Oki 928 Fatal Error Problem
Contents |
by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if oki c610 fatal error 928 you need to. 100% Satisfaction Guarantee Rate the answer you receive. Ask
Power Off On 928 Fatal Error
Colin Vincent Your Own Question Colin Vincent, Engineer Category: Printers Satisfied Customers: 1544 Experience: City of Guilds 224, Kyocera, okidata error codes IBM, Novell certifications. 24 years IT experience. 29964247 Type Your Printers Question Here... Colin Vincent is online now oki c8600 928 fatal error code can you please tell me what Customer Question oki fatal error codes oki c8600 928 fatal error code can you please tell me what this means and any suggested remedies Submitted: 5 years ago. Category:Printers Share this conversation Expert: Colin Vincent replied5 years ago. Colin Vincent : Hi there. The error 928 is a fuser motor error (Motor overload). Usually caused by a siezed or damaged fuser preventing the motor from turning. You will likely
Oki C711 Fuser Reset
need to replace the fuser unit unless there is something obvious jamming it that you can remove. Ask Your Own Printers Question Share this conversation Related Printers Questions Question Date Submitted I am in the OR & need to scan document, My computer will not 10/21/2016 10/21/2016 Dustin CAN NOT GET PRINTER TO RESPOND TO PC AS IT ALWAYS HAD DONE. 10/21/2016 10/21/2016 Viet - Printer Tech MY HP officejet 6600 does not print the right colors 10/21/2016 10/21/2016 Shefin I have a 7500 series printer with a B203 error. Any Ideas, 10/21/2016 10/21/2016 Ashik I haven't used my BP officejet Pro 8600 for a couple of 10/21/2016 10/21/2016 Richard I have misplaced the software disc for my XP-610. We have 10/21/2016 10/21/2016 Ashik I am trying to print a letter off of Microsoft works and 10/21/2016 10/21/2016 Viet - Printer Tech My printer says its offline but everything is good, it's not 10/21/2016 10/21/2016 Viet - Printer Tech It says 0xE5 error and to turn it off. But, it continues to 10/21/2016 10/21/2016 Nathan TO GET MY LAPTOP TO CONNECT TO MY PRINTER AND IT WON'
status monitor may read oki c610 fuser "Fatal Error". This simply means a problem has occurred requiring action
Oki C610 Error Codes
to clear. A "Fatal Error" does not mean your printer will "die". Fatal Error explanations are not http://www.justanswer.com/printers/4kfy2-oki-c8600-928-fatal-error-code-can-please-tell.html usually found in the User's Guide or Handy Reference Guide. RECOMMENDED NEXT STEP: First, try turning off your printer then turning it back on. If this does not clear the message or remedy the http://my.okidata.com/oki-faq.nsf/faqcentral/F9BE1CE10EA6F3AA85257654006757C1?OpenDocument problem, check to see if your printer is on a power strip (or not plugged directly into the wall). For testing purposes, be sure the printer is plugged directly into the wall. Often, the issue is power-related. Second, if the issue persists after this, write down the message (including the 3-digit error code number) and email us at "support@okidata.com" or call Oki Data Customer Support (1-800-654-3282) for assistance. NOTE: If you see a series of letters and numbers(scrolling across the display) after the 3-digit error code, be sure to write these down also and report them when call or emailing Customer Support.
error" with the error code 980 Solution 1: Error 980 means that the error by media clinging to the fuser and the fuser is required to be replaced. Solution 2: Take out the Fuser and lay the two blue levers flat and remove them. Remove the two silver screws and separate the casing. Remove http://fix-your-printer.blogspot.com/2011/07/how-to-fix-error-code-980-on-oki.html the two black screws from the connector at the bottom of the fuser closest to the edge. Unravel and loosen the wires so you can pull that connector out a few inches so you can get a couple of wires in there. Insert a wire into each of the two holes on the back of that connector. 2 and 3 have wires going in, 4 and 5 dont which is the fuse. After you get the wires in the 2 holes, check for continuity from the end of the wires and the terminals fatal error if you can. Make sure the wires are long enough to hang out the case. Use the thinnest wires you can find. Run the wires out of the case and put the case back together and put the fuser in. Twist the two wires together and power up the machine. As soon as you here the first motor, which is about 5 seconds, pull the wires apart, you just reset the fuser back to 100% and cleared the "980" Fatal Error. Video: Libellés : Oki 35 comments: Iron It said... You can 928 fatal error replace the fuser but this won't always clear the error, the above method may work but seems an awful lot of workContact OKI via the website, they will reply with instructions on how to download and install Oki storage device manager. Once this is installed you can use it to send a .pjl file to the printer which clears the error. March 28, 2012 at 4:59 PM Anonymous said... I repaired oki c5800 980 error like author said, I put two wires inside fuser unit, on the white two free pins.. then I power on the printer and waited for first motor sound, then I released the wires (timing is critical) November 13, 2012 at 6:16 AM Anonymous said... I have the software to send a pjl file, can you tell me the pjl to send to erase the error 980 in Oki C5700 please. Thanks. December 12, 2012 at 2:36 AM Anonymous said... To Iron, my MC361 had an error 980. I replaced the fuser. I asked OKI support to help me clear the 980 error. They won't help you. OKI support told me to go service the printer at an OKI certified repair shop!!. I guess OKI support is like those car dealers who ask $80 to replace a burned light bulb when all you can easily do it yourself... it is all about money, not helping the customer.Never heard anything from OKI about a pjl file August 1, 2013 at 2:34 PM viridens said... I don't understand how this can work. The connections are made to unused pins. Surely the 2 pins you need to link to would be connected to the b