Ftp Error 99
Contents |
good, bad or incomplete: Range Purpose 1xx Positive Preliminary reply The requested action is being initiated; expect another reply
Ftp Error Codes
before proceeding with a new command. (The user-process sending another command sftp error codes before the completion reply would be in violation of protocol; but server-FTP processes should queue any commands
Ftp Error 426
that arrive while a preceding command is in progress.) This type of reply can be used to indicate that the command was accepted and the user-process may sftp error code 255 now pay attention to the data connections, for implementations where simultaneous monitoring is difficult. The server-FTP process may send at most, one 1xx reply per command. 2xx Positive Completion reply The requested action has been successfully completed. A new request may be initiated. 3xx Positive Intermediate reply The command has been accepted, but the requested action ftp return codes mainframe is being held in abeyance, pending receipt of further information. The user should send another command specifying this information. This reply is used in command sequence groups. 4xx Transient Negative Completion reply The command was not accepted and the requested action did not take place, but the error condition is temporary and the action may be requested again. The user should return to the beginning of the command sequence, if any. It is difficult to assign a meaning to "transient", particularly when two distinct sites (Server- and User-processes) have to agree on the interpretation. Each reply in the 4xx category might have a slightly different time value, but the intent is that the user-process is encouraged to try again. A rule of thumb in determining if a reply fits into the 4xx or the 5xx (Permanent Negative) category is that replies are 4xx if the commands can be repeated without any change in command form or in properties of the User or Server (e.g., the com
Free SFTP, SCP and FTP client for Windows News Introduction SSH Client SFTP Client FTP Client Download Install Donate Documentation Guides F.A.Q. Scripting .NET & COM Library Screenshots Translations Support Forum Tracker History [[sftp_codes]] WinSCP Contents » Getting Started » Protocols » SFTP
Ftp Error 500
» SFTP Status/Error Codes SFTP status/error codes are a numerical codes that an SFTP ftp error 421 server1) uses to indicate a result of a client request (i.e. a request sent by WinSCP to the server). WinSCP
Ftp Error 421 Service Not Available
translates the numerical codes to a textual description for you, so you do not have to remember them. The SFTP server should also provide a meaningful textual description of the error itself. WinSCP includes the https://en.wikipedia.org/wiki/List_of_FTP_server_return_codes server-side description in its error message, labeled "Error message from server". Such description can include more detailed information than WinSCP can possibly deduce from the numerical code. Code 4 (Failure) Codes List References Code 4 (Failure) Note that not all servers use all codes. Most SSH/SFTP servers, including the most commonly used OpenSSH, support only SFTP version 3 that defines only codes 0 to 8. Advertisements: These servers would https://winscp.net/eng/docs/sftp_codes generally use code 4 (Failure) for many errors for which there is a specific code defined in the later versions of SFTP protocol, such as: Renaming a file to a name of already existing file. Creating a directory that already exists. Moving a remote file to a different filesystem (HDD). Uploading a file to a full filesystem (HDD). Exceeding a user disk quota. In this case the server is required to provide meaningful description of the error itself (see above). Unfortunately, OpenSSH SFTP server uses always description "Failure". Is such case, there is unfortunately no way to tell a reason of the failure. Codes List Code Name Description Comment 0 OK Indicates successful completion of the operation. 1 EOF An attempt to read past the end-of-file was made; or, there are no more directory entries to return. 2 No such file A reference was made to a file which does not exist. 3 Permission denied The user does not have sufficient permissions to perform the operation. 4 Failure An error occurred, but no specific error code exists to describe the failure. This error message should always have meaningful text in the the error message field. See above. 5 Bad message A badly formatted packet
error Type of Internet access set to “None”.A DNS server must be entered. There is no connection to the network. Set correct access type.Enter correct DNS. Check cables and plugs.102 Cannot open socket. Internal error Prepare configurationand data back up and contact Support.103 Cannot connect socket The connection is disrupted by a firewall.The server is overloaded. Set appropriate approvals in the firewall. Try again later.104 No answer from the server. There is a fault on the FTP server.Try again later. Restart the FTP server.105 Wrong response from the server. The FTP server used is not supported or is notconfigured correctly. Use another FTP server or check the configuration.106 User/password incorrect. The user name of password to access the FTP was entered incorrectly.Check spelling.107 Wrong directory. An incorrect directory was set for the transmission. Check spelling.Errors when transferring the back up:108 Unable to send the file.Errors when transferring data without losing the test connection.111 Error in remote file name. This is an internal error. Contact support.112 Error when setting the representation type. The FTP server used is not supported or notconfigured properly. Use another FTP server or check the configuration.113 Error when setting the passive mode. The FTP server used is not supported or notconfigured properly. The connection is disrupted by a firewall.The Internet connection has been disrupted. Use another FTP server or check the configuration.Set appropriate approvals in the firewall. Check the Internet connection.114 Socket could not be opened. Internal error Prepare configuration and data back up and contact Support.115 IP address could not be changed. Internal error Contact support.116 Socket could not be connected. The connection is disrupted by a firewall.The server is overloaded. Set appropriate approvals in the firewall. Try again later.117 Unknown error118 STOR failed. There is a fault on the FTP server. Try again later. Restart the server.Check free memory space on the server.119 File could not be opened. Internal error. Contact support.120 Time exceeded, no answer The server is overloaded. The connection is disrupted by a firewall.Try again later. Set appropriate approvals in the firewall.121 Time exceeded, transmission error. The server is overloaded. The Internet connection has been disrupted. Try again later. Check the Internet connection.122