Motorola Xts 5000 Error Codes
Contents |
them to the e-mail address listed at the bottom of this article. The Spectra radios report most problems detected during the self-check on power up. These will be shown on the
Motorola Apx Error Codes
control head's Vacuum Fluorescent Display (VFD). They will be in one of three formats: motorola apx 7500 error codes ER xx/yy or ERROR xx/yy FL xx/yy or FAIL xx/yy FAIL nnn Where "xx" and "yy" will be hexadecimal characters motorola xts2500 fail codes (0-9, A-F), and "nnn" will be a decimal value (000-999). Problems displayed with the "xx/yy" format consist of a two-digit prefix ("xx") that identifies the source of the problem followed by a two-digit code ("yy")
Motorola Fail Codes
that specifies the particular problem. For example, a radio FAIL code may look like this: "FAIL 01/90", where the first two digits ("xx" in the format above, "01" in this example) identifies the source of the error and the second two digits ("yy" in the format above, "90" in this example) is a unique error code that identifies the particular problem or trouble. Problems displayed with the "nnn" format
Fail 01/90
are usually associated with temporary conditions that may go away if a different mode is chosen. A FAIL message is fatal and the radio will usually not work at all. Many ERROR messages will still allow the radio to work at reduced capacity, depending on the identified problem. For example, a disconnected external device or accessory will cause an ERROR message but the radio may still operate just fine without it. The A9 control heads can display 11 characters. Problems will be shown with the full word "ERROR" or "FAIL", followed by the error code prefix and error code. All other control heads with eight-character displays show the message beginning with "ER" or "FL". Hand-Held Control Heads (HHC) display errors with their two seven-segment LED characters by first flashing "Er" or "FL", then the error code prefix, then the specific error code. For the three-digit fail codes such as FAIL 001 or FAIL 999, the HHCH displays "FL 00 01" or "FL 01 99". These lists contain all the FAIL and ERROR prefixes and codes I could find in the manuals I have, but there are probably more. Use this list as a quick reference for locating problems. For example, if a radio is programm
Motorola land mobile radio equipment and their trunking technologies. Search Forums Show Threads Show Posts Tag Search Advanced Search Go to Page... motorola xtl 5000 maintenance mode LinkBack Thread Tools Search this Thread Display Modes #1 (permalink)
Motorola Xtl 2500 Error Codes
11-17-2012, 3:45 PM Metrofire31 Member Premium Subscriber Join Date: Dec 2002 Location: Western North Carolina motorola maintenance mode remote device Posts: 784 XTS 5000 Programming Today, when programming my XTS 5000 (UHF) I observed something I had never seen. Once programming was complete and I turned the radio http://www.repeater-builder.com/motorola/spectra/spectra-error-codes.html on, the came on for the first time saying "PLEASE WAIT". Then, it said "ERROR 09/10" and then my normal channels came up. The radio seems to be operating normally but I'm curious as to how to interpret the Error message. Anyone have any experience with this? Metrofire31 __________________ Metrofire31 WQIT636 - Atlanta Sponsored links #2 (permalink) http://forums.radioreference.com/motorola-forum/253462-xts-5000-programming.html 11-17-2012, 3:54 PM robertpearsall Member Shack photos Audio Feed Provider Join Date: Jun 2007 Location: Edison, NJ Posts: 541 That error has to due with secure make sure you dont have it checked in cps if the radio does not have it __________________ Motorola APX7000, Motorola CDM1250 ,Motorola Spectra, PSR500 x3, PRO404 ,PRO668 ,BCD436HP & Too many other Vintage Radios to list GMRS WQLT798 #3 (permalink) 11-17-2012, 4:00 PM ptolemy9200 Member Join Date: May 2012 Posts: 1,131 Sounds like you may have ADP enabled and the radio isnt capable of it. You may want to be sure the top knob isnt set for secure and clear for encryption. #4 (permalink) 11-18-2012, 12:09 PM Metrofire31 Member Premium Subscriber Join Date: Dec 2002 Location: Western North Carolina Posts: 784 XTS 5000 Programming Both of you gentlemen were right on target. Once I disabled "SECURE CAPABLE", the error message disappeared. I don't need the feature on my UHF radio anyway. Thank you both. Metrofire
Register Board index General General Motorola Solutions & Legacy Radio Discussion Search Users may not create topics, posts, or private messages containing or relating http://batboard.dreamhosters.com/viewtopic.php?t=84665 to the following material (especially pertaining to Motorola copyrighted software, unless you want Motorola to come along and shut this site down):Listing for sale or trade of, or links to sites offering for sale or trade of, or giving away, RadioService Software (RSS) or Customer Programming Software (CPS)Profanity, pornography, defamation, or slanderous remarks directed towards any error codes individual or entityCommercial advertising (except in the Batboard Vendors forum, as approved by the Admin/Mod Staff)Any other items which may be deemed as offensiveIf any topics, posts, or private messages containing or relating to the aforementioned material are brought to the attention of the Admin/Mod Staff, they will be deleted.Additional FAQ items appear here in Forum Rules. motorola xts 5000 Please review them for posting guidelines and further clarification. 09/10 error help The General forum is where users can discuss any topic regarding Motorola communications equipment - hardware, software, etc. There are also several focused forums on this board, so please take the time to ensure that your questions doesn't fall into one of those categories before posting here! Moderator: Queue Moderator Post Reply Print view Search Advanced search 5 posts • Page 1 of 1 kristofer886 New User Posts: 7 Joined: Thu Feb 05, 2009 2:18 am 09/10 error help Quote Postby kristofer886 » Tue Apr 21, 2009 1:52 am For all you experts out there. I have an issue. I have some radios that get the error 09/10 when receiving a encrypted digital transmission. I can find nothing wrong with the radios but there is some possible interference on the repeater. Is this a issue with the radio or interference. I know the 09/10 error is secure hardware failure, but when 2 radios do it at the
be down. Please try the request again. Your cache administrator is webmaster. Generated Wed, 19 Oct 2016 06:57:56 GMT by s_ac4 (squid/3.5.20)