Canon Pixma Ix4000 Operator Error
Contents |
by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer canon pixma ix4000 driver you receive. Ask Sandeep Pamarati Your Own Question Sandeep Pamarati, Engineer Category: Printers Satisfied Customers: canon pixma ix4000 handbuch 1660 Experience: Bachelors in Electronics and Proficient in troubleshooting Computer and Printer-related problems 383181 Type Your Printers Question Here... Sandeep Pamarati is canon pixma ix4000 treiber online now My canon pixma ip4000 gets an operator error. For solution Resolved Question: My canon pixma ip4000 gets an "operator error." For solution it says to press resume button and if this doesn't work to canon pixma ix4000 prix turn the computer off and on again. have done this several times with no results (keeps flashing orange). Please advise how to correct this error. Submitted: 5 years ago. Category:Printers Share this conversation Expert: Sandeep Pamarati replied5 years ago. Sandeep Pamarati : Hai Sir,Sandeep Pamarati : Happy to help you....Sandeep Pamarati : in this case you need to reset the printer.....Sandeep Pamarati : Resetting the PrinterBy resetting the printer's power, the print
Canon Pixma Ix4000 Review
buffer is cleared and certain sensors are reset. If there is invalid data in the buffer, or sensors are stuck in a particular mode; errors may occur.Follow these steps to reset the printer:Turn the printer off with the Power button (if available).Disconnect the data cable from the printer (not applicable to WiFi, Bluetooth or Infrared) .Unplug the printer's power cord for approximately 10 minutes, and then plug it back in. If troubleshooting a communication issue, reconnect the data cable (not applicable to WiFi, Bluetooth or Infrared).Turn the printer back on.Note: If resetting the printer does not work, please attempt any other solutions that appeared in your search results.If this is a hardware error on the printer, the printer may need to be repaired.Sandeep Pamarati : Try to do and let me know the situation sir...Sandeep Pamarati : I will wait for your reply.....Sandeep Pamarati : Thanks for your time...Sandeep Pamarati : Good Day to you....JACUSTOMER-u4c4mcws- : Followed your instructions but, alas, it didn't work. Even left the cord unplugged for 30 minutes. Any other suggestions? Sandeep Pamarati : Let me know did you find the error code.....?>Sandeep Pamarati : You said onrange light is flashingSandeep Pamarati : How many times it is flashing....?JACUSTOMER-u4c4mcws- : orange light flashes 5 times, turns green, then flashes 5 times, etc.Sandeep
TechSpot RSS Get our weekly newsletter Search TechSpot Trending Hardware The Web Culture Mobile Gaming Apple Microsoft Google Reviews Graphics Laptops Smartphones CPUs Storage Cases
Canon Pixma Ix4000 Prezzo
Keyboard & Mice Outstanding Features Must Reads Hardware Software Gaming Tips & canon pixma ix4000 druckkopf Tricks Best Of Downloads Latest Downloads Popular Apps Editors Picks Device Drivers Product Finder New Releases New PC Games canon pixma ix 4000 Laptops Smartphones Routers Storage Motherboards Monitors Forums Recent Activity Today's Posts News Comments TechSpot Forums Forums TechSpot Core Build a PC Today's Posts Canon ip4000 print headissue Byianpmonaro Jan 28, 2010 1st http://www.justanswer.com/printers/4egji-canon-pixma-ip4000-gets-operator-error-solution.html time user, so go easy ... have an old but up until now trust worthy canon ip4000 printer with a printhead error (5 orange flashes). have searched and followed directions on cleaning printhead ... all went well except as soon as the printhead was repositioned and the machine was switched back on I now have a situation where it goes straight to 5 orange http://www.techspot.com/community/topics/canon-ip4000-print-head-issue.142052/ flashes. Cant do any print maintanence as I get this message ... "Operator error. Press printer's RESUME button. If this doesn't clear the error, cancel printing and turn the printer off and then back on." No error codes just this and 5 orange flashes. HELP Jan 28, 2010 #1 Archean TechSpot Paladin Posts: 5,680 +85 As you say it flashes orange light five times consecutively, that means there is a print head error. Reset the print head, then reset the printer. To reset the print head, make sure the printer is on. Open the paper output tray and top cover. Make sure the print head holder is in the center and open the inner cover. remove all the ink tanks. Raise the print head lock lever and remove the print head. Reset the print head and lock the lever. Replace the ink tanks. Jan 28, 2010 #2 ianpmonaro TS Rookie Topic Starter Thanks, have tried that a number of times including cleaning all contacts... stilll 5 orange flashes. Jan 28, 2010 #3 Archean TechSpot Paladin Posts: 5,680 +85 Well then it probably is a
resealed and replaced. Now I have these red lights blinking at me. What to do????I have had a Canon http://www.fixyourownprinter.com/posts/59011 i865 for over 4 years which I have been doing the same as above without a single problem. I note in another forum :- http://www.fixyourownprinter.com/forums/inkjet/41348that people are having problems with their Canon Pixma IP1000 Waste Ink Full warning lights, and I was wondering if the same method would fix this problem???In anticipation,Ashflat. Respond to this 0 Maybe this link will help you http://slayo.com/service-mode-canon-pixma-ix5000-ix4000-printers.html canon pixma by scmedan on Nov 2, 2008 at 8:22pm Add comment Please sign in to comment 0 To reset counter Canon PIXMA iX4000 or iX5000 you have to enter to service mode. Procedure to enter to service mode on Canon PIXMA iX4000 or iX5000 is as following :1.Connect the Canon PIXMA iX5000 or iX4000 printer to the power cord. ( note : If the canon pixma ix automatic power-on function is enabled in the printer, the printer enters the service mode for the first time, but it will never enter the service mode if the printer is turned off by the Power button. This is because the printer remains to be turned on internally if the power is turned off by the Power button. To prevent this, disconnection of the power cord is required before starting the printer in the service mode ) .2.With the Canon PIXMA iX5000 or iX4000 printer powered off, while pressing the Resume/Cancel button, press and hold the Power button. (note : Don¡¯t release the buttons. The Power LED lights in green to indicate that a function is selectable.)3.While holding the Power button, release Resume/Cancel button. (Don¡¯t release the Power button.)4.While holding the Power button, press Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons.5.When the Power LED lights in green, press the Resume/Cancel button 4 times to reset waste ink counter in the Canon Pixma iX5000 / iX4000. (note : If the Power LED does not light in green the printer does not enter the ser