Hp Laserjet 1320tn Error
Contents |
be down. Please try the request again. Your cache administrator is webmaster. Generated Mon, 17 Oct 2016 23:13:13 GMT by s_wx1131 (squid/3.5.20)
17 18 Next > < Back = Page 19 = 19
Hp Laserjet 1320 Troubleshooting
20 21 22 23 24 25 26 27 28 Page hp laserjet 1320 lights indicators format is different than on another printerIf you used an older or different printer driver (printer hp laserjet 1320 printing blank pages software) to create the document or the printer Properties settings in the software are different, the page format might change when you try to print using http://answers.microsoft.com/en-us/windows/forum/windows_vista-hardware/hp-laserjet-1320-flashing-orange-light-fails-to/7b18b75b-6675-e011-8dfc-68b599b31bf5 your new printer driver or settings. To help eliminate this problem, try the following:●Create documents and print them using the same printer driver (printer software) and printer Properties settings regardless of which HP LaserJet printer you use to print them.●Change the resolution, paper size, font settings, and other settings. See Advanced Printer http://manualmachine.com/hp/laserjet-1160-1320/195366-service-manual/page:19/ Settings window for more information.Graphics qualityThe graphics settings might be unsuitable for your print job. Check the graphic settings, such as resolution, in the printer Properties and adjust them as necessary.NOTESome resolution might be lost when converting from one graphics format to another. ENWWPrinted page is different than what appeared on screen 149 Status light patternsTable 7-3.Light status legendSymbol for "light off"Symbol for "light on"Symbol for "light blinking" Table 7-4.Control panel light messageLight statusState of the printer Initialization/StartupWhile in the Startup state, the Go, Ready, and Attention lights cycle (at the rate of 500 ms) one after another. ActionDuring the Initialization process, pressing buttons has no effect. 150 Chapter 7 TroubleshootingENWW Table 7-4.Control panel light message (continued)Light statusState of the printer Reconfiguration InitializationDuring the printer start up, you can request special initialization sequences that reconfigure the printer. When one of the sequences is requested, such as a cold reset, the lights cycle as in the Initialization/Startup state
jobs but upon testing it really doesn't seem to matter. Text, Acrobat, Graphics sometimes they'll print sometimes then end with a fatal error. Here are the symptoms:I send the job http://fixyourownprinter.com/posts/47306 to the printer via a Jetdirect 300x (external through parallel cable to printer)The job light blinks on the printer.The printer starts the print process. (rollers etc)I hear what seems to be the paper pickup process. (clicking)Right after the above step I get the fatal error lights, hitting Go to check secondary does nothing as the fatal error indicators stay lit.The only thing left to do is to reset the printer and more often than not the hp laserjet error just repeats itself. I have checked the pickup roller and the paper path sensors that I can see, there are no issues with them.Any tips on what to check next? Respond to this 0 Disconnect the parallel cable.Power cycle the printer, (leave it off for at least 5 seconds before you turn it back on).Push and release the Go button, a demo page should print.If the demo page does not print then the Go button might hp laserjet 1320 not be working.If you get a fatal error when printing the demo page, then press and hold the Go button, what is the secondary pattern? (flashing or solid)If the demo page works then print the config page, start with the printer in ready status, press and hold Go till the yellow light comes on, release Go. (A supplies status page should also print)The config page will list the last few event log entries, please post them.If the config page works, then test the printer by attaching the parallel cable to a PC, or use a USB cable. by Stephen on May 1, 2007 at 12:12pm Add comment Please sign in to comment 0 Hmm....This is a strange one, looks like a defective toner. I just happened to have a new toner sitting here and replaced the installed one with the new one to run the demo page (I've done it before and it's random whether or not it worked, same result with the engine test as I have the side covers off).The printer has now printed everything I have thrown at it for the past 30min. I can't see anything wrong with the old toner, the contacts have wear spots from contact with the printer so I know that's ok. I can move the drum with my fingers on the gear, it's a relatively new genuine t