Internal Error Oops 807
Timing Data Converters Development Tools Digital Signal Processors (DSP) DLP® Products & MEMS Embedded Software Interface Isolation Logic Microcontrollers OMAP™ Applications Processors (Read Only) Power Management RF & Digital Radio Sensor Products Haptics & Touch Wireless Connectivity /etc Support Blogs Analog Wire Analog: The real world Behind the Wheel ConnecTIng Wirelessly Enlightened: The TI DLP® Blog Fully Charged Industrial Strength Launch Your Design Learn E2E Motor Drive & Control MSP Low-Power Plays On the Grid Power House Precision Hub The Process Think. Innovate TI Live @... Tools Insider University Program Groups Corporate Citizenship TI University Program Russian E2E (сообщество E2E) Japanese E2E (日本語コミュニティ) Learn E2E Launch Your Design Motor Drive & Control Videos More Cancel DaVinci™ Video Processors Video Processor DM64x DaVinci Forum Mentions Tags More Cancel Sign In to Post Sign In to Post Cancel Go to Digital Signal Processors (DSP) Forums Amplifiers Switches & Multiplexers Applications Processors Clock and Timing Data Converters Development Tools Digital Signal Processors (DSP) DLP® Products & MEMS Embedded Software Interface Isolation Logic Microcontrollers OMAP™ Applications Processors (Read Only) Power Management RF & Digital Radio Sensor Products Haptics & Touch Wireless Connectivity /etc Support Announcements Amplifiers Switches & Multiplexers Applications Processors Clock and Timing Data Converters Development Tools Digital Signal Processors (DSP) DLP® Products & MEMS Embedded Software Interface Isolation Logic Microcontrollers OMAP™ Applications Processors (Read Only) Power Management RF & Digital Radio Sensor Products Haptics & Touch Wireless Connectivity /etc Support More Cancel Not Answered Internal Error: Oops: 807 [#2] Intellectual 330 points JT4589 Hi All, I am using kernel 2.6.10, DSPLINK Module (1.40.05_p1) and CMEMK version 0x2000000. We'v
messages) https://e2e.ti.com/support/dsp/davinci_digital_media_processors/f/99/t/5835 1. 2007-06-18 Re: Error while rebooting Linux - Internal error: Oop linux-arm Midhun Agnihotram 2. 2007-06-18 Re: Error http://marc.info/?t=118198682700001&r=1&w=2 while rebooting Linux - Internal error: Oop linux-arm Russell King - ARM 3. 2007-06-16 Error while rebooting Linux - Internal error: Oops: 8 linux-arm Midhun Agnihotram 4. 2007-06-16 Re: Error while rebooting Linux - Internal error: Oop linux-arm Russell King - ARM Configure | About | News | Addalist | SponsoredbyKoreLogic
ARM Linux
Forum Device and Tools Related SoC Discussion SoC Linux Cyclone V Dev Board - Problem using sopc2dts If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. Page 1 of 2 12 Last Jump to page: Results 1 to 10 of 17 Thread: Cyclone V Dev Board - Problem using sopc2dts Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… Search Thread Advanced Search Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode February 24th, 2015,11:27 AM #1 jpe1313 View Profile View Forum Posts Altera Teacher Join Date Jul 2008 Posts 141 Rep Power 1 Cyclone V Dev Board - Problem using sopc2dts Thanks in Advance. We are using Qsys/Quarturs 14.1. Our linux release is Poky 8.0 - Linux version 3.9.0 We have taken the GSRD for the Cyclone V and added to the design a 16550 serial port on the HSMC connector. Then I have taken the generated *.sopcinfo to create the new *.dtb file utilizing the following command: sopc2dts --input gsrd_modified.sopcinfo\ --output socfpga.dtb\ --type dtb\ --board soc_system_board_info.xml\ --bridge-removal all\ --clocks I then replace the original *.dtb file with the newly created *.dtb file on the microSD card. While booting I get some WARNING messages with traces and the final message with a trace is: Unable to handle kernel paging at virtual address c08d400c ... Internal error: Oops: 807 [#1] SMP ARM ... I am enclosing the complete boot message. Am I doing something wrong in creating the *.dtb file? Is there a later kernel version I should be using? Attached Files CycloneVEvalBoard-bootMessages-24Feb15.txt (17.6 KB, 2 views) Reply With Quote February 24th, 2015,01:59 PM #2 jpe1313 View Profile View Forum Posts Altera Teacher Join Date Jul 2008 Posts 141 Rep Power 1 Re: Cyclone V Dev Board - Problem using sopc2dts O.K. So in working more. I realized that I was mixing 13.1 files with 14.1 files. I had been using 13.1 with the Cyclone V Dev Kit but updated yesterday to Quartus 14.1. So there was one more *.xml file that is needed in the command above. "--board hps_common_board_info.xml" I haven't done