Ftp Put Error Codes
Contents |
good, bad or incomplete: Range Purpose 1xx Positive Preliminary reply The requested action is being initiated; expect another reply before proceeding with a new command. (The user-process sending another command before the completion reply would be in violation
Ftp Code 226
of protocol; but server-FTP processes should queue any commands that arrive while a preceding command sftp return codes is in progress.) This type of reply can be used to indicate that the command was accepted and the user-process may now ftp error 426 pay attention to the data connections, for implementations where simultaneous monitoring is difficult. The server-FTP process may send at most, one 1xx reply per command. 2xx Positive Completion reply The requested action has been successfully completed. A
Ftp Return Codes Mainframe
new request may be initiated. 3xx Positive Intermediate reply The command has been accepted, but the requested action is being held in abeyance, pending receipt of further information. The user should send another command specifying this information. This reply is used in command sequence groups. 4xx Transient Negative Completion reply The command was not accepted and the requested action did not take place, but the error condition is temporary and the action may be requested
Ftp Error 421 Service Not Available
again. The user should return to the beginning of the command sequence, if any. It is difficult to assign a meaning to "transient", particularly when two distinct sites (Server- and User-processes) have to agree on the interpretation. Each reply in the 4xx category might have a slightly different time value, but the intent is that the user-process is encouraged to try again. A rule of thumb in determining if a reply fits into the 4xx or the 5xx (Permanent Negative) category is that replies are 4xx if the commands can be repeated without any change in command form or in properties of the User or Server (e.g., the command is spelled the same with the same arguments used; the user does not change his file access or user name; the server does not put up a new implementation.) 5xx Permanent Negative Completion reply The command was not accepted and the requested action did not take place. The User-process is discouraged from repeating the exact request (in the same sequence). Even some "permanent" error conditions can be corrected, so the human user may want to direct his User-process to reinitiate the command sequence by direct action at some point in the future (e.g., after the spelling has been changed, or the user has altered his directory status.) 6xx Protected reply The RFC 2228 introduce
Free SFTP, SCP and FTP client for Windows News Introduction SSH Client SFTP Client FTP Client Download Install Donate Documentation Guides F.A.Q. Scripting .NET & COM Library Screenshots Translations Support Forum Tracker History [[sftp_codes]] WinSCP Contents » Getting Started » Protocols ftp error 500 » SFTP » SFTP Status/Error Codes SFTP status/error codes are a numerical codes
Ftp Command Codes
that an SFTP server1) uses to indicate a result of a client request (i.e. a request sent by WinSCP to the ftp response 421 received. server closed connection. server). WinSCP translates the numerical codes to a textual description for you, so you do not have to remember them. The SFTP server should also provide a meaningful textual description of the error https://en.wikipedia.org/wiki/List_of_FTP_server_return_codes itself. WinSCP includes the server-side description in its error message, labeled "Error message from server". Such description can include more detailed information than WinSCP can possibly deduce from the numerical code. Code 4 (Failure) Codes List References Code 4 (Failure) Note that not all servers use all codes. Most SSH/SFTP servers, including the most commonly used OpenSSH, support only SFTP version 3 that defines only codes 0 https://winscp.net/eng/docs/sftp_codes to 8. Advertisements: These servers would generally use code 4 (Failure) for many errors for which there is a specific code defined in the later versions of SFTP protocol, such as: Renaming a file to a name of already existing file. Creating a directory that already exists. Moving a remote file to a different filesystem (HDD). Uploading a file to a full filesystem (HDD). Exceeding a user disk quota. In this case the server is required to provide meaningful description of the error itself (see above). Unfortunately, OpenSSH SFTP server uses always description "Failure". Is such case, there is unfortunately no way to tell a reason of the failure. Codes List Code Name Description Comment 0 OK Indicates successful completion of the operation. 1 EOF An attempt to read past the end-of-file was made; or, there are no more directory entries to return. 2 No such file A reference was made to a file which does not exist. 3 Permission denied The user does not have sufficient permissions to perform the operation. 4 Failure An error occurred, but no specific error code exists to describe the failure. This error message should always have meaningful text in the the error me