Lj 4300 Error Codes
Contents |
by peer An hp laserjet 4250n 49.4c02 service error error condition occurred while reading data from the network. Please retry your request. Your cache administrator is webmaster. Generated Thu, 20 Oct 2016 08:44:51 GMT by s_wx1011 (squid/3.5.20)
Stephen on Aug 25, 2004 at 5:32pm Add comment Please sign in to comment 0 hp 4300 error 68.8 permanent storage full message on power up
13.98 Paper Jam
any help out there??? by Anonymous on Sep 1, 2004 at 7:42am Add hp laserjet error codes comment Please sign in to comment 0 I would try a NVRAM reset. Remove any installed accessories (example stapler/stacker). Turn the 82.0180 eio 2 error printer off. Hold the down arrow while powering on the printer until all three lights come on and stay on. Press the up arrouw button. Press the pause/resume button. The display should show skip http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422 disk load. Press up arrow unitl NVRAM INIT is highlighted. Press select. NVRAM will be initialized and the printer will go through normal startup sequesnce. If this does not work you may need a new formatter. Also any custom setting different than factory default you programmed into the printer will be lost and have to be done again. by dmzcompute on Sep 1, 2004 at 8:03am Add comment Please http://www.fixyourownprinter.com/posts/21972 sign in to comment I held down the select button until all the lights stayed on. I hit the up arrow, but when I hit "Pause/Resume" button, nothing happens. The screen stays at New Maintance Kit. I have an HP4300. - Anonymous 0 error code message 59.4 is a problem with Toner cartridge motor - Motor M102 (reference of part for 4300 printers: RH7-1576-020CN)You can try an other cartridge, and start printer without cartridge if problem persists you need to change the M102 motor with the reference above.Thanks and regards by unknown on Jul 6, 2005 at 7:25am Add comment Please sign in to comment 0 I'm sorry, I misread that. You said the "Down arrow." Unfortunatly, that did not help either. by Anonymous on Jun 19, 2007 at 11:41am Add comment Please sign in to comment 0 1. Use the following Pin Codes:For LaserJet 4200 (11420002)For LaserJet 4300 (11430002)2. Press the SELECT Button to open the Menus.3. Now use the UP Arrow or DOWN Arrow Buttons to scroll to SERVICE.4. Once at SERVICE, Press the SELECT Button.5. Now press the UP or DOWN Arrow Buttons until the first digit of the Pin Code appears.6. Now press the SELECT Button to save that digit7. R
Printer Error Codes and Support Error: 10.XX.YY SUPPLY10.XX.YY SUPPLYMEMORY ERRORor10.XX.YY SUPPLYMEMORY ERRORFor help press ? Access deniedMENUS LOCKED 13.01.00. JAM IN TRAY x BAD https://www.orionmarket.com/product_error_page/HP/HP-4300/ DUPLEXERCONNECTION 13.02.00 JAM IN TOP BAD ENV FEEDERCONNECTION 13.03.00 JAM IN TRAY http://www.printertechs.com/printer-troubleshooting/370-13-20-error-on-hp-laserjet-4200-or-hp-laserjet-4300-series x CANNOT DUPLEX Check rear binorCANNOT DUPLEX Check paper 13.05.00 JAM IN TOP CARTRIDGE FAILUREFor help press ?alternates withRETURN FOR REPLACEMENTFor help press ? 13.06.00 JAM INSIDE REARDOOR CHOSEN PERSONALITYNOT AVAILABLEFor help press ?alternates withCHOSEN PERSONALITYNOT AVAILABLETo continue press "CheckMark Icon" 13.12.00 JAM INSIDE REARDOOR CLOSE TOP COVERFor help hp laserjet press ? 13.12.07jam in stapler DATA RECEIVEDTo print last page press "CheckMark Icon" 13.12.08jam in output device DETECTABLE SIZEIN TRAY XXFor help press ?alternates withDETECTABLE SIZE IN TRAY XXRecommend moveswitch to STANDARD 13.12.09jam in output deviceNOTE: The stacker or stapler/stacker LEDblinks in amber. DISK DEVICEFAILUREalternates withReadyFor menus press "CheckMark Icon" 13.12.10jam in output device NOTE: The event log records this errormessage as hp laserjet 4200 13.12.0A.NOTE: The stacker or stapler/stacker LEDblinks in amber. DISK FILEOPERATION FAILED 13.12.11jam in output device NOTE: The event log records this errormessage as 13.12.0B.NOTE: The stacker or stapler/stacker LEDblinks in amber. DISK FILESYSTEM IS FULLalternates withReadyFor menus press "CheckMark Icon" 13.13.00JAM INSIDE DUPLEXER DISK ISWRITE PROTECTEDalternates withReadyFor menus press "CheckMark Icon" 13.1C.00FUSER JAM EIO X DISKNOT FUNCTIONALFor help press 13.20.00 JAM IN TOP ENVELOPE FEEDEREMPTY 13.21.00 JAM IN TOP FLASH DEVICEFAILUREalternates withReadyFor menus press "CheckMark Icon" 13.98.00 FLASH FILEOPERATION FAILEDalternates withReadyFor menus press "CheckMark Icon" 13.XX.YYDUPLEX JOB INTERRUPTEDFor help press ? FLASH FILESYSTEM IS FULLalternates withReadyFor menus press "CheckMark Icon" 13.XX.YYJAM For help press ? FLASH ISWRITE PROTECTEDalternates withReadyFor menus press "CheckMark Icon" 20INSUFFICIENT MEMORY Incorrect 21 PAGE TOO COMPLEX INSERT OR CLOSETRAY XXFor help press ? 22 EIO XBUFFER OVERFLOW INSTALL CARTRIDGEalternates withFor help press ? 22 PARALLEL I/OBUFFER OVERFLOW INSTALL FUSERFor help press ? 40 EIO X BADTRANSMISSION LOAD TRAY XX{TYPE} {SIZE}For help press ? 41.3 UNEXPECTEDSIZE IN TRAY XX LOAD TRAY XX{TYPE} {SIZE}For help press ?alternates withLOAD TRAY XX{TYPE} {SIZE}To use anothertray press "CheckMark Icon" 41.XPRINTER ERROR Lower the op
Account Login Shopping Cart My Account Checkout Home Troubleshooting 13.20.00 Jam in Top Cover Area Error on HP LaserJet 4200 or HP LaserJet 4300 series Email 13.20.00 Jam in Top Cover Area Error on HP LaserJet 4200 or HP LaserJet 4300 series If you see this error code 13.20.00 "Jam in Top Cover Area" on either an HP LaserJet 4200 or HP LaserJet 4300 series printer, the printer either has a sensor blocked or it has an incorrect model fuser installed. The most common area for paper to jam is underneath the toner; first pull your toner cartridge out and verify there is no paper stuck in that area. If that area looks clean, you can take a thin cardboard (like a manilla folder or similar) and trim it to Letter size 8 1/2" by 11". Turn the power off, remove Tray 2, and gently feed the manilla folder into the paper path for Tray 2. You are trying to knock loose any obstructions in the path, like bits of paper, staples. Insert that in and work it gently up and down. Reinstall Tray 2 and see if your manuevering cleared the error. If not, you should check the little black plastic sensor flag near the registration assembly, sits near the front middle, underneath the toner. Verify that tiny plastic sensor is in good working order and operates properly (it should have an attached spring and should move back and forth to the touch.) If you don't find any actual paper jammed and the sensor seems to move freely, you should verify the fuser is correct by checking the part # on the fuser, see details below. When you see this 13.20.00 error, you should verify you have the correct fuser installed for your model. HP makes 3 different fusers which look identical, but the 3 fusers are not interchangeable between printer models. The outside plastic and metal frame look the same, but the inner wiring is different. If the incorrect fuser is installed, you can get a 13.20.00 error (or a 50.5 error in some cases) when you power on the printer. Fusers are a consumable part and are sold as part of a maintenance kit; it is expected over the life of the printer you will replace the fuser several times. HP estimates average fuser life to last between 150,000 to 200,000 pages; but a fuser can fail much earlier depending on printing conditions, heavy paper jams, and the quality of the fuser installed. The best way to determine which fuser you have is to pull the fuser out of your printer and check the barcode label on the fuser. If yo