Ftp Error 200 S Ok
Contents |
good, bad or incomplete: Range Purpose 1xx Positive Preliminary reply The requested action is being initiated; expect another reply before proceeding with a new command. (The user-process sending another command before the completion ftp error codes reply would be in violation of protocol; but server-FTP processes should queue any commands
Ftp Error 426
that arrive while a preceding command is in progress.) This type of reply can be used to indicate that the command ftp return codes mainframe was accepted and the user-process may now pay attention to the data connections, for implementations where simultaneous monitoring is difficult. The server-FTP process may send at most, one 1xx reply per command. 2xx Positive Completion ftp error 421 service not available reply The requested action has been successfully completed. A new request may be initiated. 3xx Positive Intermediate reply The command has been accepted, but the requested action is being held in abeyance, pending receipt of further information. The user should send another command specifying this information. This reply is used in command sequence groups. 4xx Transient Negative Completion reply The command was not accepted and the requested action did not
Ftp Error 500
take place, but the error condition is temporary and the action may be requested again. The user should return to the beginning of the command sequence, if any. It is difficult to assign a meaning to "transient", particularly when two distinct sites (Server- and User-processes) have to agree on the interpretation. Each reply in the 4xx category might have a slightly different time value, but the intent is that the user-process is encouraged to try again. A rule of thumb in determining if a reply fits into the 4xx or the 5xx (Permanent Negative) category is that replies are 4xx if the commands can be repeated without any change in command form or in properties of the User or Server (e.g., the command is spelled the same with the same arguments used; the user does not change his file access or user name; the server does not put up a new implementation.) 5xx Permanent Negative Completion reply The command was not accepted and the requested action did not take place. The User-process is discouraged from repeating the exact request (in the same sequence). Even some "permanent" error conditions can be corrected, so the human user may want to direct his User-process to reinitiate the command sequence by direct acti
Free SFTP, SCP and FTP client for Windows News Introduction SSH Client SFTP Client FTP Client Download Install Donate Documentation Guides F.A.Q. Scripting .NET & COM Library Screenshots Translations Support Forum could not retrieve directory listing ftp Tracker History Topic "Cant FTP: Error listing directory" [Reply to topic] sftp error codes [Log in] [Forum Index] [Forum "Support and Bug Reports"] [Previous topic] [Next topic] Author Message anjanesh [View
Ftp 530
user's profile] Joined: 2007-11-10 Posts: 4 Location: Mumbai, India Posted: 2007-11-10 10:28 Cant FTP: Error listing directory [Reply with quote] Hi Im trying to connect to a remote https://en.wikipedia.org/wiki/List_of_FTP_server_return_codes server via FTP (port 21) but I get this this error msg : Code: Timeout detected. Could not retrieve directory listing PORT command successful Error listing directory '/'. I tried connecting to various linux hosts but all returned the same msg. But SFTP works though. WinSCP 4.0.4 Is there some setting I got to use to http://winscp.net/forum/viewtopic.php?t=5070 connect via FTP ? Thanks Advertisements G Jones Guest Posted: 2007-11-11 21:40 [Reply with quote] I am getting the same error - I was hoping 4.05 was going to work on my w98se system - as I had failed to get it working due to a netapi32 problem previously. Quote: Timeout detected. Could not retrieve directory listing PORT command successful Error listing directory '/'. martin [View user's profile] Site Admin Joined: 2002-12-10 Posts: 24665 Location: Prague, Czechia Posted: 2007-11-13 Re: Cant FTP: Error listing directory [Reply with quote] anjanesh wrote: Im trying to connect to a remote server via FTP (port 21) but I get this this error msg : Code: Timeout detected. Could not retrieve directory listing PORT command successful Error listing directory '/'. I tried connecting to various linux hosts but all returned the same msg. But SFTP works though. WinSCP 4.0.4 Is there some setting I got to use to connect via FTP ? Have you tried passive mode?_________________Martin Prikryl anjanesh [View user's
» FTP Status and Error Codes FTP Status and Error Codes Last Year GlobalSCAPE 5 CuteFTP for Windows THE INFORMATION IN THIS ARTICLE APPLIES TO: EFT Server all versions CuteFTP® all versions DISCUSSION During FTP sessions, servers https://kb.globalscape.com/KnowledgebaseArticle10142.aspx send and receive various numbered codes to/from FTP clients. Some codes represent errors, most others simply communicate the status of the connection. Below are brief explanations for the most common https://tools.ietf.org/html/draft-bryan-ftp-lock status and error codes. When determining a course of action, review the entire log; some codes are informational only, others indicate that you have entered the wrong information, and others indicate ftp error what the information is that you need to provide before continuing. For troubleshooting CuteFTP connection problems, also refer to Troubleshooting CuteFTP Connection Problems. The table below is provided so that you have some idea whether you can solve the issue on your own (e.g., code 331=you need to provide a password) or you need to call your ISP for assistance (e.g., code ftp error codes 426=you are unable to connect to the remote server). These codes are used by most FTP servers/clients. NOTE: The information below is only offered as a courtesy to assist you in telling your Internet Service Provider what the error is so that they can help solve your issue. For example, if you get a code 426, the transfer was aborted and the connection closed. The solution to this error is to "try logging back in; contact your hosting provider to check if you need to increase your hosting account; try disabling the firewall on your PC to see if that solves the problem. If not, contact your hosting provider or ISP." The list below contains standard FTP codes. Numbers outside this list are proprietary to the Server or Client that you are using. Code Description Discussion 100 Series The requested action was initiated; expect another reply before proceeding with a new command. 110 Restart marker reply. The text is exact and not left to the particular implementation; it must read "MARK yyyy = mmmm" where yyyy is User-process data stream marker, and mmmm
LOCK Command for Using a Single Port draft-bryan-ftp-lock-02 Abstract One of the biggest hurdles for FTP in real life usage is its use of two connections. First, it uses a primary connection to send control commands on, and when it sends or receives data, it opens a second TCP stream for that purpose. This document specifies a new FTP LOCK command to be used by clients to request the server to use the control connection for data transfers, using a single port instead of two. Editorial Note (To be removed by RFC Editor) Discussion of this draft should take place on the FTPEXT2 working group mailing list (ftpext@ietf.org), although this draft is not a WG item. Related documents (including fancy diffs) can be found at