Internal Error Delivery Report Out Of Range
local l/L remote r/R ... qmail-send is waiting for l local deliveries and r remote deliveries. The concurrency limits are L and R. status: exiting qmail-send is done. FATAL PROBLEMS alert: cannot start: ... qmail-send is unable to prepare itself for delivering messages; it is giving up. This normally indicates a serious configuration error, but it can be caused by a temporary lack of resources. alert: oh no! lost ... One of the other daemons has died. qmail-send will exit as soon as possible. SERIOUS PROBLEMS alert: unable to append to bounce message... qmail-send is unable to record a permanent failure, usually because the disk is full. This is a very serious problem; qmail-send cannot proceed without recording the results. It will try again in ten seconds. alert: out of memory... qmail-send tried to allocate more memory and failed. It will try again in ten seconds. alert: unable to opendir... qmail-send is having trouble reading a file list from disk, usually because the system's file descriptor table is full, but possibly because permissions are set incorrectly. It will try again in ten seconds. alert: unable to switch back... qmail-send was sent SIGHUP, and it is unable to reenter the queue directory. This is a very serious problem; qmail-send cannot proceed outside the queue directory. It will try again in ten seconds. alert: unable to reread... qmail-send was sent SIGHUP, but it is unable to read the new controls. It will continue operating with the original controls. MESSAGES new msg m qmail-send is going to preprocess a queued message. The message number, m, is its disk inode number. After a message is removed from the queue, its number can be reused immediately. info msg m: bytes b from qp q uid u Message m contains b bytes; its envelope sender is s; it was queued by a user with user ID u. q is a long-term queue identifier, the process ID of the qmail-queue that queued the message. bounce msg m qp q Message m had some delivery failures. The lo
first and patched in to a clean source tree as root.warning: internal error: delivery report out of rangeThere are old ref's to this talking about qmail-send.c and the inccorecterror reporting http://fmatrm.if.usp.br/cgi-bin/man/man2html?qmail-log+5 of qmail-spawnlRegardsRichard Claudio Jeker 2004-05-13 14:33:11 UTC PermalinkRaw Message Post by RichardHi,Can you guys Fix this ?http://www.qmail-ldap.org/qmail/qmail-ldap-1.03-20040401.patch.gzI gunzipped first and patched in to a clean source tree as http://qmail-ldap.argus.pipeline.narkive.com/p8b4EckM/warning-internal-error-delivery-report-out-of-range root.warning: internal error: delivery report out of rangeThere are old ref's to this talking about qmail-send.c and the inccorecterror reporting of qmail-spawnlWhat system are you using? I'm unable to reproduce this.I have found a race condition this morining in this code but I don't thinkthat it is simple to trigger this race.--:wq Claudio 1 Reply 1 View Switch to linear view Disable enhanced parsing Permalink to this page Thread Navigation Richard 2004-05-13 13:56:35 UTC Claudio Jeker 2004-05-13 14:33:11 UTC about - legalese Loading...
ApplicationFREE iPad ApplicationBooksBlog HomeQuality Quality Control Details Last Update On : 2013-03-03 Quality control is designed to detect, reduce, and correct deficiencies in a laboratory’s internal analytical process prior to the release of patient results.Quality control http://www.clinlabnavigator.com/quality-control.html samples are special specimens inserted into the testing process and treated as http://www.fehcom.de/sqmail/man/qmail-log.html if they were patient samples by being exposed to the same operating conditions. The purpose of including quality control samples in analytical runs is to evaluate the reliability of a method by assaying a stable material that resembles patient samples.Quality control is a measure of precision or how well internal error the measurement system reproduces the same result over time and under varying operating conditions.Pathologists need to be involved in development of quality control protocols, the selection of quality control materials, long term review of quality control data, and decisions about repeating patient samples after large runs are rejected.These quality control activities play an important part in assuring the quality of laboratory tests. internal error delivery Quality control material is usually run at the beginning of each shift, after an instrument is serviced, when reagent lots are changed, after calibration, and when patient results seem inappropriate.A quality control scheme must be developed that minimizes reporting of erroneous results, but does not result in excessive repitition of analytical runs. The manufacturer should recommend in their product labeling the period of time within which the accuracy and precision of the instruments and reagents are expected to be stable.Each laboratory should use this information to determine their analytical run length, taking into consideration sample stability, reporting intervals of patient results, cost of reanalysis, work flow patterns, and operator characteristics.The user's defined run length should not exceed 24 hours or the manufacturer's recommended run length.Quality control samples must be analyzed at least once during each analytical run.Manufacturers should recommend the nature of quality control specimens and their placement within the run.Random placement of quality control samples yields a more valid estimate of analytical imprecision of patient data than fixed placement and is preferable. Quality control materials should have the following characteristics.They shoul
are L and R. status: exiting qmail-send is done. FATAL PROBLEMS alert: cannot start: ... qmail-send is unable to prepare itself for delivering messages; it is giving up. This normally indicates a serious configura- tion error, but it can be caused by a temporary lack of resources. alert: oh no! lost ... One of the other daemons has died. qmail-send will exit as soon as possible. SERIOUS PROBLEMS alert: unable to append to bounce message... qmail-send is unable to record a permanent failure, usually because the disk is full. This is a very serious problem; qmail-send cannot proceed without recording the results. It will try again in ten seconds. alert: out of memory... qmail-send tried to allocate more memory and failed. It will try again in ten seconds. alert: unable to opendir... qmail-send is having trouble reading a file list from disk, usu- ally because the system's file descriptor table is full, but possibly because permissions are set incorrectly. It will try again in ten seconds. alert: unable to switch back... qmail-send was sent SIGHUP, and it is unable to reenter the queue directory. This is a very serious problem; qmail-send cannot proceed outside the queue directory. It will try again in ten seconds. alert: unable to reread... qmail-send was sent SIGHUP, but it is unable to read the new controls. It will continue operating with the original con- trols. MESSAGES double bounce: discarding ... Message m was discarded due to an 'empty' recipient in double- bounceto. triple bounce: discarding ... Message m had some delivery failures, but it is already a dou- ble-bounce message, so it must be thrown away. Triple-bounce messages do not exist. end msg m qmail-send is about to remove message m from the queue. DELIVERIES starting delivery d: msg m to ... qmail-send is telling qmail-lspawn or qmail-rspawn to deliver message m to one recipient. The delivery number, d, starts at 1 and increases by 1 for each new delivery. delivery d: success: ... Delivery d was successful. delivery d: failure: ... Delivery d failed permanently. The message will bounce. delivery d: deferral: ... Delivery d failed temporarily. This recipient will be retried later. delivery d: report mangled, will defer There is a serious bug in qmail-lspawn or qmail-rspawn. This recipient will be retried later. WARNINGS internal error: delivery report out of range qmail-lspawn or qmail-rspawn has supplied a report on a nonexi