Canon Digital Camera Error Code E18
Contents |
when anything prevents the zoom lens from properly extending or retracting.[1] The error has become notorious in the Canon canon lens error restart camera user community as it can completely disable the camera, requiring expensive repairs.
Lens Error Canon S100
ConsumerAffairs.com reports that the "lens has a feature called bellows claw, which is a gear that physically extends and canon lens error 01 retracts the lens. A piece that holds the lens, the barrier plate, is not large enough and can sometimes cause the bellows claw to malfunction, resulting in a stuck lens".[citation
Canon Camera Lens Error Will Shutdown Automatically
needed] The result is a black screen that only contains the error message, E18. Another problem mentioned on the site blames a sticky iris in the lens, caused by grease entering inside from the microphones built into the lens. The buildup freezes up the ability of the lens to open. Although the use of the E18 error coding made this problem seem canon s110 lens error fix to be the particular domain of Canon cameras, the problem is actually quite common throughout all cameras with telescopic lens barrels. As a result, Canon has since dropped the use of this error code in its newer cameras. In its place it has adopted the more common term "lens error" that other manufacturers use. As such, its newer cameras report this term when the problem occurs. Contents 1 Causes 2 Repairing the E18 error 3 Consumer response and class action 4 References 5 External links Causes[edit] According to Canon, one may get an E18 due to any of the following: Camera activating and lens opening while in a confined space or being blocked Extracted lens getting jarred Low battery condition as the unit is turned on or off Dropping of the camera Foreign substances, such as dust, sand or dirt entering into the camera body. General jarring of the camera "General camera malfunction" One major contributor to E18 lens errors is the improper use of camera cases, or the carrying of cameras in pockets. An inadvertent activation of the camera while i
Amazing story about Canon E18
How To Restart Canon Camera
- Links to Canon E18 resources Bosch E18 Error -
Canon Powershot A4000 Lens Error
How to repair a Bosch E18 error code DSTV E18 Error - How to repair lens error canon sx530 a DSTV E18 error code - How to repair a DSTV 8118 error code - Full list of DSTV error codes - Link to https://en.wikipedia.org/wiki/E18_error us - Contact Us Canon's official explanation of the E18 error This is the official explanation of the E18 error found on Canon's web site: Error Code "E18" (Lens unit/Lens cover error) When a camera error occurs, an error code like "Exx" will be displayed, where the x's represent numbers. http://www.e18error.com/canon.html The "E18" error code indicates an error that involves the lens unit or lens cover. Or it may appear if you apply pressure to the area surrounding the lens while handling the camera. Solution Check the following when you operate the camera to avoid applying pressure to the lens and surrounding area: - Hold the camera so that your fingers do not touch the lens unit when you are shooting. - Make sure the camera is off before you put it back in the case. If you cannot clear the error code by turning the camera off and then on again, or if the error code is displayed frequently, a camera malfunction may have occurred. Please contact the retailer where you purchased the camera or the nearest Canon service center. --- Copyright © 2006-2014 ------ Canon E18 error - www.e18error.com ---Privacy Policy - Refund Policy
on my Canon PowerShot SD450, which prevented my lens from extending when the power was turned on, and the fix wasn’t nearly as difficult as I had expected. I’ve even snapped some shots of the process so that you can follow along at home, https://blog.wolffmyren.com/2008/10/23/e18-error-fixed-canon-powershot-sd450/ and fix your own camera if you are experiencing the same problem that I was. If you’re not yet familiar with the E18 error, check out this information on the topic from Wikipedia: The E18 error is an error message http://arstechnica.com/civis/viewtopic.php?t=226904 on Canon digital cameras. The E18 error occurs when anything prevents the zoom lens from properly extending or retracting.[1] The error has become notorious in the Canon user community as it can completely disable the camera, requiring expensive repairs. lens error (http://en.wikipedia.org/wiki/E18_error) This is a fairly prevalent problem with the PowerShot cameras, and a class action lawsuit was filed (but dismissed) against Canon: A Chicago law firm, Horwitz, Horwitz & Associates, has already filed a class action,[4] while the law firm of Girard Gibbs & De Bartolomeo LLP are investigating this camera flaw and may issue a class-action lawsuit against Canon.[5] There is at least one other.[6] Although the suit was dismissed in a court of law, the plaintiffs canon lens error are appealing. Fortunately, at least in my case, the fix did not require returning the camera to a Canon repair facility or having to take unreasonably complex steps. My solution for the PowerShot SD450/IXUS 55 follows: (You’ll need a very small Philips head screwdriver, #00, to remove the screws) There are six screws holding the metal frame of the camera body together, two on each side, and two on the bottom. Remove all screws, pop the strap-hook plate (sorry, probably not the most technical term there), then gently lift the front plate off by pulling up from the bottom, and remove the back plate in the same fashion. These should come off relatively easily. This is what the camera should look like as you remove the plates: Now, looking from the top of the camera, you should see a small motor on the left side, as shown below (it’s beneath the cable with a “22” written on it): Take your screwdriver (or another small instrument) and gently try to rotate the plastic piece attached to the motor on the left side, as shown below: At this point, try placing the battery back in the camera (if you have removed it), turn the camera to one of the capture modes, and press the power button. If all went well, your lens should now be able to extend and retract properly. Further information (and other r
Case and Cooling Fetish CPU & Motherboard Technologia Mobile Computing Outpost Networking Matrix Other Hardware Agora Classifieds Ars DIY Forum (Name TBD!) Operating Systems & Software Battlefront Microsoft OS & Software Colloquium Linux Kung Fu Windows Technical Mojo Distributed Computing Arcana Macintoshian Achaia Programmer's Symposium The Server Room Ars Lykaion Gaming, Extra Strength Caplets The Lounge The Soap Box The Boardroom The Observatory Ars Help & Feedback Ars Subscription Member Areas Image Galleries Dreaded Canon S2 IS E18 Error: how to disassemble and fix 9 posts general Ars Praefectus Tribus: An IDIOT would only consider the up front cost Registered: May 29, 2002Posts: 3906 Posted: Sat Feb 24, 2007 6:27 pm I have started getting the E18 error that apparently is far too common on Canon cameras. I'm disappointed as I had a high opinion of them until this.I've done my research online and none of the proposed solutions work. I want to take it apart to make sure that there isn't any debris jamming the lens. Basically, when I turn it on the lens feels like it is trying to move forward, but never moves more than 1/2 MM or so. Does anyone know where I can find instructions on how to do this? I don't really want to spend $100 at a camera shop for a camera that now isn't worth much more than that. Any advice would be appreciated. Xevion Moderator et Subscriptor Registered: Oct 30, 2000Posts: 18642 Posted: Sat Feb 24, 2007 6:50 pm quote:I have started getting the E18 error that apparently is far too common on Canon cameras. I'm disappointed as I had a high opinion of them until this. Far too common? Other manufacturers' cameras get similar errors, and keep in mind that Canon has a tremendous marketshare percentage, so you are going to hear about more problems with Canon cameras than you will with HP, for example.Send it back in to Canon, and see how much they will charge to replace it. They might offer you a significant discount on a new camera, or the repair might be surprisingly cheap, or they might even fix it for free, even though it is out of warranty. On one occasion, I sent in an out of warranty camera for repair, and they fixed it for me, free. general Ars Praefectus Tribus: An IDIOT would only consider the up front cost Registered: May 29, 2002Posts: 3906 Posted: Sat Feb 24, 2007 6:59 pm Thanks Xev. Good points. I think it was your recommendation that led to me this. I bought it from someone who said he got it last April, so I'll send it in to them and see what happens. What's my next step up in the Canon