Leica Disto A3 Error 288
completa Visualizzazione ProPacks The endpiece is an integral part of the tool, connected to the circuit board. In the closed position the DISTO knows to measure from its base. Flip it open 90 degrees to align the base perfectly on an edge or corner. Flip leica error codes it out all the way and you can put this baby in a corner to disto error 284 accurately measure diagonals. Otherwise, the width of the base would prevent you from getting all the way into the corner, rendering leica gps 1200 error codes the measurement inaccurate. Smart Horizontal combines a tilt sensor and software to add several useful features to a DISTO, including Height Tracking, Profile Measurement, and Indirect Measurement, shown here. Often, the straight horizontal line we need to measure is obscured. Smart Horizontal allows you to shoot over the obstacle (1). The software uses the angle (a) to calculate the level distance to the target. Bluetooth-enabled DISTOs send measurements to other devices as they are taken. Drag and drop measurements onto layouts or images using the DISTO Sketch App (pictured) then send the specs as a PDF. DISTOs can see the laser point over 600’ away in direct sunlight and you can’t. Looking at the DISTO’s display, use the 4xzoom point-finding camera to zoom in close to your target. The crosshairs precisely indicate the position of the measuring point. This is a must-have feature for anyone working outdoors even 5% of the time. Measure in a Picture combines a fixed focal length lens, the Smart Horizontal tilt sensor, and the distance to the target to calculate the precise width of an object from a distance from a single measurement. DISTOs without this capability use the Pythagorean Theorem to determine width from a distance, which requires three separate measurements. SmartBase - Industry First Technology Smart Base is a biaxial pivot integrated with the DISTO circuit board. It enables the DISTO S910 to measure the distances and angles between multiple points from a fixed location. S910 D810 Touch D510 D410 X310 D2 D210 D110 D1 Precisione/Portata 1 mm • 300 m 1 mm • 200 m 1 mm • 200 m 1 mm • 150 m 1 mm • 120 m 1,5 mm • 100 m 1 mm • 80 m 1,5 mm • 60 m 2 mm / 40 m Terminale intelligente Yes Yes Yes Yes Yes Yes Smart Horizontal Yes Yes Yes Yes Yes Bluetooth V4.0 Smart V4.0 Smart V4.0 Smart V4.0 Smart V4.0 Sma
Solution 154 Transverse tilt >20° Hold the instrument without any transverse tilt 156 Transverse tilt > 10° Hold the instrument without any transverse tilt 160 Main tilt direction, angle too high (>45°) Measure angle up to +/- 45° 162 The calibration has not been accomplished on a leveled surface and the calibration value is respecitvely within an ineligible area. Calibrate the device on an absolute horizontal leveled surface. 203 Wrong measuring sequence for Pythagoras measurements Measure in correct sequence 204 Calculation error Repeat procedure 206 No endpiece detection Attach the endpiece properly. If error still occurs, replace the endpiece 217 Measuring module error Contact Us 240 Data transfer error Repeat procedure 245 2nd button http://lasers.leica-geosystems.com/it/blog/faq-error-messages pressed although no Bluetooth connection exists. Establish Bluetooth connection 252 Temperature too high, above 50°C Cool down the instrument 253 Temperature too low, below 0°C Warm up instrument 255 Receiver signal too low, measuring time too long, distance too long Use target plate, measuring time > 10 sec. 256 Receiver signal too strong Use target plate (white side) 257 Erroneous measurement, too much backlight Use target plate 260 Laser http://www.appraiserslaser.com/support/disto-error-codes/ beam was interrupted Repeat measurement 272-276 Measuring module error Contact Us 279 Measuring module error Contact Us 285-291 Measuring module error Contact Us 297-299 Measuring module error Contact Us 402 Measuring module error Contact Us 404 Measuring module error Contact Us 501-503 Measuring module error Contact Us 651 Measuring module error Contact Us 801-803 Measuring module error Contact Us This entry was posted in Uncategorized on April 1, 2014 by admin. Post navigation ← Saving your favorite functions on the programmable keys Search for: Categories Fuctions (39) Area and volume (3) Digital Pointfinder (5) Height tracking (1) Measure in Picture (7) Minimum / maximum (2) Painter (1) Profile Measurement (1) Pythagoras (4) Sloped object measurement (1) Smart Horizontal Mode (2) Stake-out (2) Tilt measurement (3) Trapezium (3) Triangle and Room Angle (2) Uncategorized (3) Disto Models Disto D330i Disto D810 Disto E7300 Disto E7400X Disto E7500i Obsolete Disto D5 Disto D8 Recent Posts Disto Error Codes Saving your favorite functions on the programmable keys How accurate is the tilt sensor? Lanyard / Hand Loop Installation Measure In Picture Archives April 2014 March 2014 January 2014 April 2013 March 2013 Disto Support, FAQ, and Knowledgebase by AppraisersLaser.com - © 2016 a Global Web Supply, LLC website
index Change font size FAQ Register Login Information The requested topic does not exist. Board leica disto a3 index The team • Delete all board cookies • All times are UTC - 6 hours [ DST ] POWERED_BY Cavechat RSS Feed Cavechat is the official caving forum of the National Speleological Society. The NSS is not responsible for the opinions expressed, and cannot verify the accuracy of information presented.