Dameware System Error 10061
Contents |
cookies • All times are UTC - 6 hours [ DST ] Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
General Network Configuration & Implementation Issues The information in this article dameware system error 53 applies to: DameWare Remote Support DameWare Mini Remote Control System errors dameware system error 2 are Microsoft Operating System errors, not DameWare System errors. Likewise, Winsock errors are Microsoft Windows Sockets dameware system error 1219 (TCP) errors. The vast majority of all Operating System errors encountered while using the DameWare NT Utilities or DameWare Mini Remote Control programs (i.e. System Errors, http://forums.dameware.com/viewtopic.php?f=9&t=193 Winsock Errors, etc.) are not directly related to DameWare software. Most often, these issues are directly related to some type of system or network configuration issue within a network environment and can usually be duplicated outside of DameWare software. The following are some examples of network configuration & implementation issues, along with some http://support.dameware.com/kb/article.aspx?ID=300005 additional links that may help troubleshoot these specific issues in the environment: System Error:31 The graphic device driver supports more than one (1) planes. http://www.dameware.com/kb/article.aspx?ID=400227 System Error: 51 ERROR_REM_NOT_LIST Windows cannot find the network path. Verify that the network path is correct and the destination computer is not busy or turned off. If Windows still cannot find the network path, contact your network administrator. http://www.dameware.com/kb/article.aspx?ID=300061 System Error: 53 ERROR_BAD_NETPATH The network path was not found. http://www.dameware.com/kb/article.aspx?ID=300059 System Error: 1300 ERROR_NOT_ALL_ASSIGNED Not all privileges or groups referenced are assigned to the caller. http://www.dameware.com/kb/article.aspx?ID=300085 System Error: 1707 RPC_S_INVALID_NET_ADDR The network address is invalid. http://www.dameware.com/kb/article.aspx?ID=300024 System Error: 1814 ERROR_RESOURCE_NAME_NOT_FOUND The specified resource name cannot be found in the image file. http://www.dameware.com/kb/article.aspx?ID=300092 Winsock Connect Error: System Error: 10050 Network is down. This error may be reported at any time if the Windows Sockets implementation detects an underlying failure. This could indicate a serious failure of the network system (that is, the proto
it. Unfortunately, the Winsock 10061 errors is not directly related to the DameWare Mini Remote Control program. Please make sure NetBios is enabled (i.e. NetBios over IP (NetBT/WINS), NetBios over IPX, etc...). You http://doc.helplib.com/help/4593b6f4520388ef59319b273ab7d26f should easily be able to duplicate this issue outside of our software by http://forum.oszone.net/thread-45592-3.html attempting to map a drive to a shared resource on the remote machine (i.e. Net use X: \MachineNameAdmin$). Please also verify that File & Printer Sharing is installed on the remote machine. Also, if the remote machine is on a different subnet, please also keep in mind that all the system error necessary "File & Printer Sharing" ports must also be open on the routers/firewalls between the machines for the Mini Remote Control program to remotely install, start, stop, or remove the DMRC Client Agent Service. Here is some additional information about the 10061 error that may help out: Although the Mini Remote Control (DMRC) program uses a single TCP port (default is TCP 6129 however dameware system error any valid TCP port can be used) to establish a remote connect session, other ports are required to be open to remotely install, start, stop, & remove the DMRC Client Agent Service, basically "File & Printer Sharing". The Mini Remote Control program will first attempt a TCP connection to the remote machine. If nothing is listening on the specified port (i.e. DMRC Client Agent Service not installed or a mismatch in TCP port usage), the DMRC program will drop out of it's TCP mode and use the installed protocols to attempt to interrogate the remote machine. If the DMRC program cannot find the remote machine via the installed protocols (i.e. configuration issue or ports blocked), you will receive the Winsock 10061 error. Please also keep in mind that if local & remote machines were on different subnets, the necessary ports must also be open on the routers between the subnets for the DMRC program to remotely install, start, stop, & remove the DMRC Client Agent Service. However, if the DMRC Client Agent Service were already installed on a remote machine, then only a single TCP port is
Microsoft » Программное обеспечение Windows » Система - DameWare Remote Support (DameWare NT Utilities) < Предыдущая 1 2 3 4 5 Следующая > Последняя » Настройки темы Система - DameWare Remote Support (DameWare NT Utilities) Queen Black ФерзЪ Сообщения: 769 Благодарности: 11 Профиль | Сайт | Отправить PM | Цитировать Изменения Автор: xoxmodav Дата: 01-11-2012 Описание: Шапка темы DameWare Remote Support (ранее называлась DameWare NT Utilities) Цитата Один из русскоязычных download-сайтов: DameWare NT Utilities - сборник утилит, предназначенных для удаленного администрирования операционных систем Windows NT/2000/XP. Это приложение включает в себя набор административных средств Microsoft Windows NT и централизованный интерфейс для удаленного управления серверами и рабочими станциями Windows NT/2000/XP. В состав DameWare NT Utilities входят все стандартные утилиты для серверов Windows NT/2000 и рабочих станций Windows NT/2000/XP, а также большое количество утилит DameWare NT, в том числе облегченный модуль дистанционного управления. Программа, предназначенная для управления корпоративными системами на платформе Windows NT/2000/XP/2003/Vista, позволяющая администраторам обойти ограничения Microsoft Management Console (MMC). DameWare NT Utilities (DNTU) включает большое количество средств администрирования Microsoft Windows, объединенных под одним общим централизованным интерфейсом, и позволяет удаленно управлять серверами и рабочими станциями Windows. Практически все стандартные утилиты, входящие в состав DNTU, доступны через интерфейс в стиле Проводника, большинство из них было улучшено для обеспечения высочайшей производительности, дополнительной функциональности и легкости в использовании. DNTU также включает специализированные средства, такие, как: DameWare Mini Remote Control и Exporter, а также поддерживает станд