925 Service Fuser Error
Contents |
brands HP Models Lexmark Models Xerox Models Model : Choose a brand Type : Choose a model My Account I Require An lexmark t630 922 service fuser error Access Code Technical Resources Maintenance Kits Fusers Toner Rollers & Pads Printers Search
920 Service Fuser Error
All Maintenance Kits Fusers Toner Rollers & Pads Printers Search All 920, 921, 922, 923, 924, 925 Service Fuser lexmark fuser error Errors A 920 FuserError message indicates that thefuser unit in the printer is below the proper temperature forprinting. 921 FuserError and 922 Fuser Error messages indicate that thefuser unit failed to http://support.lexmark.com/index?page=content&segment=SUPPORT&locale=en&userlocale=EN&id=SO5058&productCode=LEXMARK_T656 reach the standby temperature. If this isthe first time you have seen the error, turn the printer off. Leave the printer off for at least 10 seconds before turning it back on. This gives the printer's engine board a chance to reset. If this is an intermittent error, you may want to check how the printer is plugged in, even ifit has https://www.marketpoint.com/lexmark-error-code-92x-service-fuser-error.aspx worked on this surge device for months. Make sure the printer is plugged straight to the wall and not through a surge device or power strip. Power strips and uninterrupted power supplies can cause a low amperage problem in your printer whichcan trigger a false fuser error. If this does not help or if thiserror appears every time the printer is powered on, you will probably need service on the machine. A 923 FuserError indicates that the fuser unitis getting too hot while printing or when the printer is idle. Make sure that nothing is stuck inside the fuser unit that cancause the fuser unit to overheat. To check for any stuck sheets of paper in the fuser unit: Locate the rear door and open it. The rear door opens and dropsdown towards you. Look into the back of the printer. See if there is any paper or any other item stuck there that could be causing the fuser unit to overheat. If you cannot find anything jammed up or broken in the back of the printer,open the upper front cover of the printer and rem
manual to your list of manuals Page 86 highlights4060-xxx Fuser service checks Cold fuser service check Error codes 920, 921, and 922 may https://www.manualowl.com/m/Lexmark/T632/Manual/272846?page=86 display for a cold fuser failure. A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. A 925 service error indicates the wrong fuser lamp is installed. Be sure the correct type of fuser lamp is installed. CAUTION: There is a danger from hazardous voltage in the area of the printer where you fuser error are working. Unplug the printer before you begin, or use caution if the printer must receive power in order to perform the task. If the correct lamp is installed and a 925 error remains, the problem may be due to the following: • The fuser may have reached standby temperature too quickly. • The line voltage may be above the maximum rating for the printer. service fuser error Note: A 920, 921 or 922 fuser error may be caused by an incorrectly mounted thermistor. Service tip: Set the Fuser Temperature to NORMAL before starting this service check. FRU 1 Fuser lamp (incorrect lamp/ 925 Service Error) Action Install the correct voltage and wattage lamp or fuser assembly. See "Fuser assembly removal" on page 4-23. If the correct fuser lamp is installed and the 925 error remains, the fuser may have reached standby temperature too quickly. Check that the line voltage is not exceeding the maximum rating for the printer. Observe the lamp through the left side frame. If the lamp does not come on, do the following: • Remove the redrive assembly. • Remove the fuser assembly, disconnect the LVPS to fuser AC cable from the fuser assembly, and remove the fuser. See "Fuser assembly removal" on page 4-23. • Verify that the lamp is installed correctly. If correct, check the continuity of the fuser top cover assembly by verifying the lamp contacts on the right contact assembly. If incorrect, check continuity of the fuser lamp. If incorrect, replace the lamp. If correct, replace the fuser top cover assembly.