Nortel Power Error Codes
Contents |
right) for diagnostic information during bootupand normal operation, when in service. Normally, it will display the configured loop and shelf number (LLLs). During power-up/boot When an MGC boots, diagnostic information from the nortel cs1000 error codes hardware and firmware tests appears on the faceplate. Messages that appear on the
E002 Unable To Send Registration Request To Call Server.
four-character LED display during MGC bootup are shown in the following table. In normal operation the messages appear in the following order: BOOT, POST, PASS, LOAD. If a fatal self-test error occurs, then PASS and LOAD do not appear. Instead an error code appears. MGC faceplate startup codes: Display Description BOOT This is the first message when display becomes active. POST Power on self test, appears while the MGC performs hardware system tests during system power up. PASS Power on self test pass. EXXX Error code where XXX is numeric. Appears if a serious system error is detected - see below. LOAD Application software is loading. During normal operation After the boot loader loads the CSP and starts to run, you can use the faceplate display for diagnostic information. During normal operation, the four-character LED displays the superloop and shelf number of the Media Gateway 1000E (MG 1000E) with MGC. If an error occurs that requires a diagnostic message to appear, then the display cycles between displaying the cabinet number and the error code. Each item appears for 20 seconds. The following table shows the messages that appear. MGC faceplate normal operation / error codes: Display Description EXXX Error code where XXX is a numeric value. An error code appears if a serious system error is detected. LLLS IPMG super loop and shelf, where LLL is the superloop number and S is the shelf number. Eg, 0320 or 1201. Note: the shelf digit is a special superscript character to differentiate it from the superloop number. E001 A 96 port daughter board is installed in DB position 2, this is not supported. Re-install it in position 1. E002 Unable to send registration request to call server. E003 Link down to call server. E004 Daughter board is not registered with call server. Additional messages are defined for the VoIP DSP Daughter boards. Home»Meridian»Install»Mgcdis
FORUMSFOR COMPUTER PROFESSIONALS Log In Come Join Us! Are you aComputer / IT professional?Join Tek-Tips Forums! Talk With Other Members Be Notified Of ResponsesTo Your Posts Keyword Search One-Click Access To YourFavorite Forums Automated SignaturesOn Your Posts Best Of All, It's Free! Join Us! *Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail. Posting Guidelines Promoting, selling, recruiting, coursework and thesis posting is forbidden.Tek-Tips Posting Policies Jobs Jobs from Indeed What: Where: jobs by Link To This Forum! Add Stickiness To Your Site By Linking To This Professionally Managed Technical Forum.Just copy and paste the BBCode HTML Markdown MediaWiki reStructuredText code http://pbxbook.com/meridian/install/mgcdiser.html below into your site. Nortel: CS1000 (Meridian) systems Forum at Tek-Tips HomeForumsWiring ClosetPhone SystemsNortel: CS1000 (Meridian) systems Forum error messages BSD090 & BSD000 thread798-1314636 Forum Search FAQs Links MVPs error messages BSD090 & BSD000 error messages BSD090 & BSD000 nadz22 (TechnicalUser) (OP) 19 Dec 06 15:49 i have a problem with this ERROR CODES BSD090 and BSD000,WE KNOW THE PROBLEM POWER FAULT INDICATION. WE HAVE DETECTED that the voltage on this http://www.tek-tips.com/viewthread.cfm?qid=1314636 card QPC82E is lower than 15 Volts and we already change the card with no difference detected... is there something else we could test for? we are at a loss...... we're using NORTEL MERIDIAN 1-71 OPTION 17,76 RE: error messages BSD090 & BSD000 PERRYPJ (TechnicalUser) 19 Dec 06 17:33 Let LD 45 run twice then do a CMAJ from LD 30 OLD ROLMEN WORKING ON NORTELS RE: error messages BSD090 & BSD000 GHTROUT (IS/IT--Management) 19 Dec 06 19:22 Agreed, but to expand...BSD000 is an overlay "indentifier" - it means LD45 is running or will run.BSD090 means "some power fault may exist" - but it may not exist.The Power Monitor card initiates the message and the card itself is often the problem if the switch is running without any noticable problems.The way to run a LD45 routine is:LD45then just type the word "test" and hit the enter key and wait GHTROUT.com | FAQs | Recent Replies Red Flag This Post Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework. Cancel Red Flag SubmittedThank you for helping keep Tek-Tips Forums free from inappropriate posts.The Tek-Tips staff will check this out and take appropriate action. Close Reply To This Thread Posting in
be down. Please try the request again. Your cache administrator is webmaster. Generated Fri, 21 Oct 2016 19:27:56 GMT by s_wx1085 (squid/3.5.20)