Hp Laserjet 2420 Error 13.01.00
LATE JAM" I have tried changing the paper, toner cartridge, and paper tray with one from another unit. I have verified that the paper size is set correctly on the tray. The paper feeds normally form tray 1 (the manual feed). I cannot find any scraps of paper in the paper path or anything else that looks ouut of the ordinary. This printer is only 4 months old and still under warranty. I can send it in to HP for service, but would like to know if there is anything I can do or check before I go that route.THanks in advance. Respond to this 0 Turn the printer around and lift the flap behind the paper tray. If you have a flashlight, get it. You want to watch the action of the paper pickup roller. By observing to see if it is rotating, slipping on the paper or whatever, you should be able to determine why the paper isn't feeding. A lot of times, it is as simple as the paper backstop has slid back and the roller can't grab the paper that is 2 inches out of reach. Wish I had $10 for every one of those I've seen. Since you've replaced the tray and paper, I would think you might have noticed that. Is the paper moving out of the tray at all? by moe on Jul 23, 2007 at 5:26pm Add comment Please sign in to comment Thanks moe for the super quick response. I will look from the rear tomorrow at the pickup rollers.When I was first called to look at the problem, my first discovery was that the paper backstop had slid back. I fixed it but the problem kept occurring. The paper picks up and feeds for about 3 inches before it stops and reports the jam. The paper feed is a bit uneven. Goes in a bit more on the left than the right. As I said in the previous post, swapping with another tray did not help at all. Thanks again for any help you can offer. I'll let you know what I find out tomorrow when I take a peek from the rear. - amifiles 0 Go to the link below if Moe's suggestion does not work. Lot faster then sending to hp.http://hp.infonow.net/bin/findNow?CLIENT_ID=HP_LOC_USA_SRV by dmzcompute on Jul 23, 2007 at 5:52pm Add comment Please sign in to comment 0 Sounds like you may have a small shred of paper stuck in the paper path. Sometimes using a stiff folder feeding up from the bottom with the tray removed will dislodge it. by dmzcompute on Jul 23,
2420 paper jam error 13.01.00 > Hp laserjet 2420 paper jam error 13.01.00 Discussion in 'Technical Writer' started by BlackSEO, 24-Aug-2016. w210 XenForo Moderator When printing from tray 2, I am getting the jam error code No jams are in the machine the paper never leaves the cassette. Check it for the red dust of doom, it means the metal parts inside the clutch are worn out and the clutch needs to be replaced. I can print a few pages and then I receive the jam http://www.fixyourownprinter.com/posts/49328 code. Pushing a piece of thick paper through the paper feed area to remove any debris. This machine has 2 additional cassettes added onto it. Also, make sure that the solenoid that controls that clutch is in good shape. I used a small felt that I had in my tool bag Sent from my SM-G920T using Tapatalk I have a length of inner tube. http://asantechildrenstheatre.org/essayforums/Technical+Writer/hp-laserjet-2420-paper-jam-error-1301000550f6d7967f9dc0bca2b945e0a91891.html I use a 1/4" paper punch to punch 1/4" disks of rubber. Essays italics quotes Consider the lobster and other essays analysis Personal statement examples children's nursing HP LaserJet 4250tn Jam in Tray 2 error code Forum, Laser Printer Service Help and Techncial Support An essay on bargaining DriverRestore.com/Pilotes-HP HP LaserJet 2420d, 2420dn printer repair HP 2420/2420n service. HP 4250 means page is jammed near the output door, error message indicates paper jammed in the rear door and indicates that there is a paper jam in the staple cartridge. I replaced the fuser and did a full maintenance kit, I was getting the paper jam error on all trays except for the manual tray. HP laserjet 4200/4300/4250 printer repair with paper jam error. LaserJet printer repair with paper jam error. HP 2420/2420n service ; HP LaserJet. Huh, maybe I'm thinking of the wrong machine (if so, let me know please), but when I've seen that solenoid stick it usually causes almost the exact opposite problem - too many sheets of paper get fed because the rollers never stop. I have tried the following: 2 sets of brand new feed rollers for
pm 0 Rating/ Voters Page is jammed in tray X. 13.01.00 error message indicates that the media did not arrive at the pre-feed sensor ( PS 102 ) within the specified time. 13.03.00 error message indicates that the http://www.laserprinterhelp.net/article/AA-00540/0/13.01.00-or-13.03.00-Jam-in-Tray-X-or-13.03-Paper-JamOpen-input-TraysThen-Open-and-Close-Top-Cover.html media did not arrive at the top-of -page sensor ( PS 103 ) within the specified time. NOTE: The 13.01.00 error can also be caused by the failure of the paper-level sensor (PS107). If this sensor fails,the http://superuser.com/questions/947670/motor-not-working-on-hp-laserjet-2300-error-13-01-00 lifter motor does not rotate to lift the paper tray plate. This error can also be caused when the printer attempts to pickup media from a tray that is EMPTY,but the paper-out sensing mechanism for that tray hp laserjet has failed and the printer senses that the tray appears to be loaded.1. Press the HELP button for detailed information about clearing the jam. Press the UP ARROW button and the DOWN ARROW button to step through the instructions.2. Check that the paper-out sensor in the specified tray is functioning properly.3. Clean the pickup, feed and separation rollers. If they are worn or damaged replace them ALL.4. Verify that the pre-feed sensor (PS102) is hp laserjet 2420 installed correctly.5. Open and close the specified tray while watching the control-panel display. A short delay should occur between when the tray closes and the tray-size message appears on the control panel display. If there is no delay and you do not hear the tray-lift motor lift the tray plate into place,replace the tray stack position sensor.6. Replace the trays pickup solenoid.7. Replace the trays paper pick up assy8. Verify that the top-of page sensor is operating correctly and that the sensor flag can move freely. replace the sensor if it is not operating correctly.9. Replace the DC controller PCA. Related Articles 9000/9050/9050MFP Maintenance Kit 13.01.00 or 13.03.00 Jam in Tray X or 13.03 Paper Jam,Open input Trays,Then Open and Close Top Cover 13.XX.YY jam in tray2 13.XX.YY jam in tray X Clearing jams Paper Jams Paper Jams HP CLJ CM6030. 6040 Clear jam in tray 1 Comments There are no comments for this article. Add Comment Nickname: Your Email: Subject: Comment: Enter the code below: Intranet Wiki by: KnowledgeBase Manager Pro v6.2.2 Knowledge Base JavaScript must be enabled in order for you to use Knowledgebase Manager Pro. However, it seems JavaScript is either disabled or not supported by your browser. To use Knowledgebase Manager Pro, enable JavaScript by changing your browser options, then try again. Learn more.
here for a quick overview of the site Help Center Detailed answers to any questions you might have Meta Discuss the workings and policies of this site About Us Learn more about Stack Overflow the company Business Learn more about hiring developers or posting ads with us Super User Questions Tags Users Badges Unanswered Ask Question _ Super User is a question and answer site for computer enthusiasts and power users. Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the top Motor not working on HP Laserjet 2300 (error 13.01.00) up vote 2 down vote favorite I have an HP Laserjet 2300 printer and it suddenly stopped printing. Whenever I try to print something, it reports the error code "13.01.00" which normally means that there is a paper jam in one of the trays. Only there is no jam. I searched for an answer for a few hours and tried all the tips I found, including: removing all dirt and dust checking the spring mechanism in the paper tray which pushes the paper up checking the pickup roller checking the sensor flag next to the pickup roller When checking the pickup roller I tried printing a test page with the tray out by pressing up the sensor flag and I noticed that the pickup roller is not even moving. The printer seems to be trying to move it, but stops after two attempts, each of which is accompanied by a clicking sound. It then stops and reports the error message. So it seems there is some problem with the motor or the gears. Maybe someone has had this problem too and might be able to provide some insight. printing printer hp-laserjet laserjet share|improve this question edited Jul 15 at 7:30 Hennes 51.1k776121 asked Jul 30 '15 at 16:02 spyx 112 add a comment| active oldest votes Know someone who can answer? Share a link to this question via email, Google+, Twitter, or Facebook. Your Answer draft saved draft discarded Sign up or log in Sign up using Google Sign up using Facebook Sign up using Email and Password Post as a guest Name Email Post as a guest Name Email discard By posting your answer, you agree to the privacy policy and terms of service. Browse other questions tagged printing printer hp-laserjet