Ftp Put Error F
Contents |
good, bad or incomplete: Range Purpose 1xx Positive Preliminary reply The requested action is being initiated; expect another reply before proceeding with a new command. (The user-process sending another command before the completion reply would be in violation of protocol; but ftp error codes server-FTP processes should queue any commands that arrive while a preceding command is in progress.) This ftp error 426 type of reply can be used to indicate that the command was accepted and the user-process may now pay attention to the data ftp return codes mainframe connections, for implementations where simultaneous monitoring is difficult. The server-FTP process may send at most, one 1xx reply per command. 2xx Positive Completion reply The requested action has been successfully completed. A new request may be initiated. 3xx Positive ftp error 421 service not available Intermediate reply The command has been accepted, but the requested action is being held in abeyance, pending receipt of further information. The user should send another command specifying this information. This reply is used in command sequence groups. 4xx Transient Negative Completion reply The command was not accepted and the requested action did not take place, but the error condition is temporary and the action may be requested again. The user should return to the beginning of the command
Ftp Error 500
sequence, if any. It is difficult to assign a meaning to "transient", particularly when two distinct sites (Server- and User-processes) have to agree on the interpretation. Each reply in the 4xx category might have a slightly different time value, but the intent is that the user-process is encouraged to try again. A rule of thumb in determining if a reply fits into the 4xx or the 5xx (Permanent Negative) category is that replies are 4xx if the commands can be repeated without any change in command form or in properties of the User or Server (e.g., the command is spelled the same with the same arguments used; the user does not change his file access or user name; the server does not put up a new implementation.) 5xx Permanent Negative Completion reply The command was not accepted and the requested action did not take place. The User-process is discouraged from repeating the exact request (in the same sequence). Even some "permanent" error conditions can be corrected, so the human user may want to direct his User-process to reinitiate the command sequence by direct action at some point in the future (e.g., after the spelling has been changed, or the user has altered his directory status.) 6xx Protected reply The RFC 2228 introduced the concept of protected replies to increase security over the FTP communications. The 6xx replies are Base64 encoded protected messages tha
» FTP Status and Error Codes FTP Status and Error Codes Last Year GlobalSCAPE 5 CuteFTP for Windows THE INFORMATION IN THIS ARTICLE APPLIES TO: EFT Server all versions CuteFTP® all versions DISCUSSION During FTP sessions, servers send and receive various numbered codes to/from FTP clients.
Sftp Error Codes
Some codes represent errors, most others simply communicate the status of the connection. Below ftp 530 are brief explanations for the most common status and error codes. When determining a course of action, review the entire log; ftp response 421 received. server closed connection. some codes are informational only, others indicate that you have entered the wrong information, and others indicate what the information is that you need to provide before continuing. For troubleshooting CuteFTP connection problems, also refer https://en.wikipedia.org/wiki/List_of_FTP_server_return_codes to Troubleshooting CuteFTP Connection Problems. The table below is provided so that you have some idea whether you can solve the issue on your own (e.g., code 331=you need to provide a password) or you need to call your ISP for assistance (e.g., code 426=you are unable to connect to the remote server). These codes are used by most FTP servers/clients. NOTE: The information below is only offered as a courtesy https://kb.globalscape.com/KnowledgebaseArticle10142.aspx to assist you in telling your Internet Service Provider what the error is so that they can help solve your issue. For example, if you get a code 426, the transfer was aborted and the connection closed. The solution to this error is to "try logging back in; contact your hosting provider to check if you need to increase your hosting account; try disabling the firewall on your PC to see if that solves the problem. If not, contact your hosting provider or ISP." The list below contains standard FTP codes. Numbers outside this list are proprietary to the Server or Client that you are using. Code Description Discussion 100 Series The requested action was initiated; expect another reply before proceeding with a new command. 110 Restart marker reply. The text is exact and not left to the particular implementation; it must read "MARK yyyy = mmmm" where yyyy is User-process data stream marker, and mmmm server's equivalent marker (note the spaces between markers and "="). 120 Service ready in nn minutes. (Informational) 125 Data Connection already open; transfer starting. (Informational) 150 File status okay; about to open data connection. FTP uses two ports: 21 for sending commands, and 20 for sending data. A status code of 150 indicates tha
Tutorials Poetry RecentThreads NewestNodes Donate What'sNew on Aug 14, 2002 at 10:10UTC ( #190020=perltutorial: print w/replies, xml ) Need Help?? Preamble I have to deal with FTP a lot... uploading and getting files, mostly from the same http://www.perlmonks.org/?node_id=190020 server & directory (where files we give to customers reside). Well, I decided to try and automate things a bit, and use Perl for this purpose. use Net::FTP I immediately plunged into CPAN and found this nice module, that seemed to be just what I needed. However, trying to find a good tutorial on the subject (the docs of this module are ftp error quite good, but with a tutorial it is possible to get started quicker), I was dissapointed and decided to write one, on a very basic level, for other monks. Let's go ... First, connecting and logging to the desired server. As I said earlier, most of the time I just need one server with one user name (and most of these times, ftp error codes the same directory), so I just store them in variables. use strict; # Don't forget ! use Net::FTP; my $host = "your.favorite.server"; my $user = "user"; my $password = "password"; my $f = Net::FTP->new($host) or die "Can't open $host\n"; $f->login($user, $password) or die "Can't log $user in\n"; [download] As simple as that... neat, huh ? Well, now that we're in, all sorts of things possible with FTP can be done. For example, getting into a directory: my $dir = "my/favorite/dir"; $f->cwd($dir) or die "Can't cwd to $dir\n"; [download] The most basic and useful operations are getting and putting files to/from the server. This is done with the get() and put() methods, and w/o any special options the files must reside in the directory from which your script was called. Here is the usage: my $file_to_get = "something"; my $file_to_put = "other something"; $f->get($file_to_get) or die "Can't get $file from $dir\n"; $f->put($file_to_put) or die "Can't put $file into $dir\n"; [download] These operations will usually do for 95% of your FTP'ing, but there are more interesting things to do, and this is where Perl comes into q