Aix Led Error Codes
Contents |
The remote host or network may be down. Please try the request again. Your cache administrator is webmaster. Generated Fri, 30 Sep 2016 04:07:32 GMT by s_hv1002 (squid/3.5.20)
Eurosoft/Mylex Faraday A-Tease HP IBM Landmark Microid Research/Mr NCR Olivetti Phillips Phoenix Quadtel Supersoft Tandon Zenith Intel Motherboards: CA810E CC820 SE440BX-2 D810E2CB D810EMO D815BN D815EEA D815EPEA D820LP SE440BX SR440BX http://www.bioscentral.com/misc/ibmdiag.htm JN440BX LB440GX/L440GX N440BX/NA440BX OR840 T440BX RC440BX VC820 For their PS/2 systems, IBM used a system of diagnostic codes to diagnose trouble spots in a given computer. The problem was, these diagnostic http://www.unixwerk.de/aix/ledcodes.html codes were never really documented all that well. The codes that I am presenting here are from documents I have read through, found on the web, found in old books, documents error codes and technical papers. As a computer technician, I rely on documentation to guide me through these types of messages. Therefore, I hope to provide this to all those other technicians out there who get the opportunity to work on one of these. And, yes, people still use them and some refuse to give them up. The method for reading these codes is aix led error pretty straight forward. The first part of the error code indicates the device that is causing the trouble. The second part gives the meaning of the error. You can think of the first part as the test code and the second part as the fault code. A fault code of 00 indicates that no problem was found. Thus 200 means the system memory was tested. The 00 means that no fault was found. 201 would mean a memory error. 202 would mean memory address error; lines 00-15. This page is rather extensive and will be updated on a regular basis. Like all the other codes out there. If you know of any error codes that I am displaying incorrectly or that aren't here. Let me know and I'll get it corrected as soon as I can. Thanks to Mike Rose for erors 129 and 229! System Board Errors: Code Description 101 System board interrupt failure (unexpected interrupt) 102 BIOS ROM checksum error (PC, XT); timer error (AT, MCA) 103 BASIC ROM checksum error (PC, XT); timer interrupt error (AT, MCA) 104 Interrupt control
Eintrag in unser Gästebuch KontaktNehmen Sie Kontakt mit den Autoren auf ArchivAlle Unixwerk- Artikel seit 2003 unixwerk > AIX > ledcodes 22. Oktober 2011 Die LED-Codes von AIX Inhalt Der Ernstfall: Blinkende Achten Die dreistelligen LED-Codes LPAR-Bootcodes Weiterführende Informationen Die dreistelligen LED-Codes von AIX kommen aus der Zeit der alten MicroChannel-basierten RS/6000 mit drei 7-Segment-Anzeigen; neuere Maschinen haben eine Stelle mehr, die aber von AIX nicht genutzt wird, dort wird eine Null angezeigt. Größere Maschinen haben ein noch viel längeres Feld, in dem bisweilen Zusatzinfos angezeigt werden. In diesem Artikel geht es nur um die dreistelligen AIX-Codes; alles was davor angezeigt wird (Exxx,...), ist von Maschine zu Maschine unterschiedlich und findet sich im entsprechenden Handbuch. 1. Der Ernstfall: Blinkende Achten Drei blinkende Achten bedeuten nichts Gutes: Die Maschine ist stehengeblieben und versucht einen Dump wegzuschreiben. Auf Maschinen mit mehr als 4 Ziffernstellen (s.o.) werden hinter den drei Achten weitere Stellen angezeigt: ein dreistelliger Code (meistens 102 = Systemstillstand) ein weiterer dreistelliger Code, der Aufschluss über den Grund des Stillstandes (HW/SW) geben kann. Die Bedeutung solcher Codes kann aus der entsprechenden Sektion weiter unten ermittelt werden. und ein letzter dreistelliger Code, der über Erfolg oder Misserfolg beim Schreiben des Dumps informiert (=> 0C0 - 0C9) Diese weiteren Informationen lassen sich auch bei Maschinenmit nur 3 oder vier Ziffernstellen ermitteln: Dazu wird die Reset-Taste gedrückt. Nachdem ersten Drücken erscheint der Fehler-Code (1), nach dem zweiten der Dump-Code (2). 2. Die dreistelligen LED-Codes Folgende Bereiche von LED-Codes kennt AIX: 0C0 - 0C9 100 - 195 200 - 2E7 301 - 325 42C + 43C 500 - 5C6 600 - 6C8 700 - 7C6 800 - 8CC 900 - 99C c00 - c99 (neu) Im Einzelnen: 0C0 - 0C9 AnzeigeBeschreibung 0C0A user-requested dump completed successfully 0C1An I/O error occurred during the dump 0C2A user-requested dump is in progress 0C4The dump ran out of space 0C5The dump failed due to an internal error 0C7Progress indicator. Remote dump in progress 0C8The dump device is disabled. The current system configuration does not designate a device for the requested dump 0C9A system-in