Canon Pixma Mp450 Printer Error Code 6500
Contents |
by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee
Canon Pixma Mp450 Printer Driver For Mac
Rate the answer you receive. Ask bineesh Your Own Question bineesh, Computer Support canon pixma mp450 error code 5100 Specialist Category: Computer Satisfied Customers: 767 Experience: MCSE and MCP Certified Engineer 27375559 Type Your Computer Question Here... bineesh is online
Canon Pixma Mp450 Software
now Canon Pixma MP450 printer shows error code 6500. What causes Customer Question Canon Pixma MP450 printer shows error code 6500. What causes this and how do I fix it? Submitted: 6 years canon pixma mp450 ink ago. Category:Computer Share this conversation Expert: bineesh replied6 years ago. HelloThanks for using Just Answer.The 6500 error code is a logic board error code. The PCI Bus error is detected by the ASCI. Sounds like it needs new logic board. but i suggest you to first of all you can try to reset your printer -1. Turn the printer off with the Power button (if available).2. Disconnect the canon pixma mp450 manual data cable from the printer.3. Unplug the printer's power cord for approximately 10 minutes, and then plug it back in. 4. Turn the printer back on. If this works you're done, if not try the next step.1. After confirming that the printer is powered on, open the paper output tray.2. Open the top cover and wait until the print head moves to the center.3. Open the inner cover and check that ink tanks are properly seated.4. Properly seated5. Press down on each ink tank until a click is heard.6. Close the inner cover and top coverif reset method not works for you then you go for the new logic board replacement .............Good Luck!!Let me know is this information helpful for you.. Ask Your Own Computer Question Share this conversation JustAnswer in the News: Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com. JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance. Web sites like justanswer.com/legal...leave nothing to chance. Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days.
resolve this problem.Many ThanksRachael Respond to this 1 1. Turn off printer.2. retaining button Stop/Reset (red triangle in the circle) press button POWER
Canon Pixma Mp450 How To Scan
- indicator it will light up with green color.3. let go button Stop/Reset, continuing canon pixma mp450 scanner driver to hold POWER.4. press button Stop/Reset 2 times, while holding POWER button, after which you will let go all buttons.5.
Canon Pixma Mp450 Won't Scan
when indicator is lit BY Solid GREEN - press Stop/Reset 4 times! (this is the key)6.turn off printer by POWER button, then turn on. 7. You should be set. If it didn't work, http://www.justanswer.com/computer/3jmue-canon-pixma-mp450-printer-shows-error-code-6500-causes.html try it again, slowly. It WILL work!still not working... when i turn it on, error 6500 error code appears... by tyroneboogieman on Aug 8, 2009 at 6:54am Add comment Please sign in to comment 0 I have found it. Here's the answer for everyone else who needs it.Canon Waste Ink Tank Reset ProceduresCanon GENERIC "S" SERIES RESET CODEWaste Ink Counter Reset.(1) Turn off the printer.(2) Press http://www.fixyourownprinter.com/posts/52461 and hold the RESUME button, then press and hold the POWER button.(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in succession. Note: you are still holding the POWER button). The printer's carriage will "reset" or move momentarily. If the above was properly performed the printer will enter the "Service Mode".(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press. 1. Service/Factory test printout, including ink sensor check. 2. EEPROM - Info printout. 3. EEPROM - Initialization. 4. Reset the Waste ink counter. 5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.++++++++++Canon i320, i255Waste Ink Counter Reset.Step 1 : Manual for service mode1. Unplug power and USB.2. Open door and hold power button.3. Connect power.4. Close door, then release power button.or Step 1: Manual for service mode1. Turn off the
HomeForumPrinters & CopiersCanonPIXMAPixma MP450 All-In-One InkJet PrinterMy new canon pixma... Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about Canon Pixma MP450 All-In-One InkJet Printer 1 http://www.fixya.com/support/t4326736-new_canon_pixma_mp450_error_code_6500 Answer My new canon pixma MP450 has an error code of 6500 on the display panel. Can you please tell me how to fix it Posted by robynsmart1 on Mar 13, 2010 Want Answer 0 Clicking this will make more experts see the question and we will remind you when it gets answered. Comment Flag More Print this page Share this page × Moderate Help this question get an answer Is canon pixma this question mis-categorized or about a different product? Help this question get an answer by entering the correct category or product below. Did you mean? Yes No Cancel Update (+2 points) You can't post conmments that contain an email address. × Comment Anonymously Video Images 1 Answer mukhtar21 shaikh Level 3: An expert who has achieved level 3 by getting 1000 points All-Star: An expert that got 10 achievements. MVP: An expert that canon pixma mp450 got 5 achievements. President: An expert whose answer got voted for 500 times. Canon Master 2,015 Answers Re: My new canon pixma MP450 has an error code of 6500 on... This is printer logic motherboard problemThe 6500 error code is a logic board error code. The PCI Bus error is detected by the ASCI. Sounds like it needs new logic board. but i suggest you to first of all you can try to reset your printer -1. Turn the printer off with the Power button (if available).2. Disconnect the data cable from the printer.3. Unplug the printer's power cord for approximately 10 minutes, and then plug it back in. 4. Turn the printer back on. If this works you're done, if not try the next step.1. After confirming that the printer is powered on, open the paper output tray.2. Open the top cover and wait until the print head moves to the center.3. Open the inner cover and check that ink tanks are properly seated.4. Properly seated5. Press down on each ink tank until a click is heard.6. Close the inner cover and top coverif reset method not works for you then you go for the new logic board replacement . Hope this helps. Please rate my response.Thanks.Have a good day. Posted on