Hp 2200 Printer Error
Contents |
on the printer. I checked and there is no paper jam, nor is there any tray open, and the caterlage is there. Please what should I do? Thanks. Respond to this 2 It is not as simple as most printers.Turn the printer of and remove the paper tray.Lay it hp laserjet 2200 orange light flashing on it's right side.The are to clips/collars on either side of the roller.Rotate them 1/4 turn towards the
Hp Laserjet 2200 Service Manual
bottom of the printer and one will slide out of the printer and the other up the shaft.DO NOT LET THE MAIN SHAFT MOVE TOO MUCH OR IT hp laserjet 2200d all three lights on MAY BECOME DISCONNECTED FROM THE MAIN DRIVE (BAD DESIGN).THE REPLACEMENT ROLLER WILL ONLY FIT IN ONE WAY - THE SLOTS ARE DIFFERENT DEPTHS. by mcprinter on Aug 10, 2006 at 4:40pm Add comment Please sign in to comment 2 Looks like the memory on the formatter hp laserjet 2200 secondary light pattern is bad. Reason is the middle green light is the data received light and always lights as the printer is receiving data or will stay on solid if data is in the buffer and something is preventing it from printing. One thing you can try is a NVRAM reset which may or may not work. Turn off the power. Now hold down the go button (big button in front) and turn the power on and hold the button down until all three lights come on solid. Release the button and the printer should
Hp Laserjet 2200 Troubleshooting
then start cycling the lights until it comes to ready. At this point I would try the test page again and this time make sure the cable from the computer is NOT connected. If you get the same reaction, then the formatter is toast and needs to be replaced. If you now get a good test page, turn off the printer, reattach the computer cable, turn back on and try again. by dmzcompute on Dec 20, 2006 at 3:34pm Add comment Please sign in to comment This took care of two of my printers. The feeding 1/4 inch at a time seems to be a cleaning sheet of som e kind. I get this sheet by holding the go button for 15 seconds and then releasing. Once I did the reset on the third 2200 and tried to print a test page using the go button I get a medium pitch humming noise, that I would describe as rubber moving against something that is not moving. All three lights come on solid at this point when I hold job cancel and go the go light turns off and the attention and ready lights stay on solid.I did some searching around and was not able to find this light pattern on this site or on HP. If you could point me in the right direction on this issue I would appreciate it. - slaglema 1 The printer initialise ok then when you try to print test page the gears turns but it fails to pick the paper the paper pick gears are not turning. by unknown on Jul 18, 2005 at 6:07am Add comment Please sign i
the control panel simulator. There are two methods for accessing the control panel simulator. After software installation If the control panel simulator was installed during the printer software installation, select Start, Programs, HP LaserJet http://www.advancedlaser-hp-error-codes.com/error2200.htm 2200, and then Control Panel Simulator. From the software CD-ROM Insert the CD into the PC CD-ROM drive. Select Start, then Run. Click Browse. Locate and double-click X:\English\docs\cpemulator.exe (where X:\ refers to the drive letter for the CD-ROM drive). Figure 1: Control panel buttons 1- JOB CANCEL button 2- Attention light (red) 3- Ready light (green) 4- GO light (green) and button Button usage The printer has two buttons: JOB CANCEL and hp laserjet GO. Job cancel Press JOB CANCEL to cancel a job the printer is currently printing. The control panel lights will cycle while the print job is cleared from both the printer and the computer, and then return to the Ready state (Ready light on). This may take some time, depending on the size of the print job. If JOB CANCEL is accidentally pushed, the job must be reprinted. There is no undo hp laserjet 2200 function. If JOB CANCEL is pushed when the printer is idle, the top panel status lights will cycle, but nothing else will happen. Go Press GO to resume printing when the printer is paused or when unprinted data is still in the printer. Press GO to clear some printer errors. Press GO to print a demo page. The printer must be in the Ready state (Ready light on). Troubleshooting control panel messages Printer status is indicated by light patterns on the control panel. The lights can be in any one of the following states: Figure 2: Three states of the Power light 1- Off 2- On 3- Blinking Basic control panel messages The following control panel messages indicate various conditions of the printer in preparation for, or during printing. Type of error Light pattern Recommended action Startup The Go (green), Ready (green), and Attention (red) lights cycle one after another. The buttons have no effect until the printer is ready. Ready The Ready (green) light is on and the printer is ready to print. The Ready light is solid. No action is needed. Pressing GO will print a demo page. Processing The printer is receiving or processing data when the Ready (green) light is blinking. Pressing JOB CANCEL cancels the current job. One or