Ftp 246 Error
Contents |
good, bad or incomplete: Range Purpose 1xx Positive Preliminary reply The requested action is being initiated; expect another reply before proceeding with a new command. (The user-process sending another command ftp error codes before the completion reply would be in violation of protocol; but server-FTP processes
Ftp Error 426
should queue any commands that arrive while a preceding command is in progress.) This type of reply can be used ftp return codes mainframe to indicate that the command was accepted and the user-process may now pay attention to the data connections, for implementations where simultaneous monitoring is difficult. The server-FTP process may send at most, one
Ftp Error 500
1xx reply per command. 2xx Positive Completion reply The requested action has been successfully completed. A new request may be initiated. 3xx Positive Intermediate reply The command has been accepted, but the requested action is being held in abeyance, pending receipt of further information. The user should send another command specifying this information. This reply is used in command sequence groups. 4xx Transient Negative Completion reply The ftp error 421 command was not accepted and the requested action did not take place, but the error condition is temporary and the action may be requested again. The user should return to the beginning of the command sequence, if any. It is difficult to assign a meaning to "transient", particularly when two distinct sites (Server- and User-processes) have to agree on the interpretation. Each reply in the 4xx category might have a slightly different time value, but the intent is that the user-process is encouraged to try again. A rule of thumb in determining if a reply fits into the 4xx or the 5xx (Permanent Negative) category is that replies are 4xx if the commands can be repeated without any change in command form or in properties of the User or Server (e.g., the command is spelled the same with the same arguments used; the user does not change his file access or user name; the server does not put up a new implementation.) 5xx Permanent Negative Completion reply The command was not accepted and the requested action did not take place. The User-process is discouraged from repeating the exact request (in the same sequence). Even some "permanent" error conditions can
Start here for a quick overview of the site Help Center Detailed answers to any questions you might have Meta
Ftp Error 550 Failed To Open File
Discuss the workings and policies of this site About Us Learn
Ftp Error 421 Service Not Available
more about Stack Overflow the company Business Learn more about hiring developers or posting ads with us ftp 530 Server Fault Questions Tags Users Badges Unanswered Ask Question _ Server Fault is a question and answer site for system and network administrators. Join them; it only takes a https://en.wikipedia.org/wiki/List_of_FTP_server_return_codes minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the top FTP client receives whole file, but always closes connection before finishing up vote 6 down vote favorite On a Windows Server 2008 R2 Standard machine, I'm having trouble connecting to and downloading http://serverfault.com/questions/595370/ftp-client-receives-whole-file-but-always-closes-connection-before-finishing a file from a Windows FTP server. Filesize is ~3KB to 6KB. Very rarely ~100KB to ~500KB, but the server has plenty of space on disk. I've tried a passive connection: Response: 220-Microsoft FTP Service Response: 220 Regal Logistics Command: USER ******** Response: 331 Password required for ********. Command: PASS ******** Response: 230 User ******** logged in. Status: Connected Status: Starting download of /********/PO/201405130227.xml Command: CWD /********/PO Response: 250 CWD command successful. Command: TYPE A Response: 200 Type set to A. Command: PASV Response: 227 Entering Passive Mode (***,***,***,**,19,64) Command: RETR 201405130227.xml Response: 125 Data connection already open; Transfer starting. Response: 426 Data connection closed. Error scanning content Error: File transfer failed after transferring 3,465 bytes in 1 second The strange thing is that the file is 3,465 bytes, so the entire file is getting through, it just isn't finishing up properly. And I've tried an active connection: Response: 220-Microsoft FTP Service Response: 220 Regal Logistics Command: USER ******** Response: 331 Password required for ********. Command: PASS ******** Response: 230
CommunityOracle User Group CommunityTopliners CommunityOTN Speaker BureauJava CommunityError: You don't have JavaScript enabled. This tool https://community.oracle.com/thread/552284?start=0 uses JavaScript and much of it will not work correctly without it enabled. Please turn JavaScript back on http://forum.odin.com/threads/error-ftp-backup.262951/ and reload this page. Please enter a title. You can not post a blank message. Please type your ftp error message and try again. More discussions in Integration - InterConnect All PlacesOracle CommunityArchived ForumsIntegration - InterConnect This discussion is archived 1 Reply Latest reply on Sep 4, 2007 8:22 PM by 596264 Error in ftp receiver monitor ftp error 421 595837 Aug 31, 2007 9:06 PM Kind people, I'm getting this error with an InterConnect FTP adapter (the adapter is on one box, the directory it reads from on another box): Transport logs: [IPT_FileRecMonitorError] Error in ftp receiver monitor. oracle.oai.agent.adapter.transport.TransportException: Unable to enter passive mode. rc = 425 425 Can't open passive connection: Too many open files. at oracle.oai.agent.adapter.transport.basic.ftp.FTPAgent.getFileList(FTPAgent.java:259) at oracle.oai.agent.adapter.transport.basic.FileSource.getFileList(FileSource.java:210) at oracle.oai.agent.adapter.transport.basic.FileSourceMonitor.processMessages(FileSourceMonitor.java:399) at oracle.oai.agent.adapter.transport.basic.FileSourceMonitor.run(FileSourceMonitor.java:185) Caused by: java.io.IOException: Unable to enter passive mode. rc = 425 425 Can't open passive connection: Too many open files. at oracle.oai.agent.adapter.transport.basic.ftp.FTPClient.establishDataConnection(FTPClient.java:206) at oracle.oai.agent.adapter.transport.basic.ftp.FTPClient.listFiles(FTPClient.java:431) at oracle.oai.agent.adapter.transport.basic.ftp.FTPAgent.getFileList(FTPAgent.java:253) It seems to me (maybe) that what is happening is that InterConnect is not closing the F
Windows Issues, Fixes, How-To' started by migarcia, Sep 11, 2012. migarcia Bit Poster Messages: 5 When I try to backup and send it via ftp, tells me the following error