922 Error Fuser
Contents |
Account Login Shopping Cart My Account Checkout Home Troubleshooting 922 Service Fuser Error Lexmark T640 T642 T644 T650 T652 T654 Email 922 Service Fuser Error Lexmark T640 T642 T644 T650 T652 T654 If you are service fuser error lexmark printer seeing the '922 Service Fuser' message on your Lexmark T640, T642, T644,
Lexmark X654de Service Fuser Error
T650, T652, or T654 series printer , you probably need to replace the fuser assembly. This error message
Lexmark Fuser Replacement
indicates the fuser assembly, which bonds the toner to the paper, is failing to maintain the needed temperature. A fuser is a consumable part, over the life of the http://support.lexmark.com/index?page=content&id=SO4036&modifiedDate=11/14/13 printer you can expect to change a fuser several times. Fusers are sold as part of the preventative maintenance kit. Lexmark rates the life expectancy of a fuser around 150,000 pages, but a fuser can fail much earlier depending on printing conditions, paper jams, and the quality of the fuser installed. For a temporary fix, you can try turning the printer http://www.printertechs.com/printer-troubleshooting/381-922-service-fuser-error-lexmark-t640-t642-t644-t650-t652-t654 off and back on again, sometimes the reboot allows the fuser to reset so you can print a few more pages. Usually the error message returns quickly; in that case you should install a replacement fuser. Fortunately, replacing fusers on these model is not difficult. (Remove the back cover, unscrew 2 screws on the fuser, unplug the fuser, and pull the fuser assembly out.) We have installation instructions available. Call us with any questions toll-free 866-352-7108 or local 608-831-2396. See our links to purchasing info below. Purchasing information: Lexmark T640 , T642, T644 series fuser and maintenance kitPurchasing information: Lexmark T650 , T652, T654 series fuser and maintenance kit Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations from PrinterTechsGlossary of terms Home Site Map Policies Legal Back To Top © 2016 PrinterTechs.com Inc., PrinterTechs and the PrinterTechs logo are trademarks of Printertechs.com, Inc. and may not be used without advance written permission of PrinterTechs.com, Inc.
fuser unit, x2replaced assembly unitreplaced low http://www.fixyourownprinter.com/posts/29591 voltage power supplyand i still get the 922 errorI have http://www.dell.com/support/article/us/en/04/SLN162455 no idea what i should be checking nextam at a standstillTIA Respond to this 0 please try the cable who goes in the power supply// fuser, chech the pins and make sure good contact. sometimes i had this problem fuser error before. sorry for my writing. by pedrohuerta on Jun 2, 2005 at 3:59pm Add comment Please sign in to comment 0 received reply from lexmark" The “922 Fuser Error” is a cold fuser error. Since you have replaced the fuser twice, LVPS and the Engine board most likely to be service fuser error the issue with the DC auto connect which goes from the Fuser to the Engine board and the AC auto connect which goes from the Fuser to the LVPS which might be mal-functioning."am going to the office site to check thesewill post with results by Rubble on Jun 3, 2005 at 9:23am Add comment Please sign in to comment 0 Hi guys, I know it has been a while since the last post, but did you ever get a fix for that 922 error. I am having the same problem with a T622, Change Fuser, LVPS and Engine board. Any suggestion would be appreciated.Thanks by unknown on Nov 10, 2009 at 3:19pm Add comment Please sign in to comment Please sign in to comment Lexmark Optra T614 Buy discount ink Buy this printer More Lexmark questions © Copyright 2011-2016, FixYourOwnPrinter.com, Inc. Privacy Policy Terms of Use
5310n, printers Perform a power on reset of the printer. Turn the printer off. Disconnect the power and data cables from the printer. Wait at least five seconds. Reconnect the power and data cables of the printer. Turn the printer on. Ensure that the correct power requirements for laser printer are met. Always review the Owner's Manual of the Laser printer to determine the maximum wattage of the printer while printing. Always try to plug the laser printer directly to a wall outlet. Avoid plugging the laser printer into a power strip shared by other devices. Ensure that other outlets on the same circuit do not have “high power demand” devices in operation. Usually, one circuit breaker provides power to several outlets. NEVER plug a laser printer into an Uninterruptible Power Supply (UPS) system. The power demands of a laser printer are usually not compatible with the capabilities of small home and business UPS systems. Download and install updated firmware for Dell 5210n/5310n laser printer. Verify if the paper size and type settings in the operator panel matches the print media size and type being used on the printer. Press the Menu button. Press the Select button to select Paper Menu. Press the down arrow until Paper Size/Type appears and press Select. Press the down arrow until the specified tray appears. Then press the Select button. Open the paper tray. Verify the paper stop slider is set to the same paper size as the operator panel. Press the Select button. Verify the paper type in the tray is the same as the paper type in the operator panel. Determine if the fuser has been replaced for this issue. The fuser has not been replaced: Replace the Please contact Dell Technical Support for further advice. The fuser has been replaced: Please contact Dell Technical Support for further advice. Quick Tips content is self-published by the Dell Support Professionals who resolve issues daily. In order to achieve a speedy publication, Quick Tips may represent only partial solutions or work-arounds that are still in