Fuser Error On Brother Printer
Contents |
Copier and Fax Repair 260-417-4807 Brother Tech ArticlesCanon Tech ArticlesCopyStar Tech ArticlesDell Tech ArticlesHP Tech ArticlesKyocera Tech ArticlesLexmark Tech ArticlesOkidata Tech ArticlesSamsung Tech ArticlesXerox Phaser Tech Articles Repair Tips for the Fuser Error On
Brother Hl-2270dw Manual
Brother MFC 8460, 8860, 8870, DCP 8060 Brother Tech Articles, DCP - 8060, DCP brother printers - 8065, MFC - 8460, MFC - 8860, MFC - 8870 Add commentsAug 252013 Troubleshooting the Fuser Error on the staples Brother MFC 8460, 8860, 8870, DCP 8060I have only seen this particular Fuser Error on a few machines. This error is typically more serious than other fuser related messages. Most times this problem will actually http://support.brother.com/g/b/faqend.aspx?c=us&lang=en&prod=hl2270dw_all&faqid=faq00002674_000 result in replacement of the fusing assembly. The actual error is related to a fuser too hot message. The service manual advices to check the environment and make sure it is not too hot. I also would check what you are printing. Printing on specialty paper can cause the fusing assembly to overheat if done in high volumes. Plus I would recommend checking the cooling vents and space around the machine. http://www.fortwayneprinterrepair.com/wordpress/2013/08/25/fuser-error-brother-8460-8860-8870/ Make sure the vents aren't blocked and the machine has 4 to 6 inch clearance on all sides. Turn the machine off, let it sit 15 to 20 minutes then try again. If it continues to show this fuser error follow the instructions below for the manual reset procedure and replacement instructions.Maintenance Mode Entry : DCP = Press Menu, Start, UP arrow 4 times, MFC Press Menu, *, 2, 8, 6, 4These button sequences have to be done in a certain amount of time. I typically tell customers to get a beat in their head and press the sequence to the beat and do not try to read what the control panel says as you press the buttons. If done correctly the machine will beep, the lights will blink, and the Display will read Maintenance. When the machine reads maintenance press the 9 button twice ( 9,9 ). Pressing 9 twice will take you out of maintenance mode and start the normal warm-up procedure. ---If fuser replacement is needed then you will want to reset the Maintenance Counter for the Fuser Maintenance Mode: Press buttons ( Menu,*,2,8,6,4 ) This might take a time or two so be patient. When done correctly the lights on the control panel lights w
Codes If you Brother laser printer, fax machine or all-in-one printer has stopped working then it will probably be displaying an http://www.brotherprinterrepairs.co.uk/common-errors/ error message. These error messages are there to help you troubleshoot your Brother machines fault and can help us assist you in resolving the problem. All Brother printers, fax machines and all-in-ones’ error messages are shown on their LCD display and show the word ‘error’, ‘error code’ or ‘machine error’ followed by an action (for example ‘Replace fuser error Laser Unit’) or an alphanumeric code. The alphanumeric code is used by looking up the relevant description in the user manual. We’ve put together what we think are the most common Brother error codes with an explanation of what they mean and what to do. We hope that you find it helpful, but if you’re still stuck fuser error on then use our price finder to discover the cost to repair your machine. Just Printers Multi-Functional Printers Fax Machines Error: E50 Error Code: Malfunction of fuser unit: The fuser unit is the part in the machine that gets hot to bond the print onto the paper. The printer has detected that there is a problem with the temperature, too hot or not heating up enough. Explanation: Switch the machine off for 5 minutes and then back on again. Leave the machine for 10 minutes and it may recover. If fault persists, the fuser unit will need replacing. What to do: Error: E51 Error Code: Malfunction of laser unit: The laser unit is the part of the printer that writes the information on the drum surface. The error code means that the laser beam is not being detected. Explanation: Switch the printer off and back on again. If error persists then the laser safety flap may be defective or the laser unit may need replacing. What to do: Error: E52 E