide would be awesome. ...im down to a point where I just want to mail the HK kk board to someone who has got it to work to have them program it for me. Or meet up if you are near the San Antonio area. h0tr0d24th April 2012, 03:09 PMThat didn't work http://fpvlab.com/forums/archive/index.php/t-5180.html with my friends HK kk board either. I had to use a different program to get it to flash. I used the usbasp programmer. Let me see if I've got the program I used laying around somewhere. Try this one: http://lazyzero.de/en/modellbau/kkmulticopterflashtool And if that doesn't work let me know and I'll dig up that chinese program I used lol. SilviaSGP0624th April 2012, 03:23 PMawesome thanks, Ill try it when I get off from 'work'. IF you do however get bored and want to search and send the program anyway you can send it to. h0tr0d24th April 2012, 03:28 PMShot the program over to you along with the instructions. You should probably remove that email address before a spam bot catches it. :D -Pat SilviaSGP0624th April 2012, 04:13 PMdone, and thanks man! SilviaSGP0624th April 2012, 06:42 PMthe first link turned out to be one of the places I tried, so Ill try what you sent me. SilviaSGP0624th April 2012, 07:41 PMGood news, I was able to flash it! bad news, I cant seem to arm in when using any Minsoo Kim firmwares. The kaptienkuk firmware will arm but doesnt work right (the rear motor does not activate without alot of throttle or a sudden tilt forward) Is there any one on here that is flying a tricopter with a HobbyKing Multi-Rotor Control Board V2.1? that can shed
But I was not able to flash it and got an error from the flash software. After that the board shows no response when I connect esc's or usbasp programming http://www.rcindia.org/servos-gyros-and-all-electronics/kkmulticopter-v5-5-not-working/?action=printpage cable, led is not blinking. Please help.. Title: Re: kkmulticopter v5.5 not working. Post http://rcexplorer.se/educational/2011/10/changing-the-firmware-on-a-hobbyking-kk-board/ by: SideWinder on March 04, 2014, 07:41:42 PM What was the error you had encountered, and are you sure you didnt reverse polarity or connect wrong pins up while flashing or powering up after failed flash attempt. Because if its not powering up at all, its kind of dead. Try to power it with different esc/usb port/cable error during etc Title: Re: kkmulticopter v5.5 not working. Post by: avesh on March 04, 2014, 08:18:12 PM I tried using libusb and kk flash utitlity and it worked like a charm. Now the board is flashed with kk blackboard 16kb flash..avrdude.exe done. Thank you. Title: Re: kkmulticopter v5.5 not working. Post by: giri111820 on March 04, 2014, 09:19:55 PM Flash the firmware from repository.C:\Users\HP\Desktop\kk board\lib\avrdude\windows\avrdude.exe -C C:\Users\HP\Desktop\kk board\lib\avrdude\windows\avrdude.conf -p m168p -P usb error during setting -c usbasp -e -U lfuse:w:0xe2:m -U hfuse:w:0xdd:m avrdude.exe: warning: cannot set sck period. please check for usbasp firmware update.avrdude.exe: error: usbasp_transmit: usb_control_msg: sending control message failed, win error: The I/O operation has been aborted because of either a thread exit or an application request.avrdude.exe: error: programm enable: target doesn't answer. 0 avrdude.exe: initialization failed, rc=-1 Double check connections and try again, or use -F to override this check.avrdude.exe: error: usbasp_transmit: usb_control_msg: sending control message failed, win error: A device attached to the system is not functioning.avrdude.exe done. Thank you.Error during setting the fuses.Flashing of firmware aborted.i encounter this problem can anyone help with this Title: Re: kkmulticopter v5.5 not working. Post by: avesh on March 04, 2014, 09:47:19 PM Yes i had the same problem.. You need to download libusb ~1.2 then follow these stepshttp://www.youtube.com/watch?v=dkOQ6tlGgyU#ws (http://www.youtube.com/watch?v=dkOQ6tlGgyU#ws)just verify the polarity of the usbasp cable. Tiny arrow on the jack should be up against vcc (board). Title: Re: kkmulticopter v5.5 not working. Post by: giri111820 on March 04, 2014, 10:17:39 PM Flash the firmware from repository.C:\Users\HP\Desktop\kk board\lib\avrdude\windows\avrdude.exe -C C:\Users\HP\Desktop\kk board\lib\avrdude\windows\avrdude.conf -p m168p -P usb -c usbasp-clone -e -U lfuse:w:0xe2:m -U hfuse:w:0xdd:m avrdude.exe: warning: cannot set sck period. please check for usbasp firmware update.avrdude.exe:
- David This guide is made for the Hobbyking KK board V1 but will work just the same for the Hobbyking KK board V2, the only difference is that you have to select the correct board in the flash tool (The V2 uses a different processor). The V2 board is capable of running more advanced firmwares like the XX, where as the V1 is limited to the ”standard” firmwares. The HK KK boards comes pre-flashed with the ”+” Quad KK firmware. In this guide we will change it to the Tricopter V1.6 firmware. You need two things to change the firmware of the HK KK board: First thing is an AVR programmer. I use this AVR programmer from Flytron. But you can get one really cheap from Hobbyking or ebay. Search for ”usbasp” or ”AVR Programmer” and you’ll find loads. Second thing you need is an adaptor. Normally the AVR programmers comes with the standard 10 pin output, but the HK KK is 6 pins. Luckily the adapter is so easy to make that anyone can do it. (Picture by arch001) On the left you see the output from the 10 pin AVR programmer and on the left the 6 pin port of the HK KK board. All you need to do is connect the correct pins to each other. 1 to 9, 2 to 2, 3 to 7, 4 to 1, 5 to 5 and 6 to 10. (Picture by arch001) I soldered my own adapter but there is a simpler way that doesn’t require any soldering That way is to use two servo extensions. Simply remove the protective plastic and pull the pins out. Plug the pins into the connector in the right order and you’re done. Just make sure that the pins doesn’t touch each other. If you like to make the adapter reusable you can add some hotglue on the pins so that you don’t have to plug each pin in separately next time. (Pin position in the picture is only for illustrative purposes) Now that you have you’re KK board hooked up to the AVR programmer you need an AVR flashing software. There are a number of different options to choose from but I higly recommend using the KKmulticopter Flash tool. This software is specifically made to flash KK boards and is extremely simple to use. You don’t have to know about fuses or anything. The software even fetches the firmware file for you. And one of the best things, it works on both PC and MAC. Download and install the software from this page. Install the proper drive